Hunter TRIBECA 28120 Manuel utilisateur
TribecaTM
Installation Instructions
41765-01 06/22/2005
CAUTIONS
• Read entire installation instructions carefully before beginning instal-
lation and save these instructions.
• To avoid possible risk of electrical shock and re, install this light x-
ture only on Hunter TribecaTM fans, models 28120, 28121 and 28122.
Note: To nd the fan model number, check the ceiling fan package or
on the nameplate label located on top of the motor housing of the
ceiling fan.
WARNINGS
• To avoid possible electrical shock, before installing light xtures dis-
connect power by turning o the circuit breakers both to the outlet
box and to its associated wall switch location. If you cannot lock the
circuit breakers in the o position, securely fasten a prominent warn-
ing device, such as a tag, to the service panel.
• Connect house wiring to the fan before attaching the light xture to
the fan.
• All wiring must be in accordance with national and local electrical
codes. If you are unfamiliar with wiring, you should use a qualied
electrician. Professional installation is recommended.
• To reduce the risk of re or personal injury, allow bulbs and surround-
ing surfaces to cool to room temperature before touching or remov-
ing them.
Troubleshooting
Light does not come on.
1. Push the light button on the remote transmitter. Verify remote operation.
Refer to fan manual for remote operation and troubleshooting.
2. Make sure bulbs are installed properly and lament is not blown.
3. Make sure breakers or fuses are on.
4. Verify that the light power lead is connected at the ceiling. Refer to your
ceiling fan manual for locating assembly and wiring.
Glass rattles.
1. Make sure the glass globe is secure.
For other problems or ques-
tions, contact the Hunter Fan
Company Technical Support
at
1-888-830-1326 or
http://www.hunterfan.com
is light xture is for use
only on Hunter TribecaTM
Ceiling Fans, models 28120,
28121, and 28122.
1. Disconnect power to the ceiling fan by turning o the circuit breakers both to the
outlet box and to its associated wall switch location.
2. Find the empty lower switch housing that came with your TribecaTM fan. If you are
not sure what this piece is, refer to your TribecaTM fan manual.
Note: If your TribecaTM fan is already installed, you will need to remove the fan
only switch housing before proceeding. Refer to your TribecaTM fan manual.
3. On the light kit housing, nd the three recessed trim bezel screws and remove
them. Remove the trim bezel. Do not discard these screws. You will reuse them.
Note: e illustrations in the manual assume you are installing the light kit with
the globe tter. If you want to use the light kit without the globe, remove the
three globe tter screws and the globe tter. Retain the globe tter and the screws
in case you want to use the globe tter in the future.
4. read the wires from the light kit through the hole in the center of the switch
housing. Attach the lamp holder assembly to the switch housing. Use 2 #6-32 x
5/8 inch screws. Align the holes and tighten the screws.
5. Connect the black wire in the light to the black wire with white stripe in the fan.
Connect the white wire in the light to the white wire in the fan. Secure both wire
connections with the ceramic wire nuts provided.
6. Attach switch housing to fan using three side screws provided with the fan.
Step 3
Globe Fitter Trim Bezel
Globe Fitter
Screw
Recessed Trim
Bezel Screw
Step 4
Switch
Housing
Steps 5–6
7. Use the three screws from step 3 to reattach the trim bezel to the lamp holder as-
sembly. Tighten the screws securely.
8. Install a 50-Watt, GU-10 based halogen lamp (included) into each of the three
lamp sockets. Be sure to insert the pins on each lamp into the receptacle in the
xture and twist the lamp clockwise to secure it. If you are not installing the globe,
your installation is complete and you can restore power to the ceiling fan. Other-
wise, proceed with step 9.
9. Raise the glass globe and align the indents in the glass globe with the tabs on the
tter. Twist the glass globe clockwise to secure it. e installation is complete and
you can restore power to the ceiling fan.
Step 7 Trim Bezel Step 8
Halogen Lamp
Step 9
Fitter
Tab
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
Printed in China & Taiwan
is Light Fixture weighs 2.75 lbs. © 2005 Hunter Fan Company
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Hunter Ventilateur
Hunter
Hunter Type 2 Series Manuel de service
Hunter
Hunter Hunter Ceiling fans Manuel utilisateur
Hunter
Hunter Type 5 Models Manuel d'instructions
Hunter
Hunter 2nd Century Original Manuel utilisateur
Hunter
Hunter 28671 Manuel
Hunter
Hunter MODEL TYPE 7 23347 Manuel de service
Hunter
Hunter Antero 52128 Manuel utilisateur
Hunter
Hunter Jetty Manuel utilisateur
Hunter
Hunter Type 2A Models Manuel d'instructions
Hunter
Hunter 7 Models Manuel utilisateur
Hunter
Hunter Builder Plus Manuel utilisateur
Hunter
Hunter 28487 Manuel
Hunter
Hunter 50326 Manuel utilisateur
Hunter
Hunter Type T series Manuel d'instructions
Hunter
Hunter 54151 Manuel utilisateur
Hunter
Hunter Allendale 53302 Manuel utilisateur
Hunter
Hunter 23949 Manuel de service
Hunter
Hunter 51264 Manuel utilisateur
Hunter
Hunter Hunter Ceiling Fan Manuel utilisateur
Hunter
Hunter Hunter Ceiling fans Manuel utilisateur
