Huazheng HZX52AA Manuel utilisateur

HZX52AA

RotaryEvaporator

Huazheng Electric Manufacturing (Baoding) Co., Ltd

Dear use r:

Thank you for cho os in g HZX5 2A A Rot ary Evaporator.

We hope that this instrum ent can mak e your wo rk easier an d mo re

enjoyable, so that you can get the fe el ing of office automat io n in the test

and ana ly si s work.

Before using the instrument, please read thi s ma nu al, and opera te an d

maintain the instru ment ac cord in g to th e manual to pr olong its service li fe.

"Just a lig ht press, the test wi ll be com pl eted auto mati ca lly" is th e

operating chara ct eristi cs of this instrum en t.

If you ar e sat isfied wi th th is instrum en t, please tell you r colleagues;

if you ar e not satisfie d with this instrum ent, please call (03 12 ) 6775656 to

tell you to serve you at all times-Baoding Huazheng Elect ric Manufactu ring

Co. , Ltd., our company will def in itely make you sati sf ied !

Contents

I. Introduction of usage.................................................................................................................... 1

II. Structural features........................................................................................................................1

III. Matters needing attention for use.............................................................................................2

IV. Main technical parameters........................................................................................................ 2

V.Maintenance...................................................................................................................................2

VI. Failure analysis and exclusion methods.................................................................................3

VII. Storage and transportation...................................................................................................... 3

VIII. Accessories............................................................................................................................... 3

IX. Packing List................................................................................................................................. 4

JC-SHZ-III.......................................................................................................................................... 6

Circulating Water Type Vacuum Pump......................................................................................... 7

I.Safety warning................................................................................................................................ 8

II.Function and purpose...................................................................................................................8

IV.Technical index............................................................................................................................. 9

VI.Common faults and troubleshooting methods......................................................................10

VII.Packing list.................................................................................................................................10

Manual for Rotary Evaporator

I. Introduction of usage

Rotary evaporator is a kind of device with the operation principle as follows: put the

rotary evaporation bottle (flask used to increase the evaporation area) in water bath

under the condition of reduced pressure, and make it rotate while heating it, so as to

make the solution in the bottle diffuse and evaporate. It is a relatively ideal basic

instrument necessary for the concentration, drying and recycling relied on by the

production and experimental analysis which is conducted by the chemical industry,

pharmaceutical industry, universities and colleges, and research laboratories and so on.

II. Structural features

1.Rotation of principal machine

Theprincipal machine consists of a group of reliable micro-motors,speed motors and

integrated circuits. Under the action of electronic speed control, it can realize the stepless

speed regulation within the range of 0-150 r / min.

2.Elevation of principal machine

RE-52AA-type principal machine adopting the method of micro-motor speed change

can be automatically ascended and descended only by pressing the switch with hand.

The elevation is

stable, safe and reliable.

3.Tilt of principal machine

The principal machine can be tilted at random within the range of 0-45 ° by loosing plum

blossom screws. The condensate system made of heat-resistant

high-quality glass is connected to the head of principal machine with sockets, thus

making it able to tilt therewith and continuously feed.

4.Heating water tank

Heating water tank is equipped with a closed heating tube with heating wire, and

connected to digital display of temperature, which can automatically connect or disconnect

the power so as to automatically control the water temperature inside the tank.

5.Evaporation pipe

Evaporation pipe uses PTFE, which is corrosion-resistant and can maintain a high

vacuum.

6.Cooler (made of high-quality glass of thermostability, and refined) Vertical, Dual-reflux.

7. Main metal components are made of corrosion-resistant high-quality stainless steel,

thus extending the service life.

III. Matters needing attention for use

1. Please read the Manual and Brief Introduction of Installing Rotary Evaporator first, and

focus on the part of installation preparation, installation procedures and operation.

2. As for the expensive solution, a simulation technology experiment should be conducted

first. Then, the solution can be normally used after confirming the equipment can meet the

experimental requirements.

3. Water temperature inside the water tank will be automatically controlled by the digital

display of temperature.

Accurate water temperature will be measured directly through the mercury thermometer.

4. In case of needing to replace the fuse, the power should be cut off first, followed by

the opening of cover to replace the fuse.

5. When heating the water tank, do not touch with hand to prevent the scald.

6. Can not be used under the environment full of flammable, explosive and narcotic gas.

7. In general, this product does not have specific requirements for disinfection.

IV. Main technical parameters

Capacity of

rotation

bottle

Rotation

speed

Elevation of

principal

machine

Temperature

inside water

tank

Power

supply

50~2000ml

0-150r/min

Power-drive

n elevation

RT-100℃

Digital display

1000W

220v/50Hz

V.Maintenance

1. Glass component: in case of serious dirt, clean it with the dilute sulfuric acid.

2. PTFE connection tube: in general, it needs to be removed and washed only under

serious dirt.

3. The clear water inside the water tank pot should be frequently replaced, with the pot

cleaned.

VI. Failure analysis and exclusion methods

Phenomena

Check (causes)

Handling method

No power supply

1. Check whether the power plug is loose

2. Check whether the fuse is disconnected

1. Insert the power plug tight

2. Replace the fuse

Rotation bottle

shakes or gives

out noise when

Check whether the glass interface of rotation bottle

is installed smoothly and in place

Reinstall the glass interface

and rotation bottle, and screw

and lock the nut tightly.

Insufficient

vacuum

1.Check the performance of vacuum pump, and

whether each connector is tightened (block the air

outlet of vacuum pump to observe the indicators

on vacuum table)

2. Check whether the glass appliances

are defected or cracked for coldness

1.Screwtheconnectors tightly

or replace the vacuum pump

2.Replacethe damaged

appliances

3.Recoat with vacuum

grease

Water tank can

not be heated.

1 Check the 10A fuse

2. Check whether the heating plug is loose

1. Replace the 10A fuse

2. Insert the heating

plug tightly

In case of being unable to troubleshoot according to the above methods,

VII. Storage and transportation

Instruments packed should be stored inside the room, with the temperature within the

range of -10 ~ 40℃, relative temperature not exceeding 90%, non-corrosive gases and

well-ventilated condition. In the process of transportation, they should be free of moisture,

and handled with care.

VIII. Accessories

should be equipped with a 24-port / 250ml rotation bottle and a 500ml ball-milling port

collection bottle.

In case of needing flasks of other specification, the customer should purchase otherwise.

IX. Packing List

No.

Item

Qty

Principal machine(including: control

box, the head, lifting column, base of

principal machine)

Water bath tank (connected to the

right side of principal machine)

Condensation pipe

Collection bottle 500ml

Rotation bottle 250ml

Charging pipe with valves

Stainless steel bracket

Stainless steel bracket circle

Plastic flask clip

Stainless steel ball-milling

Installation:

1. After unpacking, check according to the packing list, clean and dry pieces of glass and

put them in place according to the position of pictures. On the left side should be the body

of principal machine, with the water tank container on the right side.

2. The Rotary evaporator inserts the condenser tube embossing grinding port into the

polytetrafluoroethylene connecting tube on the left side of the head of the main engine

2. the Embossed-grinding mouth on the side of condensation pipe into the PTFE

connection tube on the left side of head of principal machine, and turn back and forth after

inserting tightly to make it to fit well.

3. The condensing tube and collecting bottle are connected with each other, and the joint

is coated with vacuum grease to enhance the sealing performance.

4. Unscrew the black lock nut on the right side of head of principal machine, encase from

the flange of threaded glass joints (see the figure below), and then screw the black lock

nut into the head of principal machine smoothly and tightly.

5. Connect the rotation bottle to the other end of threaded glass joint (Embossed-grinding

mouth), screw on the nut with square rings, and make square rings button the flask rim

closely. In case of needing to back off the rotation bottle, screw off the nut with square

rings to make the bottle exit the Embossed-grinding mouth.

6.Encase collection bottle on the ball-milling mouth of condensation pipe, and clamp

with the clip.

7. Water outlets are connected with rubber tubes for discharge.

8. Vacuum port is connected to the vacuum pump through the vacuum tube.

9. After injecting water into the water tank, the heating plug behind the water tank will be

connected to the power line.

Operation:

1.Power: 220V 50HZ

2. Press the power switch to make it switch on (-), and turn the speed control knob, when

the principal machine will begin to rotate.

3. Press (▲ / ▼) keys, the head of principal machine will ascend or descend

automatically.

4. After injecting water into the water tank, press the heating key (-) and set the

temperature, which can automatically control the heating process. Heating without water

is prohibited.

5. The process of aligning the head angle is as follows: first, loosen the plum blossom

knob on the right side of stand pillar, turn the head of principal machine, and then screw it

tightly after reaching the appropriate angle.

6. After completion of commissioning, power and heating switches will switched to the

state of

Off (0), followed by the unplugging of power plug.

JC-SHZ-III

Circulating Water Type Vacuum

Pump

Huazheng Electric Manufacturing (Baoding) Co., Ltd

Table des matières

Autres manuels Huazheng Instrument de mesure

Huazheng

Huazheng EDEKA TC-200 Manuel utilisateur

Huazheng

Huazheng HZ2831 Manuel utilisateur

Huazheng

Huazheng HZ1434 Manuel utilisateur

Huazheng

Huazheng CS2670A Manuel utilisateur

Huazheng

Huazheng HZDZ-S3 Manuel utilisateur

Huazheng

Huazheng HZ-600A Manuel utilisateur

Huazheng

Huazheng HZSM-701 Manuel utilisateur

Huazheng

Huazheng HZ-8700 Manuel utilisateur

Huazheng

Huazheng HZSF-801 Manuel utilisateur

Huazheng

Huazheng HZCT-100B Manuel utilisateur

Huazheng

Huazheng HPC500 Manuel utilisateur

Huazheng

Huazheng PHS-2F Manuel utilisateur

Huazheng

Huazheng HZSF-641 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur