Hunter Hydrawise HPC Manuel utilisateur

HPC - Using Hunter Remotes

The HPC face panel quickly and easily upgrades Pro-C® controllers (PC400 models

manufactured since March 2014) to next-generation smart controllers via the Hydrawise

platform. In addition, it lets contractors continue using their Roam and Roam XL remotes

for quick on-site management. HCC is also compatible with Hunter’s ROAM and ROAM XL

remotes, allowing for fast and reliable manual operation in the field from long-range

distances without the need for a smartphone. There is no need to remove the smart port

adapter from the controllers when doing a facepack upgrade.

Compatible models include all Hunter remotes: SRR, ICR, ROAM, and the ROAM-XL.

If the Smartport is not installed on the controller, see illustrations below for wiring

instructions.

Note: Any extension of the wiring on the SmartPort may result in an error message in

the controller display and possible malfunction of the remote unit due to radio interference.

In

some situations, lengthening of the harness may work fine, in others it may not work at all

(it is

site specific). In either case, extending the wiring harness should be done using shielded

cable to

minimize the possible effects of electrical noise. For easiest installation, order the Hunter

SmartPort shielded cable wiring harness. (P/N ROAM-SCWH) with a full 25' (7.6 meters)

of

shielded cable.

Wiring

1. Bottom 24 VAC terminal - Red wire

2. Second 24 VAC terminal - White wire

3. Remote terminal - Blue wire

Smart Port Wiring

Copyright 2020 Hunter Industries. All Rights Reserved. 1

Operation

The ROAM System will allow you to remotely turn on and off any station on your Hunter

controller with the press of a button. Once on, the station will run for the run time you have

designated in the remote. To remotely activate a station, follow the steps below:

1. Plug the receiver into a SmartPort® that is connected to a powered controller. The

receiver will beep 4 times followed by a 10-second pause and a single beep.

2. If your transmitter is not on (no display), wake it up by pressing and holding the MODE

button for 5 seconds. The Transmitter will display the active station.

3. Use the up and down buttons to display the station you would like to start.

4. Press the "Green Play Button" to start the station. The Transmitter will display the

Transmit icon . If you are near the receiver, you will hear it beep 2 times. This indicates

that the Receiver has received the command.

5. Press the "Red Stop Button" to turn off any station that is on. The display will show

the Transmit icon and receiver will beep again twice. The ROAM System is designed to

turn on

one station at a time (unless you activate a program). Therefore, turning a station on

while another station is operating will cause the operating station to turn off.

NOTE: The ROAM remote can activate any station on the controller whether the controller

dial is in the “SYSTEM OFF”, “RUN” or “RUN/BYPASS SENSOR” modes. If a sensor

device has been wired to the controller, the ROAM remote will NOT override the sensor for

Copyright 2020 Hunter Industries. All Rights Reserved. 2

manual operation. For more programming information, please see attached manuals for

both the ROAM and ROAM XL remotes.

Copyright 2020 Hunter Industries. All Rights Reserved. 3

Ce manuel convient aux modèles suivants

6

Table des matières

Autres manuels Hunter Contrôleurs

Hunter

Hunter SRC Plus Manuel utilisateur

Hunter

Hunter ICC2 Manuel utilisateur

Hunter

Hunter Pro-C Manuel utilisateur

Hunter

Hunter Hydrawise Pro-HC Guide de démarrage rapide

Hunter

Hunter Hydrawise Pro-HC Manuel utilisateur

Hunter

Hunter 600-Z Manuel utilisateur

Hunter

Hunter X-CORE Manuel utilisateur

Hunter

Hunter X-CORE XC-2 Manuel utilisateur

Hunter

Hunter 27206 Manuel utilisateur

Hunter

Hunter 99373 Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter Pro-C Mode d'emploi

Hunter

Hunter Pro-C Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter SRC Plus Manuel d'installation et d'exploitation

Hunter

Hunter VSX Manuel utilisateur

Hunter

Hunter Genesis Manuel utilisateur

Hunter

Hunter Hydrawise HC-1200M Manuel utilisateur

Hunter

Hunter XC HYBRID Series Mode d’emploi

Hunter

Hunter Pro-C Mode d'emploi

Hunter

Hunter XC Hybrid Mode d'emploi

Hunter

Hunter EC Manuel utilisateur

Hunter

Hunter WVC Mode d'emploi

Hunter

Hunter ICC-800PL Mode d'emploi

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur