HP StorageWorks EVA4000 Mode d’emploi

HP StorageWorks

Fibre Channel Disk Drive

Replacement Instructions

These instructions apply to the EVA

4000/6000/8000 product family. The part

may also be used in other HP products. Please refer to

documentation for your speciﬁc product for detailed

replacement instructions.

Printed on at least 50% total recycled ﬁber with at least

10% post-consumer paper.

First edition April, 2005

Product names mentioned herein may be trademarks of their

respectivecompaniesasreﬂected by an associated footnote.

The information in this document is subject to change without

notice.

Printed in the U.S.A.

www.hp.com

*5697-5248*

Warranty Information

If the product in which this part is being replaced is still under

HP warranty, then the replacement part(s) referred to in these

Replacement Instructions is provided under the terms and conditions

of the Hewlett-Packard Company Limited Warranty for that

product. A copy of this Limited Warranty may be viewed at:

http://h18006.www1.hp.com/products/storageworks/warranty.html

If this is a trade sale part (product out of warranty), then the replacement

part(s) referred to in these Replacement Instructions is provided under

HP's express limited warranty statement, which may be viewed at:

http://customerops.corp.hp.com/1sw/pdm_om/warranty_support/

policies/2330100.doc

The replacement part takes on either the Limited Warranty Period of the

part being replaced or a ninety-day period that begins upon installation

of the replacement part, whichever is greater.

The only warranty for this replacement product is as noted above.

Nothing in these replacement instructions should be construed as

constituting an additional warranty. The information provided in these

replacement instructions is provided "AS IS" and HP is not liable for

technical or editorial errors or omissions contained herein.

1 About This Document

This document describes the procedure for replacing the Fibre Channel

disk drive used in the EVA 4000/6000/8000 products.

2 Before you begin

Observe the following precautions when replacing the disk drive.

CAUTION:

Make sure you have a replacement part available before

removing the failed component. Removing a component

impacts cooling within the enclosure.

Do not remove more than one disk drive at a time from the

enclosure. Doing so will impact cooling of the enclosure

and may cause data loss.

Parts can be damaged by electrostatic discharge. Use

proper anti-static protection. Refer to the documentation that

shipped with your system for additional information.

Have a copy of the product User Guide available for

reference. You can download a copy of the User Guide

from the product support page on the HP web site.

3 Verifying component failure

Before replacing a disk drive, use the following methods to verify the

component failure:

CAUTION:

IfCommandViewEVAdoesnotpresentastatusconsistent

with that of the disk drive status indicators, or if Command

View or the System Event Analyzer indicates multiple

hardware failures, contact HP support for assistance. The HP

support web site is located at http://www.hp.com/support

Page 1

•Analyze any failuremessagesyoumayhavereceivedfromsystem

monitoring (System Event Analyzer).

•Check the disk drive status indicators. See Figure 1.TheFault

indicator should be On.

•Check status using Command View EVA:

1. In the Navigation pane, select Storage system > Hardware >

Rack > Disk enclosure > Bay

2. In the Content pane, select the Disk Drive tab. The Operational

state should be Failed .

3. Verify the following status conditions are met before proceeding:

• Migration state - Not migrating

• Requested usage - Ungrouped

•Actualusage-Ungrouped

4. Click Remove to prepare the disk for removal. The status

indicators on the disk drive will begin ﬂashing to help you

locate the disk.

123

Figure 1 Disk drive status indicators

1. Activity 2. Online 3. Fault

4 Removing a disk

CAUTION:

Rotating media can make the disk drive difﬁcult to handle.

To avoid dropping and damaging the disk drive, wait

approximately 30 seconds for the media to stop rotating

before removing the drive from the enclosure.

1. Push in the wine-colored ejector button (1) and pull the release

lever (2) down to the full open position.

2. Pull the disk drive part way out of the enclosure (3) and wait for the

media to stop spinning.

3. When the media has stopped spinning, remove the disk drive from

the enclosure.

0115a

Figure 2 Removing a disk drive

5Installingadiskdrive

1. Push in the ejector button on the disk drive and pull the release

lever down to the full open position.

2. Insert the drive into the enclosure as far as it will go (1).

3. Close the release lever until it engages the ejector button, and the

disk drive seats in the backplane (2).

4. Press in ﬁrmly on the disk drive to ensure it is seated properly.

0116a

Figure 3 Installing a disk drive

Page 2

6 Verifying proper operation

After replacing the disk drive, check the following to verify that the

disk drive is operating normally:

NOTE:

Itmaytakeupto10minutesforthecomponenttodisplay

good status.

•Check the disk drive status indicators. See Figure 1.

•Activityindicator(1)shouldbeonorﬂashing

• Online indicator (2) should be on or ﬂashing

• Fault indicator (3) should be off

•Check the following using Command View EVA.

• Navigate back to the component and check the operational

state. It should be

• Ensure the disk drive is using the correct ﬁrmware. Check the

Firmware Version against the supported disk ﬁrmware in the HP

StorageWorks Enterprise Virtual Array Release Notes.Themost

current edition of the release notes can be downloaded from the

following web site:http://www.hp.com/go/eva8000

If the disk drive is using an unsupported version of ﬁrmware,

contact HP support for assistance. Do not add the disk drive to a

disk group if it using an unsupported ﬁrmware version.

7 Adding the disk to a disk group

After replacing the disk, it should be added to a disk group. The disk is

typically added back into its original disk group.

1. In the Navigation pane, select Storage system > Hardware > Rack

>Diskenclosure>Bay

2. In the Content pane, select the Disk Drive tab.

3. Click Group to initiate the process for adding the disk to a disk

group.

NOTE:

If the Device Addition Policy is set to automatic, the disk will

automatically be added to a disk group. In this case the

Group option will not be available.

8Returningthe failed component

Please follow the return instructions provided with the new component.

Page 3

Ce manuel convient aux modèles suivants

Autres manuels HP Stockage

HP 20 MODULAR SMART ARRAY Manuel utilisateur

HP Surestore 160ex - Optical Jukebox Manuel utilisateur

HP ProLiant SB460c - SAN Gateway Storage Server Manuel utilisateur

HP StorageWorks 400r All-in-One Instructions d'utilisation

HP Brio 71xx Manuel utilisateur

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP Surestore E Tape Library Model 2/20 Manuel utilisateur

HP Xw4600 - Workstation - 2 GB RAM Manuel utilisateur

HP StorageWorks DAT 72 Instructions d'utilisation

HP StorageWorks DLT 80 Instructions d'utilisation

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Manuel utilisateur

HP AJ765A - StorageWorks RDX Removable Disk Backup... Mode d’emploi

HP ProLiant StorageWorks NAS 1500s Manuel utilisateur

HP ESL E-Series Manuel utilisateur

HP PD5000Z Manuel utilisateur

HP StorageWorks P2000 Manuel utilisateur

HP StorageWorks 1510i - Modular Smart Array Mode d’emploi

HP StorageWorks NAS b2000 - v2 Manuel utilisateur

HP StorageWorks 12000 Manuel utilisateur

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Instructions d'installation et d'utilisation

HP StorageWorks P2000 Manuel utilisateur

HP C1533A Guide de configuration rapide

HP StorageWorks Disk System 2405 Manuel d'utilisation et d'entretien

HP Surestore Disk Array 12h - And FC60 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur