HURST Mastershift 3-Speed Installation Kit Manuel utilisateur
WORK SAFELY: Perform this on a good clean level surface for maximum safety and with the engine
turned “off”. Apply parking brake and place blocks or wedges in front of and behind both rear wheels
to prevent movement in either direction.
CAUTION: To avoid any possibility of bodily injury or damage to vehicle, do not attempt disconnect or
installation until you are confident that the vehicle is safely secured and will not move.
ATTENTION: Due to variations in the auto manufacturing tolerances, the transmission rods supplied
with this kit may require slight bending to clear any obstructions, etc. Protect the threads while
bending. BEND RODS COLD! – DO NOT APPLY HEAT!
Disconnect the 1st-Reverse rod at the transmission control arm only. The stock 1st-Reverse rod is to
remain connected to the steering column lever. Remove 2nd-3rd stock linkage completely at both
ends.
1. Assemble the bracket and brace bolt, split-lockwasher and hex-nut as shown in exploded assembly
drawing.
2. Disconnect the speedometer cable coupling from the transmission and pass it through the hole in
the shifter mounting bracket. Re-connect the cable coupling to the transmission. Attach the bracket
and the stiffener brace assembly to the transmission as shown in assembly view, use the stock
transmission bolts. Tighten all bolts after all have been started.
3. Pierce a small hole through the floor directly in line with the top shifter mounting hole in the bracket,
about one inch away from the surface of the bracket. Use this pierced hole as a center to cut a hole
large enough to clear the shifter. The hole should have ¼” clearance around shifter
4. Install the shifter on the bracket and brace assembly (enlarge the opening in the floor tunnel, if
necessary). Tighten all the mounting hardware.
5. Assemble the arms with the respective rods using the bushings and spring clips. Refer to the
exploded assembly drawing and select the correct rods from the parts list according to the vehicle
(late or early). Thread rod adjusting buttons onto rods. Refer to the separate shifter alignment
instruction sheet for further directions to align and assemble linkage.
After the linkage has been connected and the shifter is operating properly, connect the backdrive
linkage to the 1-R arm. Refer to the instructions on page 2 for proper connection.
TechnicalSupport(707)544‐4761 1 www.HURST‐SHIFTERS.com
Installation Instructions
Mastershift 3-Speed Installation Kit
Fits: 1965-1973 Mustang V6 & V8 w/console and V6 w/out console
1967-1969 Mercury Cougar V8 / 1963 Mercury Meteor V8
Catalog# 3677640
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Technical Service
A highly trained technical service department is maintained by Hurst Performance to answer your
technical questions, provide additional product information and offer various recommendations.
Hurst offers a wide variety of custom T-Handles and knobs that can be sued with this shifter to allow
the driver to tailor the vehicle to his/hers personal liking. See your local retailer of Hurst products for
specific prices.
Technical service calls, correspondence, and warranty questions should be directed to:
Hurst Performance Products
(707) 544-4761
www.Hurst-Shifters.com
TechnicalSupport(707)544‐4761 2 www.HURST‐SHIFTERS.com
SPEEDOMETER
COUPLING CLAMP
AND HARDWARE
SPEEDOMETER
COUPLING
STOCK BACK-
DRIVE ROD &
LOCKNUT
CONTENTS OF KIT
1. MOUNTING PLATE
2. 5/16-18x1 FLAT HEAD SOCKET
SCREW
3. 5/16-18x1 HEX HEAD CAP SCREW
4. 5/16” SPLIT LOCKWASHER
5. 7/16-14x2 3/4 HEX HEAD CAP SCREW
6. 7/16” SPLIT LOCKWASHER
7. 7/16” FLATWASHER
8. 3/8-16x2 3/4 HEX HEAD CAP SCREW
9. 3/8” INTERNAL/EXTERNAL TOOTH
LOCKWASHER
10. BACK-UP LIGHT SWITCH BRACKET
11. ROD ADJUSTING BUTTOON
12. NYLON BUSHING
13. SPRING CLIP
14. ARM 1ST/REV.
15. ROD 1ST/REV.
16. ARM 2ND/3RD
17. ROD 2ND/3RD
STOCK NUT
STOCK
BACK‐DRIVE
ROD
BACK-UP LIGHT SWITCH BRACKET IS
INSTALLED UNDER JAM NUT ON 2ND
GEAR STOP BOLT.
SWITCH IS NOT INCLUDED
Autres manuels HURST Autre
