Hunter Stoves Hawk Guide de l'utilisateur

Revision D 30/08/2012

HAWK

GAS STOVE

Installation and Servicing

Instructions

Please leave this instruction booklet with the user after the installation is

complete Leave the system ready for operation and instruct the user in the

correct use of the appliance and operation of its controls

Please refer to the appliance data plate for the specific model type

Contents

TECHNICAL DATA...........................................3

TOVE

IMENSIONS

................................................................................................ 3

INSTALLING THE APPLIANCE ....................4

INSTALLATION NOTES

....................................................................................... 4

LUE

RRANGEMENT

.............................................................................................. 6

DDITIONAL

ENTING

(GB

NLY

) ................................................................... 6

PENING THE

TOVE

OOR

....................................................................................

UPPLY

ONNECTIONS

.....................................................................................

ESTING

UPPLY

RESSURE

...................................................................................... 8

INSTALLATION OF THE FIRE-BED INTO

THE STOVE .......................................................8

FIRE-BED ARRANGEMENT ............................................................... 9

ITTING THE

ERAMIC

ATRIX

............................................................................... 9

Section A - Fitting the Loose Ceramic Coals

........................................................... 10

Section B - Fitting the Loose Ceramic Logs

............................................................ 12

ITTING THE

ANOPY

–

PTIONAL

) ...................................................................... 15

EST FOR

PILLAGE

............................................................................................... 16

PILLAGE

ONITORING

YSTEM

............................................................................ 16

SERVICING INSTRUCTIONS ....................... 1

SPARES

LIST ................................................................................................ 18

Please read these instructions carefully

It is important that your stove is correctly installed as Hunter

Stoves Limited cannot accept responsibility for any fault

arising through incorrect installation.

TECHNICAL DATA

NATURAL GAS

Nominal Gas Pressure

20mBar

Supply Gas Type/Category

G20/I

Jet Type/Size

82/260

Heat Input (Gross)

Full

Low

4. kW

3.5kW

Gas Flow Rate (m

/h)

Full

0.42 m

Class

Efficiency Class

Countries of Destination

GB & IE Only

Stove Dimensions

Diagram 1

INSTALLING THE APPLIANCE

Pre-installation notes

1 Check the stove data plate to establish the gas type required The data plate can

be found bolted to the inside of the door

Before installation check that the local distribution conditions, nature of the gas

and pressure, and adjustment of the application are compatible

2 This appliance is intended for use on a gas installation with a governed meter

3 A GAS SAFE REGISTERED INSTALLER or equally recognised competent

person must fit the appliance That person is legally responsible for the safe

installation of the appliance with due regard to all relevant local and national

building regulations

4 All outer surfaces of the stove excepting the gas control knob and valve cover

flap are defined as working surfaces

Installation site

5 Any installation area previously used for a solid fuel fire or stove would probably

be deemed suitable for the appliance

6 It should be noted that heat given off from this appliance might affect articles

placed close to it Curtains should not be positioned above the appliance or

within 300mm of the sides Caution should also be taken sighting the appliance

near to ‘embossed’ type wallpapers

7 The appliance must be sited on a non-combustible hearth of minimum 12mm

thickness

8 The hearth should be edged or raised to prevent combustible floor finishes

(e g Carpet) from being laid too close to the appliance

Clearances

9 For the relevant clearance distances for installing the appliance see diagram 2 on

page 5

IMPORTANT NOTE! Adequate clearance must be given between the

appliance and the walls so that a satisfactory spillage test can be performed

as detailed on page 16

MINIMUM CLEARANCE DISTANCES TO:

DIMENSION

DESCRIPTION

COMBUSTIBLE

MATERIAL

NON-COMBUSTIBLE

MATERIAL

Side of stove to wall 150mm 100mm

Top of stove to underside of

opening or shelf

250mm 200mm

Rear of stove to wall 150mm 100mm

Minimum distance for hearth

to extend in front of stove

50mm 50mm

Diagram 2

Clearance Distances for Diagram 2

Flue Arrangement

The GAS SAFE REGISTERED ENGINEER commissioned to install this

appliance is wholly responsible for deciding the suitability of any flue

arrangement to operate in conjunction with this gas appliance.

The chimney or flue system that is to be fitted to the Hawk gas stove must comply with

the current rules in force

(The Hawk gas stove is also suitable for other specific class 2 installation arrangements:

pre-cast flues, ridge-vent flues and pre-cast chimney block and with the relevant

adaption, the appliance will operate in a closure plate type system )

It is suggested to run flue pipe at least 615mm vertically from the unit before there are

any changes in direction of the flue system Wherever possible horizontal runs of the flue

system should be avoided

It is suggested that the flue has a minimum of 3 meters of vertical height Please note for

rear flue appliances it is recommended that the vertical flue run be established as soon as

is practical from the rear flue exit (Caution should be taken locating the exit of the flue

as explained in ‘The Building Regulations - Document J’ )

Before commencing any installation work the installing engineer must check that the flue

is free from all blockages, the chimney should be given a precautionary clean, and finally

the chimney should be smoke tested to ensure soundness Additionally any flue dampers

must be permanently fixed open or removed altogether

The flue collar and flue blanking plate should be fitted to the stove using the supplied

gaskets

Additional Air Venting (GB Only)

The supply gas heat input into the appliance is nominally less that 7kw, therefore under

the directives of the current gas safety and use regulations (1995) No additional air vents

are required in the room the appliance is situated

Opening the Stove Door

NOTE! This appliance must never be used with the door open or removed.

Before gaining access to the burner tray, first make sure that the stove is switched off and

is cold Now the cast iron door can be opened, this is secured in place by one fixing bolt

Firstly remove the door handle by turning anticlockwise

Keep turning until the handle is completely removed, as

shown in diagram 3

The door-fixing bolt can then be removed using a

13mm spanner as shown in diagram 4

Gas Supply Connections

The appliance is supplied with an 8mm Bundy pipe and an 8mm compression elbow to

allow easy connection to the mains gas supply This gas supply pipe should incorporate a

gas service isolation tap that is situated within 1 metre of the application

Diagram 5 shows the 8mm Bundy pipe

being fitted to the gas inlet on the valve

The compression joint is tightened with a

14mm open-ended spanner

Diagram 3

Diagram 4

Diagram 5

Testing Supply Pressure

ALWAYS CLOSE TEST POINTS AFTER USE!

The gas pressure at the appliance is measured with the

appliance running at full rate (For information on

how to achieve ‘full rate’ read ‘Lighting the main

burner’ in the ‘Operating the Appliance’ section of the

User Instructions)

The test point should be opened with flat bladed screwdriver and

is shown in diagram 6

Burner Gas Pressure should be:

Natural Gas@ 19mBars +/- 0.3mBar

INSTALLATION OF THE FIRE-BED INTO

THE STOVE

IMPORTANT NOTE!!

CERAMIC COALS AND LOGS GET VERY HOT! NEVER ATTEMPT TO

HANDLE HOT COALS OR LOGS WITH BARE HANDS AND NEVER PLACE

HOT COALS OR LOGS ON OR NEAR COMBUSTIBLE SURFACES

NO RESPONSIBILITY FOR ANY INJURY HOWEVER CAUSED WHILST

HANDLING HOT COALS, LOGS OR CERAMICS CAN BE ACCEPTED BY

HUNTER STOVES LTD

Test Point

Diagram 6

FIRE-BED ARRANGEMENT

ITTING THE

ERAMIC

ATRIX

Place the ceramic matrix onto the tray

top, making sure that the cut-outs in

both of the front bottom corners of the

ceramic line up with the corresponding

matrix positioning brackets on the tray

top This is shown in diagram 7

Pull the Ceramic matrix forward so that the

bracket fits into the hole, as described by

diagram 8 Looking from above the matrix,

make sure that the ceramic matrix does not

cover the holes in the tray top

The spacing with the bracket should central,

and even either side If you lift the matrix

slightly the channels underneath should line

up above the vertical slots in the burner

tray

This appliance can be fitted with either ‘coal effect’ or ‘log effect’ ceramics

If you are fitting ‘Coal Effect’ ceramics please follow the instructions set out in ‘Section

A – Fitting the Loose Ceramic Coals’ - Page 10

If you are fitting ‘Log Effect’ ceramics please skip ‘Section A’ and follow the instructions

set out in ‘Section B – Fitting the Loose Ceramic Logs’ - Page 12

Diagram

Matrix Positioning

Bracket

Cut-out in Ceramic

Diagram 8

Section A - Fitting the Loose Ceramic Coals

HOULD

AVE

5 x Small Ceramic Coals

4 x Medium Ceramic Coals

2 x Large Diamond Ceramic Coals

The first coals to be placed are the two ‘Diamond’

shaped coals These should be placed in diamond

shaped cut-outs as shown in diagram 9 Make sure

that the coals do not block the flame port holes in

the matrix

The next coals to be placed are four of the

medium coals In a similar fashion to the coals

already placed, these should be positioned around

the flame port holes in the matrix as shown in

diagram 10

Finally the five small coals are

located behind the existing row

of coals, this time to each side of

the rear holes in the matrix so

that they rest on the back of the

matrix As shown in diagram 11

The following page shows some larger pictures for clarity

Diagram 9

Diagram 10

Diagram 11

Autres manuels pour Hawk

Table des matières

Autres manuels Hunter Stoves Poêle

Hunter Stoves

Hunter Stoves HERALD 5 SLIMLINE CE VII Manuel utilisateur

Hunter Stoves

Hunter Stoves Double Hawk 4CE Manuel utilisateur

Hunter Stoves

Hunter Stoves Hawk Manuel utilisateur

Hunter Stoves

Hunter Stoves Herald 8 Double-Double CE Manuel utilisateur

Hunter Stoves

Hunter Stoves Telford Inset 20DB CVWSTI08DBFM Manuel utilisateur

Hunter Stoves

Hunter Stoves HS Gas SELENE 6 D Guide de l'utilisateur

Hunter Stoves

Hunter Stoves Double Herald 14 CE Manuel utilisateur

Hunter Stoves

Hunter Stoves Herald 5 Manuel utilisateur

Hunter Stoves

Hunter Stoves Herald 6 CE VII Guide de l'utilisateur

Hunter Stoves

Hunter Stoves Herald 80B CE V.II Manuel utilisateur

Hunter Stoves

Hunter Stoves HUNTER HAWK 4 MKII Manuel utilisateur

Hunter Stoves

Hunter Stoves HERALD 8 SLIMLINE CE vII Manuel utilisateur

Hunter Stoves

Hunter Stoves Inglenook Stove Manuel utilisateur

Hunter Stoves

Hunter Stoves Herald 6 CE VII Manuel utilisateur

Hunter Stoves

Hunter Stoves Telford Inset 5 MKII Manuel utilisateur

Hunter Stoves

Hunter Stoves Hawk Manuel utilisateur

Hunter Stoves

Hunter Stoves Hawk 3 MKI Manuel utilisateur

Hunter Stoves

Hunter Stoves Inglenook CEV. II Manuel utilisateur

Hunter Stoves

Hunter Stoves Double Hawk 4 CE Manuel utilisateur

Hunter Stoves

Hunter Stoves DI Lusso Eco R6 Cube Manuel utilisateur

Hunter Stoves

Hunter Stoves HERALD 8 SLIMLINE CE vII Manuel utilisateur

Hunter Stoves

Hunter Stoves herald 8 mk 2 Manuel utilisateur

Hunter Stoves

Hunter Stoves HERALD SERIES Manuel utilisateur

Hunter Stoves

Hunter Stoves Hawk Guide de l'utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur