Huawei UPS5000-E-50K-HABBS Manuel utilisateur

Issue: 01

Part Number: 31500DXL

Date: 2020-04-13

UPS5000-E-(60 kVA–125 kVA)

Quick Guide (Integrated UPS 3.0)

UPS Model Capacity

Configuration

Weight (Full

Configuration) Dimensions (H x W x D)

UPS5000-E-50K-HABBS 30 kVA, 60 kVA 352 kg

2000 mm x 600 mm x

1100 mm

UPS5000-E-50K-HASBS 390 kg

UPS5000-E-125K-HABBS-01 90kVA, 120kVA,

125kVA

435 kg

UPS5000-E-125K-HASBS-01 453 kg

•The appearance of the UPS5000-E-60K-HABBS (02312TVW, 02312TWB) is similar to that of

the UPS5000-E-125K-HABBS-01 (02312TVY, 02312TWC).

•The appearance of the UPS5000-E-60K-HASBS (02312TVX) is similar to that of the UPS5000-

E-125K-HASBS-01 (02312TWA).

•If Requisite modules is set to 5, the maximum output capability of each module is 25 kVA/25 kW.

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation.

3. Only engineers certified by Huawei or its agents are allowed to install, commission, and

maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS

faults caused are beyond the warranty scope of Huawei.

UPS5000-E-125K-HASBS-01

(1) Power input

status indicator

(2) ATS

(3) Lighting

circuit breaker

(4) ATS handle

installation slot

(5) Power distribution

circuit breaker for the

mart cooling product

(6) IT load circuit

breaker

(7) UPS input

circuit breaker

(8) UPS maintenance

bypass circuit breaker

(9) Control

module

(10) Bypass module

(11) Power module

(12) Monitor display unit

(MDU)

(13) Power distribution

monitoring board

(14) UPS output

circuit breaker

UPS5000-E-60K-HABBS

(1) Power input

status indicator

(2) Input circuit

breaker

(3) Lighting

circuit breaker

(4) Power distribution

circuit breaker for the

mart cooling product

(5) IT load circuit

breaker

(6) UPS input

circuit breaker

(7) UPS maintenance

bypass circuit breaker

(8) Control module

(9) Bypass module

(10) Filler panel

(11) Power module

(12) Monitor display unit

(MDU)

(13) Power distribution

monitoring board

(14) UPS output

circuit breaker

2Installing the UPS

1. Determine the mounting holes based on the marking-off template, drill holes, and install expansion

sleeves (unit: mm).

3. Secure the UPS.2. Adjust the anchor bolts and ensure that the

anchor bolts touch the floor. Then level the

UPS.

2. Secure the tail frame upper sealing plate to

the tail frame.

3(Optional) Installing the Tail Frame

1. Secure the tail frame fittings to the tail frame.

There are two upper sealing plates, and the

one used in this step has a gap.

3. Remove the rear door of the cabinet, hinges,

connecting plates, and ground cable. 4. Adjust the tail frame anchor bolts until the tail

frame is as high as the cabinet. Then secure

the tail frame to the UPS.

5. Install the hinges, connecting plates, and rear door on the tail frame.

6. Connect the ground cable to the rear door of the cabinet.

4(Optional) Combining Cabinets

The figures are for reference only. The actual product appearance prevails.

2. Remove the cabinet connecting kits from

the rack.

3. Secure the connecting kits in the

connection positions on the front door

using screws.

1. Open the front and rear doors. Wrench the

anchor bolts using an wrench to adjust the

cabinet height. Use a level to level the cabinet.

4. Use the same method to secure the

connecting kits in the connection

positions on the rear door.

5Connecting Cables

5. Repeat the procedure to combine other cabinets.

6. Secure the bolts using a socket wrench.

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinet in a timely manner. Ensure that there is no

foreign matter inside and around the cabinet.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

Remove the screw from the supporting kit

of the connecting kit to secure the

connecting kit.

UPS Cable Connection Reference

5.1

Connecting Power Cables

3.2

Scenario 1: Routing Cables from the Top

The cabling route is for reference only. Connect cables based on site requirements.

1. Remove the insulation protective panel from

the rear of the cabinet and remove covers

from the top as required.

2. Connect a ground cable to the UPS cabinet.

ATS input

3. Connect the AC input power cable.

MCCB input

4. Connect battery cables, AC output power cables, fire protection cables and generator Start/Stop

cables. Neutral cables

Battery cables PE cables

IT and smart cooling product output power

cables

Lighting cables

Fire Protection and Generator

Start/Stop Cables (ATS input cabinet)

Port Description Bolt Specifications Bolt Length Torque

AC input M12 45 mm 46 N·m

Battery input M10 30 mm 26 N·m

PE M12 45 mm 46 N·m

Safe grounding M6 16 mm 4.5 N·m

Route a neutral wire from the middle of the

positive and negative battery strings.

Take a battery string consisting of 40 batteries

as an example. A neutral wire is routed from the

middle of positive and negative battery strings,

each consisting of 20 batteries.

•Cables can be routed in and out from the bottom only when a tail frame is configured for the

cabinet.

•This section uses the ATS cabinet as an example. For details about cable connections in other

cabinets, see the procedure in this section.

•Connect the inside cables first, and then the outside cables.

1. Remove the cover plate from the cable hole

at the bottom of the tail frame.

2. Remove the insulation panels at the rear of

the cabinet.

3. Connect a ground cable to the safety ground

of the UPS cabinet.

4. Connect AC input power cables.

Scenario 2: Routing Cables from the Bottom

5. Connect the battery cable and ground cable

of the cabinet. 6. Connect AC output power cables.

Connecting Communications Cables

5.2

The following figure uses cable routing from the top as an example.

Lighting wiring

terminal

Smart cooling

product wiring

terminal

IT wiring terminal

Connect a communications cable between the FE port on the UPS monitoring interface card and

any PoE port on the ETH gateway.

Connecting CommunicationsCables to Northbound Devices

ETH gateway

6Verifying the Installation

1. Check that there is no foreign matter at the top and bottom of the cabinet, copper bars, switches,

and the rear of modules.

(Optional) ConnectingSmartLi

Communications Cables

Connect one end of the cable to the COM1

port on the UPS monitoring interface card, and

connect the other end to the COM port on the

SmartLi monitoring interface unit.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Huawei UPS

Huawei

Huawei PDU8000 Series Manuel utilisateur

Huawei

Huawei UPS5000-A-400K-FTS Manuel utilisateur

Huawei

Huawei UPS5000-E-25K-SM Manuel utilisateur

Huawei

Huawei SUN2000-4.95KTL-JPL0 Manuel utilisateur

Huawei

Huawei SmartLi Series Manuel utilisateur

Huawei

Huawei UPS5000-E-****-FM series Manuel utilisateur

Huawei

Huawei PDU8000 Series Manuel utilisateur

Huawei

Huawei UPS2000-A-6KTTS-S Manuel utilisateur

Huawei

Huawei UPS2000-G-6 kVA Manuel utilisateur

Huawei

Huawei UPS5000-S-300 kVA Manuel utilisateur

Huawei

Huawei UPS5000-E-600K-SC Manuel utilisateur

Huawei

Huawei UPS5000-H-600 kVA-FTN Manuel utilisateur

Huawei

Huawei UPS2000-A-6 kVA Manuel utilisateur

Huawei

Huawei UPS5000-H Series Manuel utilisateur

Huawei

Huawei PDC-0038V4ACIOA-V2 Manuel utilisateur

Huawei

Huawei UPS5000-H-800 Manuel utilisateur

Huawei

Huawei UPS5000-S Series Manuel utilisateur

Huawei

Huawei UPS5000-E Series Manuel utilisateur

Huawei

Huawei iSitePower-M Manuel utilisateur

Huawei

Huawei UPS5000-E-40 kVA Manuel utilisateur

Huawei

Huawei PDU8000 Series Manuel utilisateur

Huawei

Huawei UPS2000-G-3K-V1-DR Manuel utilisateur

Huawei

Huawei UPS5000-E Series Manuel utilisateur

Huawei

Huawei UPS5000-E Series Manuel utilisateur

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur