Hunter 146-59-1 Manuel
Setup Instructions for Remote Control
(146-59-1, 146-65-1, 146-78-1)
6754-T, 08-22, Supersedes, 6754-T, 02-16
This procedure should be performed only by an authorized factory representative.
This document provides information for installation and setup of the XF remote controller. Second genera-
tion remotes require a different procedure to set the wireless channel.
Setup for Remote Control
Console Channel Selection
NOTICE
In most cases, the wireless channel should be correctly set from the factory. Use this
procedure if there is a wireless channel conflict.
1. From the setup menu, under “Sensors”, select “Cordless Channel Selection”.
2. The console channel setting is displayed in the upper left corner. Highlight the desired channel from the
list below it then select “Set Channel”.
NOTICE
Channels on other devices such as conventional sensors, CodeLink®, remote indicator,
etc must also be changed at this time.
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 2 of 7
Second Design (146-59-1, 146-78-1, 146-65-1)
SETTING UP THE REMOTE CHANNEL
The wireless channel is selected using a set of dip switches on the main board. To set the wireless
channel,remove the four screws securing the back cover of the device, then remove the back cover.
NOTICE
Be careful not to lose the black rubber plug over the data port.
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 3 of 7
Remove the batteries from the device, then remove the three screws securing the main board.Gently turn
the board over to access the dip switches on the opposite side.
NOTICE
You can leave the ribbon cable and power wires connected, the dip switches can be
accessed without disconnecting them.
Set the dip switches in sequence for the desired channel using the table below.
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 4 of 7
Re-install the board, install the batteries, then in-
stall the back cover. Make sure the data port plug
is in place while assembling the case halves.
Check the remote for proper operation.
Battery Replacement
WARNING
The port on the bottom is not a charging port, it is a data connection for future devices. Do
not connect any charging adaptors to this port.
To replace the batteries, remove the two screws securing the battery cover then gently pry off the cover.
Replace the batteries with two new “AA” size batteries, making sure to observe the correct polarity.
Replace the the battery cover and reinstall the two cover screws.
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 5 of 7
Troubleshooting
If the remote is still not connecting to the WinAlign console after several retries, refer to the steps below to
possibly identify a problem.
1. Verify XF pod or receiver board is connected to the PC. There should be a indicator light on the pod
showing that they are receiving power from the console.
2. Check to make sure that the remote control channel setting is set to “A,0” in “Remote Control Channel
Identification” under the “Aligner Equipment” heading in setup.
3. If the remote is still not connecting, it may be necessary to power down and unplug nearby WinAlign
consoles to remove interfering channels.
4. The batteries on the remote indicator may be dead and need to be replaced.
Compliance Statement
FCC
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
ISED
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two condi-
tions:
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 6 of 7
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes aux RSS ex-
emptes de licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement est
soumis aux deux conditions suivantes:
1. Cet appareil ne doit pas provoquer d'interférences.
2. Cet appareil doit accepter toutes les interférences, y compris les interférences susceptibles d'entraîner
un fonctionnement indésir-able de l'appareil.
ID (146-59-1)
FCC ID: LS3-146591
IC: 2938A-146591
Model: 146-59-1
Setup Instructions for Remote Control (146-59-1, 146-65-1, 146-78-1)
Page 7 of 7
ID (146-78-1)
FCC ID: LS3-146781
IC: 2938A-146781
Model: 146-78-1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Hunter Télécommande
Hunter
Hunter SimpleConnect 99107 Instructions de montage
Hunter
Hunter UNIVERSAL FAN AND LIGHT REMOTE CONTROL 27184 Manuel de service
Hunter
Hunter ICR Manuel de service
Hunter
Hunter 99771 Manuel utilisateur
Hunter
Hunter SRR Mode d'emploi
Hunter
Hunter 99123 Manuel utilisateur
Hunter
Hunter 99772 Manuel utilisateur
Hunter
Hunter 99116 Manuel utilisateur
Hunter
Hunter 99119 Manuel utilisateur
Hunter
Hunter ROAM XL Mode d'emploi
Hunter
Hunter 27157 Manuel utilisateur
Hunter
Hunter 99123 Manuel utilisateur
Hunter
Hunter 84592 Manuel utilisateur
Hunter
Hunter 99112 Manuel utilisateur
Hunter
Hunter Universal Fan and Light Remote Control Manuel d'instructions
Hunter
Hunter 99123 Manuel utilisateur
Hunter
Hunter 99371 Manuel utilisateur
Hunter
Hunter 21117 Mode d’emploi
Hunter
Hunter Roam Mode d'emploi
Hunter
Hunter 99373 Manuel utilisateur
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
