HP NetServer e 800 Manuel utilisateur

HP Part Number D9394-90000

Printed June 2000

HP NetServer E 800

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

Intel®and Pentium®are registered trademarks of Intel Corporation. Microsoft®,

Windows NT®, Windows 95®and Windows 2000®are registered trademarks of

Microsoft in the U.S. and other countries. Novell®and NetWare®are registered

trademarks of Novell, Incorporated in the U.S. and other countries. Symantec®is a

registered trademark of Symantec, Incorporated. pcANYWHERE32™ is a trademark

of Symantec, Incorporated. Torx®is a registered trademark of CamCar/Textron,

Incorporated.

Hewlett-Packard Company

Network Server Division

Technical Communications / MS 45SLE

10955 Tantau Avenue

Cupertino, California 95014 USA

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

Setting Up the HP NetServer E 800................................................................. 1

Introduction ................................................................................................... 1

Step 1: Attaching all the Cables................................................................. 2

Step 2: Opening the HP NetServer............................................................ 3

Step 3: Installing Memory.......................................................................... 5

Step 4: Installing Mass Storage Devices.................................................... 6

Step 5: Installing Adapter Boards............................................................. 10

Step 6: Installing a Second Processor ..................................................... 14

Step 7: Configuring the HP NetServer..................................................... 19

Setting Up the HP NetServer E 800

Introduction

This installation guide is a quick reference for HP NetServer E 800 installation.

Skip any steps that do not apply to your installation. Refer to the figures below

for connection and operating information. For more information, refer to the

HP NetServer E 800 User Guide.

Flexible

Disk Drive

CD-ROM Drive

Power ON/OFF/

Sleep Switch

Power ON/

OFF/Sleep LED

SCSI Drive

Activity LED

Optional Back-Up

Tape Drive

Power

Mouse

Keyboard

USB(2) LAN

Serial A

Parallel

Serial B

Video

(SVGA)

Key Lock

External SCSI

(Optional)

Fold-Out

Feet (4)

Unlocked Position

Locked Position

Setting Up the HP NetServer E 800

Step 1: Attaching all the Cables

If you are not installing any accessories, attach all available cables to the

respective connectors, then go to "Step 7: Configuring the HP NetServer."

NOTE The two USB connectors are reserved for printers, scanners,

and external modems. The NetServer does not support USB

connections for the keyboard and mouse.

Power

Power Cord

Strain Relief

Mouse

Keyboard

Video

SVGA

LAN

Setting Up the HP NetServer E 800

Step 2: Opening the HP NetServer

Tools Required:

•¼ inch flat-blade screwdriver

•Torx T-15 driver

WARNING Before removing the cover, always disconnect the power cord

and remove the telephone cable.

Disconnect the power cord to avoid exposure to high energy

levels that may cause burns when parts are short-circuited by

metal objects such as tools or jewelry. Disconnect telephone

cables to avoid exposure to shock hazard from telephone

ringing voltages.

Key-

Lock

Slotted

Thumbscrews(6)

Setting Up the HP NetServer E 800

Front of Chassis

Bottom of Chassis

Cover

Latch Opening

Air Duct

Latch

Setting Up the HP NetServer E 800

Step 3: Installing Memory

•Use only HP DIMMs, which are 3.3V, 168-pin, PC133 (133 MHz),

buffered SDRAM DIMMs in 128 MB, 256 MB, or 512 MB.

•DIMMs may be installed in any slot, in any combination (sizes mixed), in

any order, but HP recommends starting at slot 0 and filling the slots in

order with the largest size first: 0, 1, 2, and 3.

•Ensure both latches close on the DIMM when completely installed.

System Board

0123

Retaining Latches

DIMM Slot

Keys

Notches

Setting Up the HP NetServer E 800

Step 4: Installing Mass Storage Devices

•The NetServer is internally limited to 7 mass storage shelves.

The flexible disk drive and CD-ROM drive, which are standard on all

models of the HP NetServer E 800, occupy shelves 1 and 2 respectively.

•If a backup tape drive is used, it will occupy shelf 3.

•Shelves 4, 5, 6, and 7 are available for up to four SCSI hard drives and at

least one is required for the boot drive.

•IDE drives are not supported in this NetServer.

CAUTION Do not connect high voltage differential (HVD) SCSI devices

on the SCSI bus or you will damage the other devices.

1. Remove the Drive Cage by loosening the three captive screws.

Top of Chassis (Side view)

Captive Screws (3)

Front of

HP NetServer

Hard Disk

Drive Cage

(removable)

Shelf 1

Shelf 2

Shelf 3

Shelves 4-7 (4)

2. Install the SCSI hard disk drive.

Autres manuels pour NetServer e 800

Table des matières

Autres manuels HP Serveur

HP ProLiant BL660c Manuel utilisateur

HP ProLiant BL2x220c G7 Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

HP NetServer e 800 Manuel utilisateur

HP ProLiant DL585 Guide de démarrage rapide

HP Cluster Platform Introduction v2010 Manuel de service

HP t5325 - Thin Client Manuel utilisateur

HP ProLiant BL490c Manuel utilisateur

HP Compaq t5515 Manuel de service

HP Integrity rx2620 Manuel utilisateur

HP ProLiant SL2x170z - G6 Server Manuel

HP ProLiant DL280 Manuel

HP ProLiant DL320e Gen8 v2 Manuel utilisateur

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Manuel utilisateur

HP HPE XL270d Instructions d'installation

HP DesignJet T610 Manuel utilisateur

HP t5400 - Thin Client Manuel utilisateur

HP 9000 rp4410 Manuel utilisateur

HP ProLiant ML110 Gen9 Manuel utilisateur

HP D7171A - NetServer - LPr Manuel utilisateur

HP BL35p - ProLiant - 2 GB RAM Manuel utilisateur

HP T5735 - Compaq Thin Client Manuel de service

HP D7171A - NetServer - LPr Manuel utilisateur

HP HPE ProLiant ML30 Gen9 Manuel

Manuels Serveur populaires d'autres marques

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Dell

Dell PowerEdge HS5610 Manuel