Hubbell RDS50Z Manuel utilisateur

Installation Instruction for new

construction of a Door Jamb Switch

Kit (RDS50Z) Normally Closed

Door open lights ON, Door closed

lights are OFF.

3A, 125 Vac. 4.6 Cu Inch.

NOTICE: For installation by a qualified electrician in accordance with national and local electrical codes and the

following instructions.

CAUTION: RISK OF ELECTRICAL SHOCK. Disconnect power before installing.

CAUTION: Make sure that you follow local Electrical rules and regulations. If unsure, consult a qualified electrician.

NOTE: Do not install on a Metal door frame

NOTE: Use Copper Conductors only.

1) Create suitable cable entry in Door Frame.

2) Make an opening in Door Jam to suit Junction Box. (See

Fig. 2 for dimensions of Box). Create recess for Box

Ears to ensure Switch Plate is flush to door jamb when

installed.

3) Remove a knock out in Junction Box to accommodate

cable entry.

4) Insert cable through knock out and secure to box with

approved connector (not provided).

5) Fasten box to door jamb with 4 wood screws

(provided).

6) Connect GREEN/ BARE (ground) wire to ground screw

in back of junction box, connect Line and Load wires to

switch pig tail wires following national and local

electrical codes Use Fig. 1 for guidance.

7) Adjust shaft to proper depth on switch plate using

locknuts (provided) at the back and front of the switch

assy’ for contact with round kicker plate .

8) Using 2 short screws (provided), fasten the switch

plate to the box.

9) With power ON, Open and close door to verify proper

operation of the switch and adjust switch depth

accordingly.

10) Once proper positioning is established, install the

round kicker plate on the door side to face the switch

button, by fastening with the wood screw (provided).

11) Installation is complete.

Fig. 2 Fig. 3

Supply runs directly to the fixture

Table des matières

Autres manuels Hubbell Changer

Hubbell

Hubbell Reversing Drum Controller 58-GJ2 Manuel

Hubbell

Hubbell iDevices IDEVZ01DW Manuel utilisateur

Hubbell

Hubbell LVS1HD Mode d'emploi

Hubbell

Hubbell CIRCUIT-LOCK Manuel utilisateur

Hubbell

Hubbell Reversing Drum Controller 58-GJ5 Manuel

Hubbell

Hubbell 4211 Manuel d'utilisation et d'entretien

Hubbell

Hubbell Euclid 4220 Manuel utilisateur

Hubbell

Hubbell H-MOSS AP Manuel utilisateur

Hubbell

Hubbell C5027 Manuel

Hubbell

Hubbell Euclid 100E Manuel utilisateur

Hubbell

Hubbell 2243 Manuel utilisateur

Hubbell

Hubbell CIRCUIT-LOCK Series Guide de configuration

Hubbell

Hubbell WL Series Manuel utilisateur

Hubbell

Hubbell CXSW Manuel utilisateur

Hubbell

Hubbell EUCLID Instructions d'installation et d'utilisation

Hubbell

Hubbell Furnas Brand Series 54 Manuel utilisateur

Hubbell

Hubbell 58-GC5026 Manuel

Hubbell

Hubbell M3 Manuel de programmation

Hubbell

Hubbell LUXSTATSW1 Manuel utilisateur

Hubbell

Hubbell Circuit-Lock Manuel utilisateur

Hubbell

Hubbell Euclid PBP Pendant Manuel utilisateur

Hubbell

Hubbell 2200 Manuel utilisateur

Hubbell

Hubbell Euclid 4225 Manuel utilisateur

Hubbell

Hubbell MOTORQUICK Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur