HP D7171A - NetServer - LPr Manuel utilisateur

HP NetServer LC 2000

Pedestal to Rack Guide

HP Part Number 5969-2110

Printed November 1999

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced,

or translated to another language without the prior written consent of

Hewlett-Packard Company.

Windows NT®, Windows 95®, and Windows 98®are registered trademarks of

Microsoft in the U.S. and other countries.

3M®is a registered trademark of Minnesota Mining and Manufacturing Company.

Torx®is a registered trademark of CamCar/Textron, Inc.

Tinnerman®is a registered trademark of Eaton/Tinnerman.

Hewlett-Packard Company

Network Server Division

Technical Communications MS 45SLE

10955 Tantau Avenue

Cupertino, California 95014 USA

Audience Assumptions

The guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels and are familiar with weight and stability precautions for

rack installations.

iii

Contents

1 Preparing the HP NetServer for Rack-Mounting ........................................ 1

Introduction ................................................................................................... 1

Tools Required.......................................................................................... 1

Removing the HP NetServer’s Top Cover and Pedestal................................. 2

Removing the Bezel .................................................................................. 3

Removing the Top Cover........................................................................... 4

Removing the Pedestal.............................................................................. 5

2 Rack Mounting the HP NetServer ............................................................... 7

Introduction ................................................................................................... 7

Tools Required.......................................................................................... 8

Safety Precautions.................................................................................... 9

Preparing the Rack...................................................................................... 10

HP NetServer Rack Mount Parts List....................................................... 10

Marking the Rack and Attaching Rack Nuts ............................................. 10

Attaching the Column Adapters and Slides.............................................. 13

Attach the Hinge Assembly and Catch Assembly..................................... 16

Attach the Mounting Handles................................................................... 17

Placing the HP NetServer in the Rack...................................................... 18

Attaching the Cable Management Arm..................................................... 22

Attaching the Front Bezel ........................................................................ 24

Continuing with the Rack Installation Process.............................................. 25

Index............................................................................................................... 27

1 Preparing the HP NetServer for

Rack-Mounting

Introduction

This chapter describes how to remove the top cover and the pedestal from the

HP NetServer LC.

WARNING Before removing the top cover, shut down the operating

system and disconnect the power cords and unplug telephone

cables. Disconnect the power cords to avoid exposure to

high energy levels that may cause burns when parts are

short-circuited by metal objects, such as tools or jewelry.

Disconnect telephone cables to avoid exposure to a shock

hazard from telephone ringing voltages.

Tools Required

An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit

includes a static-dissipating work surface, a chassis clip lead, and a wrist

strap.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the HP NetServer’s Top Cover and

Pedestal

Use this procedure to remove the bezel, top cover, and pedestal from the pedestal

version of the HP NetServer LC 2000.

WARNING Do not operate the HP NetServer with its covers removed.

Always disconnect the power cord before removing any

covers, to avoid exposure to high energy levels that may cause

burns when parts are short-circuited bymetal objects such as

tools or jewelry. Disconnect any telephone cables to avoid

exposure to shock hazard from telephone ringing voltages.

CAUTION To prevent overheating, never operate the NetServer with its

cover removed. This includes the power supplies and Hot

Swap hard disks, which must be replaced or the opening

covered immediately (within 2 minutes).

1. If the HP NetServer is operating, log off all users and if necessary back-up

files.

2. Follow instructions in your network operating system (NOS)

documentation to gracefully shut down all networking software and

applications.

3. Press the power switch on the HP NetServer’s control panel when

prompted by the operating system.

Normally, this completes the power down procedure.

4. Disconnect the power cord from its power source.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Bezel

1. Pull the top of the bezel forward until it unsnaps.

2. Lift the entire bezel upward and away from the chassis. See Figure 1-1.

The bezel connects to the front of the HP NetServer chassis with two snap-in

connectors at the top front of the chassis and two metal tabs, which fit into

two slots on the bottom front of the chassis.

Figure 1-1. Removing the HP NetServer LC 2000 Bezel

CAUTION To prevent damage to the covers, support the cover as you

remove it from the HP NetServer. The NetServer’s covers can

be easily damaged.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Top Cover

1. Remove the single screw that secures the top cover to the front of the

NetServer.

2. Slide the top cover forward to disengage the mounting brackets.

3. Lift the top cover off (See Figure 1-2).

Screw Hole

Top Cover

Figure 1-2. Removing the Top Cover

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Pedestal

The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal,

which can be easily removed, if necessary.

NOTE The front bezel is shown removed, but the bezel may remain on

the chassis while removing the pedestal.

1. Disconnect all cables connected to the rear of the NetServer that would

limit its rotation before continuing.

2. Turn the NetServer over onto its top and pull up on the two tabs as shown

in Figure 1-3.

Figure 1-3. Removing the Pedestal

3. Slide the pedestal to the rear of the NetServer as shown in Figure 1-3.

Autres manuels pour D7171A - NetServer - LPr

117

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Serveur

HP t310 G2 Instructions d'installation

HP ProLiant SL6000 Manuel utilisateur

HP DL385 - ProLiant - G5 Instructions d'utilisation

HP ProLiant SL270s Generation 8 Instructions d'utilisation

HP Integrity BL860c Mode d’emploi

HP Apollo 2000 System Manuel utilisateur

HP cc2300 Manuel

HP ProLiant DL185 Instructions d'utilisation

HP gt7720 - Thin Client Manuel utilisateur

HP ProLiant BL495c G6 Manuel utilisateur

HP BL460c - ProLiant - G5 Instructions d'utilisation

HP PROLIANT ML350 G6 Manuel utilisateur

HP D7171A - NetServer - LPr Manuel utilisateur

HP ML570 - ProLiant - G2 Instructions d'utilisation

HP DL385 - ProLiant - G5 Instructions d'utilisation

HP PA-8600 Manuel utilisateur

HP ProLiant ML310e Manuel utilisateur

HP t5740 - Thin Client Manuel de la liste des pièces

HP RP7405/7410 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

HP ProLiant BL40p Manuel

HP DL360 - ProLiant - Photon Manuel utilisateur

HP vc4815 - Thin Client Manuel utilisateur

HP DL385 - ProLiant - G5 Instructions d'utilisation

Manuels Serveur populaires d'autres marques

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Dell

Dell PowerEdge HS5610 Manuel