Hugo 008 PRO Manuel utilisateur

ELECTRICAL KICK-BIKE

(KICK-BIKE WITH AUXILIARY ELECTRICAL MOTOR)

HUGO BIKE

TYPE 008 PRO

Congratulations on your purchase of the luxury electrical kick-bike HUGO Bike, which will grant you with an

extraordinary experience of riding it for miles comfortably and with smile on your face.

Please keep in mind that improper installation and handling of this electrical kick-bike could decrease its

performance and worsen your riding experience. Therefore before using this product please read this

operational manual thoroughly and follow every item in installation manual!

Thank you again for your purchase of our unique electrical kick-bike HUGO Bike!

TABLE OF CONTENTS

TABLE OF CONTENTS ......................................................................................................................................... 2

RIDING ON THE BUBLIC ROADS ......................................................................................................................... 3

SPECIFICATIONS................................................................................................................................................. 4

ELECTRICAL KICK-BIKE HUGO BIKE .................................................................................................................... 5

INSTALLATION MANUAL.................................................................................................................................... 6

FINAL INSPECTION............................................................................................................................................. 6

BATTERY INTALLATION AND DISMANTLING...................................................................................................... 8

BATTERY CHARGING ........................................................................................................................................ 10

BATTERY STORAGE .......................................................................................................................................... 11

ELECTRICAL KICK-BIKE RANGE ......................................................................................................................... 12

MAINTENANCE ................................................................................................................................................ 13

PROBLEMS AND THEIR SOLUTION................................................................................................................... 14

SAFETY WARNING............................................................................................................................................ 15

SAFETY NOTICE!!! ............................................................................................................................................ 16

WARRANTY ...................................................................................................................................................... 17

RIDING ON THE PUBLIC ROADS

If you are riding the electrical kick-bike on the public road, you are bound to observe all the rules of the road

that are valid in your country. The kick-bike is equipped for the road use in accordance with the law of Czech

Republic and the manufacturer bears no liability for any accident, damage or penalty caused by the use of

the electrical kick-bike in the way that is in conflict with the local legislation.

Please familiarize yourself thoroughly with the local legislation regarding this type of vehicle and follow it to

the letter.

It is recommended to use the safety helmet and high visibility vest while riding on the public road, along with

knee, elbow and spine protectors, reinforced gloves and shoes. Following these safety requirements will help

you to prevent serious injuries and damages. The rider is fully responsible for his safety!

In case that your kick-bike is not equipped with the front white light and rear red light, it is in accordance

with Czech road laws not suitable for the operation in decreased visibility.

Electrical kick-bike shall not be operated by the persons with lowered ability to keep balance, bad sight or

other medical or movement restriction.

Electrical kick-bike is in general a sport equipment and not a road vehicle.

SPECIFICATIONS

Max. Bearing capacity: 100 kg

Fork: spring fork

Front brakes: disk brake

Rear brakes: disk brake

Rims: aluminium (26“ front and 16“ rear)

Motor power: 1000 W

Battery: Li-ion 48V up to 20Ah

Charge time: 6-8 hours

Dimensions (l x w x h): 164 x 35 x 105 cm

Weight without batteries: 22 kg

Handle bars: wide

ELECTRICAL KICK-BIKE HUGO BIKE

PICTURE 1

PICTURE 2

Description of picture 1 and 2

1. Rear brake handle with disconnecting switch

2. Handle bars

3. Handle bar attachment piece

4. Front spring fork

5. Front wheel

6. Front wheel axis

7. Front brake callipers

8. Accelerator with battery indicator

9. Front brake handle with disconnecting switch

10. HUGO Bike frame

11. Battery, control unit and external electrical

installation

12. Standing plate

13. Rear wheel with electrical motor

14. Rear brake callipers

15. Turning rear wheel safeguard

16. Feed connector (picture 2)

INSTALLATION MANUAL

Please remove all packaging material and inspect the kick-bike if there was no damage during the transport.

When the kick-bike is delivered by delivery service or courier, it is usually divided into three parts:

-Handle bars

-Front wheel

-Rim with the rear wheel including other equipment

Necessary tools (not part of the delivery):

-Allen key 4, 5 & 6

-Nut key 15

Installation instructions:

1. Extract all parts from the transport package

2. Insert the handle bars into the handle bar hole

3. Use the allen key 5 or 6 (according to the handle bar type) to fasten the screw in the handle bar

holder.

4. Loosen the end nuts on the front wheel axis using the nut key 15 (if the fast attachment system is

used, fasten the handle and unscrew)

5. Attach the front wheel into the front fork (in accordance the direction shown on the tire if available)

and fasten the nuts (see item 3) so that there is no spontaneous loosening possible.

6. Attach the front wheel so that the disk fits into the brake callipers attached to the spring fork.

FINAL INSPECTION

After you have finalized the installation, conduct the final inspection and make sure that:

Each screw is properly tightened

Tires are pumped with the recommended value (shown on the tires)

Brakes are working properly

Inspect the proper operation of the brakes prior to every ride!

If the brakes are not used properly, you could lose control over your kick-bike. Braking your kick bike

requires a bit of practice to prevent you to put you or others into danger. Please go slow on your

first ride and brake gently to familiarize yourself with their operation. Front brake lever is located at

the left side of handle bars, the rear brake lever is on the right side.

If you have assembled and inspected the electrical kick-bike before the ride, turn on the power switch or key

by turning to “on” position. The battery indicator on the handle bars turns on and the electrical kick-bike is

prepared for the ride.

Notice: prior to every ride check the fastening of all screws, pressure in the tires

and brakes!

Notice: when you accelerate on full throttle from stopped position, you shall

expect that the motor power could imbalance you. To limit this risk we

recommend to use the accelerator after setting the kick-bike into motion by your

foot.

USING ALARM

Electrical kick-bike is equipped with the acoustic theft protection device, an alarm. The alarm is activated by

turning the start key to OFF position and pulling of the key out of the kick-bike. Alarm sound is activated at

the moment when the control unit notices that the rear wheel has turned. To disable the alarm, insert the

key and turn it to ON position.

The alarm is powered from the kick-bike battery and requires no maintenance. Alarm is not functional when

the battery is completely depleted.

BATTERY INTALLATION AND DISMANTLING

Picture 3

Picture 4

Dismantling

Turn the power off by turning of the key. Fasten the six screws on the edge of the standing plate (see picture

3). Remove the standing plate. Disconnect the connection cable from the battery (see picture 4) as well as

the charging connectors. Lift the battery straight up.

Installation

Proceed in reverse order. Please observe the correct polarity of the battery and charging connector!

Please make sure that the accumulator is fully charged prior to the first ride. Use only the charger that was

supplied with the electrical kick bike HUGO Bike. Using of different charger could damage or destroy the

battery or the kick-bike electronics, invalidating the warranty as well as creating the fire hazard. Make sure

that the charger uses the same voltage as in the country where you use the kick-bike.

BATTERY CHARGING

Battery supplied with the electrical kick-bike HUGO Bike will very slowly discharge when not in use. It is

therefore recommended to charge the battery frequently –at least always after you finish your ride and if

you are not using the kick bike every 14 days to full capacity.

Regardless to the battery state charge the battery after every ride! If you will take your charger with you,

you could re-charge during every stop, increasing the HUGO Bike range. Timely charging of your battery will

secure you with long lifespan, increased capacity and prevents damage.

Always have the power off during charging.

Battery charging:

1. Battery could be charged in electrical kick-bike or while removed from the frame, in which case you

have to use the reduction that is not part of the standard delivery. Charge the battery with the kick-

bike turned off.

2. Always connect the charger to the battery or kick-bike first and to the mains second.

3. Electrical connection shall meet the requirements on the charger.

4. When the charger is connected to the battery and mains, the red led indicator lights up, signaling the

start of the charging process. The charging will stop immediately when the battery is fully charged.

The charging is completed when the led indicator turns green.

5. Disconnect the charger from the mains first and from the battery second. Store the battery out of

the reach of children.

Maximal charging time is 5 –8 hours when the battery is fully depleted. The charger is supplied with the kick-

bike with the overcharge protection and will stop the charging process when the battery is fully charged.

Warranty conditions for the battery in relation with its capacity, charging cycles and age are listed at the end

of this document.

Notice: use only the charger supplier with the electrical kick-bike or charger

designated to the exact battery type used. Otherwise you could irreversibly

damage the battery or the charger.

Notice: Never charge the battery in wet environment. This could lead to

destruction of the charger as well as damage to the kick-bike control unit.

Table des matières

Autres manuels hugo Scooter

hugo

hugo Scooter Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur

hugo 008 PRO Manuel utilisateur

Manuels Scooter populaires d'autres marques