Hubbell Circuit-Lock Manuel utilisateur

HUBBELL CIRCUIT - LOCK™

SAFETY-SHROUD TWIST LOCK®MECHANICAL INTERLOCK REPLACEMENT COVER

Installation Instructions

Wiring Device

Kellems

Hubbell Incorporated (Delaware)

Shelton, CT 06484

1-800-288-6000

www.hubbell-wiring.com

PD2587 (Page 1) 10/13

GENERAL INFORMATION

CAUTION: Risk of electric shock. More than one disconnect switch may be required to de-

energize this equipment before servicing. Disconnect ALL power supplies to enclosure

before exposing interior.

NOTICE: For installation by a qualified electrician in accordance with national and local Electrical

codes and the following instructions.

NOTICE: Receptacle MUST be re-installed BEFORE connection to power supply.

30 Amp Maximum receptacle rating. See ratings table and wiring diagrams.

NOTICE: This enclosure must NOT be used as a junction box for feed-through connections.

NOTICE: Separate overcurrent protection must be provided in accordance with

National Electrical Code® Article 220 or Canadian Electrical Code, Section B, as appropriate.

Overcurrent protection MUST NOT exceed the ampere rating of the receptacle. [Ref. National

Electrical Code®, Part 1, Rule 430-42(c) or Canadian Electrical Code®, Subrule 28-602(3)(c)(i)].

Suitable for use on a circuit capable of delivering not more than 10,000 rms symmetrical amperes at

the voltage rating of the receptacle.

This enclosure includes a lockout provision: ON-OFF control knob (in the OFF position) accepts up

to 5/16 inch (8mm) diameter shackle of a suitable padlock. Lockout device to isolate energy from

the connected equipment as a method of compliance to OSHA Lockout/Tagout Regulation 29 CFR

Part 1910.147. This feature however, does NOT isolate the power supplied to the enclosure during

internal servicing of the enclosure.

MO UNT I NG I NST RUCT I ON S

(1.) Remove the four (4) cover mounting screws and remove the old cover. Switch handle must be

“off” to remove cover.

(2.) Disconnect wiring to receptacle. Remove the four (4) receptacle mounting screws and remove it

from the old cover.

HUBBELL CIRCUIT - LOCK™

SAFETY-SHROUD TWIST LOCK® MECHANICAL INTERLOCK REPLACEMENT COVER

¹VOLTAGE (AC ONLY) AND HORSEPOWER RATINGS ARE DETERMINED BY THE SWITCH BUT MAY BE LIMITED BY

THE AMPERE RATING OF THE RECEPTACLE.

NOTE: “G” designates grounding wire (bare, green or green with yellow stripe)

and yellow and green grounding buss.

“N” designates the blue neutral (grounded) buss.

“W” designates the white neutral (grounded) wire.

(4.) Mount the receptacle to the enclosure cover.

NOTICE: Make sure the lock ring arrows are aligned prior to mounting the receptacle.

Misalignment of the lock ring will prevent insertion of a Safety-Shroud™ Twist-Lock®

plug and will result in improper functioning of the interlock.

NOTICE: Make sure that the lock ring tabs engage the block.

Install the gasket as shown.

Use the four (4) #10 x ¾ inch (19mm) thread-forming screws provided to mount the receptacle

To the cover. Tighten screws to 20 pound·inches (2.4 N·m)

(5.) Reinstall the cover. The handle must be in the OFF position. Make sure the rope gasket is

properly seated in the groove. Tighten the four cover screws to 18 pounds·inches (2.0 N·m).

PD2587 (Page 2) 10

/13

WI RI NG I NST R UCT I ON S

(3.) Refer to the receptacle wiring instructions and re-connect wiring to the receptacle.

Tighten the terminal screws to 18 pound inch (2.0 N•m)

TAKE CAUTI

ON THAT THERE ARE NO

STRAY WIRE STRANDS

Table des matières

Autres manuels Hubbell Enceinte

Hubbell

Hubbell GAI-TRONICS 703-002 Manuel utilisateur

Hubbell

Hubbell Killark USF Series Mode d’emploi

Hubbell

Hubbell GAI-Tronics 703-006 Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 238-001 Series Manuel utilisateur

Hubbell

Hubbell KILLARK B7023 Mode d’emploi

Hubbell

Hubbell GAI-Tronics 758-002 Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 702A Manuel utilisateur

Hubbell

Hubbell GAI-Tronics 707-001-UL Manuel utilisateur

Hubbell

Hubbell GAI-Tronics 708-001-UL Manuel utilisateur

Hubbell

Hubbell GAI-Tronics Smart Series Manuel utilisateur

Hubbell

Hubbell GAI-Tronics 7085-005-UL Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 703A Manuel utilisateur

Hubbell

Hubbell HBLSS26WIS Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 732-101 Manuel utilisateur

Hubbell

Hubbell B2481 Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 733-006 Manuel utilisateur

Hubbell

Hubbell GAI-Tronics 7085-001-UL Manuel utilisateur

Hubbell

Hubbell GAI-TRONICS 7325-101 Manuel utilisateur

Hubbell

Hubbell Killark B7NFD Series Mode d’emploi

Hubbell

Hubbell Killark SJIC Series Mode d’emploi

Hubbell

Hubbell AccelTex ATS-NL-IC-ENC-15153 Manuel utilisateur

Manuels Enceinte populaires d'autres marques

SilentiumPC

SilentiumPC Armis AR5 Manuel

Pulsar

Pulsar 17/TRP80/DSPR Manuel utilisateur

Thermaltake

Thermaltake V150 TG Manuel utilisateur

MSI

MSI MPG SEKIRA 500X Manuel utilisateur

Antec

Antec Dark fleet DF-10 Manuel utilisateur

Nexans

Nexans WTC05 Manuel utilisateur

Peavey

Peavey DS 1502 Manuel utilisateur

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manuel utilisateur

Rosewill

Rosewill RX82-U(JBOD) Manuel utilisateur

QNAP

QNAP SAS JBOD CLI 1.0 Manuel utilisateur

GAMDIAS

GAMDIAS Talos P1 Manuel utilisateur

Auvs

Auvs KR615 Manuel utilisateur

Digitus

Digitus DA-71114 Manuel utilisateur

CommScope

CommScope FDH 3000 Manuel utilisateur

FS FHD-FWME4 Manuel utilisateur

JBL

JBL CS1215T Manuel utilisateur

Pulsar

Pulsar ARAD-S4 Manuel utilisateur

Pulsar

Pulsar AWO454 Manuel utilisateur