Hunter Institutional I-40 Manuel utilisateur

Fig. 1 Fig. 2

Nozzle

Retainer/

Range

Adjustment

Screw

Arc Adjustment

Socket

Fig. 3

Lift Up

Socket

Indicates

VStat®

Self-

Adjusting

Stator

Recess

for Nozzle

ID Button

Specific

Model

36S

I40

I-40

ADS

Fig. 4

Water

flow

Arc Adjustment

Direction



All I-40/41 group adjustable heads are preset to

approximately 180°. Sprinklers may be adjusted

with water on or off. It is recommended that

initial adjustment be made before installation.

1. Using the palm of your hand, rotate the

nozzle turret counterclockwise to left stop to

complete any interrupted rotation cycle.

(Fig. 1).

2. Rotate the nozzle turret clockwise to right

stop. This is the xed side of the arc. The

nozzle turret must be held in this position for

all arc adjustments.



1. Insert the key end of the Hunter wrench into

the adjustment socket (Figs. 2 & 3).

2. While holding the nozzle turret at the right

stop, turn the wrench clockwise. Each 360°

turn of the wrench increases the arc 45°.

3. Adjust to any arc between 40° and 360°.

4. Wrench will stop turning, or there will be a

ratcheting noise, when the maximum arc

(360°) is reached.



1. Insert the key end of the Hunter wrench into

the adjustment socket (Figs. 2 & 3).

2. While holding the nozzle turret at the right

stop, turn the wrench counterclockwise.

Each 360° turn of the wrench decreases

the arc 45°.

3. Adjust to any arc between 40° and 360°.

4. Wrench will stop turning, or there will be a

ratcheting noise, when the minimum arc

(40°) is reached.



Insert the hex end of the Hunter wrench into the

nozzle-retainer/range-adjustment screw (Figs. 2

& 3). Turn the screw clockwise into the stream

of water to decrease the radius, or counter-

clockwise to increase the radius.



Where excessively wet or dry areas are a

problem, the precipitation rate may be adjusted.

Simply replace the existing nozzle with a larger

one to increase, or a smaller one to decrease

the rate of precipitation.



1. Insert the key end of the Hunter wrench

into the lifting socket of a pop-up sprinkler.

Pull the riser up to gain access to the

nozzle socket.

2. Using the Hunter wrench, loosen the nozzle-

retainer/range-adjustment screw. If a nozzle

is already installed in the sprinkler, it may

now be removed by briey turning on

the water.

3. Discard nozzle if removed with pliers.

Slip the desired nozzle into the nozzle

socket. Note that the socket is angled up

25° (see Fig. 4). Tighten the nozzle-retainer/

range-adjustment screw.

 

Gear-Driven Sprinklers

1940 Diamond Street • San Marcos, California 92078 P/N 700144 LIT-144 11/06

www.HunterIndustries.com

Each nozzle can be identified by

the number of raised ridges on the

inside surface of the nozzle.

Example: 2 ridges = # 42 nozzle

I-40/41 = 3 minutes (approx.)

I-42/43 = 1 minute (approx.)

Each nozzle can be identified by

the number of raised ridges on the

inside surface of the nozzle.

Example: 2 ridges = # 42 nozzle

I-40/41 = 3 minutes (approx.)

I-42/43 = 1 minute (approx.)

I-40 Nozzle Performance Data

Pressure Radius Flow Precip in/hr

Nozzle PSI ft. GPM

45'

46'

7.0

8.0

8.5

0.67

0.73

0.77

0.84

0.89

50'

51'

52'

53'

10.2

11.1

12.1

13.0

0.79

0.82

0.86

0.89

0.91

0.95

0.99

1.03

51'

53'

55'

56'

11.0

12.3

13.1

13.9

0.81

0.84

0.83

0.85

0.94

0.97

0.96

0.99

56'

57'

59'

61'

13.5

15.1

16.1

17.5

0.83

0.89

0.91

0.96

1.03

1.05

63'

65'

66'

67'

20.0

21.8

23.4

24.9

0.97

0.99

1.03

1.07

1.12

1.15

1.19

1.23

66'

68'

69'

70'

22.7

24.7

26.4

28.2

1.00

1.03

1.07

1.11

1.16

1.19

1.23

1.28

Note: All precipitation rates are calculated for 180 degree operation.

For the precipitation rate for a 360 degree sprinkler, divide by 2.

I-42 Nozzle Performance Data

Pressure Radius Flow Precip in/hr

Nozzle PSI ft. GPM

41'

42'

7.0

8.0

8.5

0.80

0.87

0.93

1.01

1.07

44'

45'

46'

10.2

11.1

12.1

13.0

1.01

1.10

1.15

1.18

1.17

1.27

1.33

1.37

46'

47'

49'

50'

11.0

12.3

13.1

13.9

1.00

1.07

1.05

1.07

1.16

1.24

1.21

1.24

51'

52'

53'

13.5

15.1

16.1

17.5

1.00

1.07

1.15

1.20

1.15

1.24

1.32

1.38

58'

60'

20.0

21.8

23.4

24.9

1.14

1.25

1.33

1.32

1.44

1.54

60'

62'

64'

65'

22.7

24.7

26.4

28.2

1.21

1.24

1.28

1.40

1.43

1.48

Note: All precipitation rates are calculated for 180 degree operation.

For the precipitation rate for a 360 degree sprinkler, divide by 2.

Each nozzle can be identified by

the number of raised ridges on the

inside surface of the nozzle.

Example: 2 ridges = # 42 nozzle

I-40/41 = 3 minutes (approx.)

I-42/43 = 1 minute (approx.)

I-41 Nozzle Performance Data – Metric

Nozzle

Pressure

Bars kPa

Radius

Flow

m3/hr l/min

Precip mm/hr

2.5

3.0

3.5

4.0

4.5

5.0

248

303

352

400

448

496

13.4

13.7

14.0

14.3

1.52

1.68

1.80

1.92

2.03

2.13

25.4

28.0

30.0

32.0

33.8

35.5

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

14.9

15.2

15.5

15.8

16.2

2.16

2.33

2.49

2.64

2.79

2.95

36.0

38.9

41.5

44.1

46.5

49.1

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

15.2

15.5

16.2

16.5

16.8

17.1

2.37

2.54

2.71

2.87

3.01

3.17

39.4

42.4

45.2

47.8

50.2

52.9

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

16.8

17.1

17.4

17.7

18.0

18.6

2.87

3.11

3.33

3.55

3.75

3.97

47.9

51.8

55.6

59.1

62.4

66.1

4.0

4.5

5.0

5.5

6.0

6.5

400

448

496

552

600

648

19.2

19.5

19.8

20.1

20.4

4.47

4.75

5.02

5.31

5.56

5.80

74.4

79.1

83.6

88.5

92.6

96.6

4.0

4.5

5.0

5.5

6.0

6.5

400

448

496

552

600

648

20.1

20.4

20.7

21.0

21.3

21.6

5.07

5.38

5.68

6.01

6.28

6.55

84.4

89.7

94.7

100.2

104.7

109.1

Note: All precipitation rates are calculated for 180 degree operation.

For the precipitation rate for a 360 degree sprinkler, divide by 2.

I-43 Nozzle Performance Data – Metric

Nozzle

Pressure

Bars kPa

Radius

Flow

m3/hr l/min

Precip mm/hr

2.5

3.0

3.5

4.0

4.5

248

303

352

400

448

12.2

12.5

12.8

13.1

1.52

1.68

1.80

1.92

2.03

25.4

28.0

30.0

32.0

33.8

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

13.1

13.4

13.7

14.0

2.16

2.33

2.49

2.64

2.79

2.95

36.0

38.9

41.5

44.1

46.5

49.1

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

13.7

14.0

14.3

14.6

14.9

15.2

2.37

2.54

2.71

2.87

3.01

3.17

39.4

42.4

45.2

47.8

50.2

52.9

3.0

3.5

4.0

4.5

5.0

5.5

303

352

400

448

496

552

14.9

15.5

15.8

16.2

2.87

3.11

3.33

3.55

3.75

3.97

47.9

51.8

55.6

59.1

62.4

66.1

4.0

4.5

5.0

5.5

6.0

6.5

400

448

496

552

600

648

17.7

18.3

4.47

4.75

5.02

5.31

5.56

5.80

74.4

79.1

83.6

88.5

92.6

96.6

4.0

4.5

5.0

5.5

6.0

6.5

400

448

496

552

600

648

18.3

18.6

18.9

19.5

19.8

5.07

5.38

5.68

6.01

6.28

6.55

84.4

89.7

94.7

100.2

104.7

109.1

Note: All precipitation rates are calculated for 180 degree operation.

For the precipitation rate for a 360 degree sprinkler, divide by 2.











Data represent test results in zero

wind. Adjust for local conditions.

Radius may be reduced up to 25%

with adjustment screw (this may alter

the uniformity of the spray pattern).

Ce manuel convient aux modèles suivants

Autres manuels Hunter Système d'irrigation

Hunter

Hunter Institutional Series Manuel utilisateur

Hunter

Hunter Institutional Series I-90 Manuel utilisateur

Hunter

Hunter Institutional Series I-25 Plus Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter Hydrawise Ready Manuel utilisateur

Hunter

Hunter Institutional Series I-35 Manuel utilisateur

Hunter

Hunter X-CORE Mode d'emploi

Hunter

Hunter ST Series Manuel utilisateur

Hunter

Hunter Institutional I-40 Series Manuel utilisateur

Hunter

Hunter ST Series Manuel utilisateur

Hunter

Hunter G800 Series Manuel utilisateur

Hunter

Hunter Professional Series PGP Manuel utilisateur

Hunter

Hunter I-80 Manuel utilisateur

Hunter

Hunter I-25 Ultra Manuel utilisateur

Hunter

Hunter Professional PGP Manuel utilisateur

Hunter

Hunter I-31 Plus Manuel utilisateur

Hunter

Hunter EC-401-A Mode d'emploi

Hunter

Hunter PGJ Manuel utilisateur

Hunter

Hunter Professional Series Manuel utilisateur

Hunter

Hunter ST Series Manuel utilisateur

Hunter

Hunter Professional PGP Ultra Series Manuel utilisateur

Hunter

Hunter I-60 Series Manuel utilisateur

Hunter

Hunter Institutional Series Manuel utilisateur

Hunter

Hunter SRC Plus 600i Manuel utilisateur

Manuels Système d'irrigation populaires d'autres marques

Cellfast

Cellfast 52-305 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuel utilisateur

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuel utilisateur

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuel utilisateur

Reliable

Reliable F1-300 Manuel utilisateur

Tyco Fire Product

Tyco Fire Product Gem F892 Manuel utilisateur

Netafim

Netafim NETBEAT Manuel utilisateur

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuel utilisateur

Tyco

Tyco CC3 Manuel utilisateur

Reliable

Reliable F4FR Manuel utilisateur

OpenSprinkler

OpenSprinkler OSPi Manuel utilisateur

EINHELL

EINHELL GE-WW 5537 E Manuel utilisateur

Valley

Valley Bender160 Manuel utilisateur

Reliable

Reliable F1FR42 Series Manuel utilisateur

Reliable

Reliable F1FR-300 Manuel utilisateur

Toro

Toro 730 Series Guide rapide

Eden

Eden 97063-EDAMZ Manuel utilisateur

Tyco

Tyco TY-L Series Manuel utilisateur