HP PS1810-8G Manuel utilisateur

HP PS1810 Switch

Installation and Getting Started Guide

HP PS1810-8G (J9833A)

HP PS1810-24G (J9834A)

Power over Ethernet PD

HP PS1810 Switches

Installation and Getting Started Guide

The information contained herein is subject to change without notice.

This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied,

reproduced, or translated into another language without prior written consent of Hewlett-Packard.

Manual Part Number

5998-4329

June 2013

Applicable Products

HP PS1810-8G (J9833A)

HP PS1810-24G (J9834A)

Safety

Before installing and operating this product, please read the “Installation precautions” in Chapter 2, “Installing the switch”, and the safety

statements in General Safety and Regulatory Information booklet included with the product.

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and

services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors

or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.

Warranty

For the latest license and warranty information, see www.hp.com/support/networking-warranties.

For a copy of the warranty terms specific to your HP products, contact an HP authorized dealer or the HP Sales and Service Office in

your country/region.

Contents

1 Switch overview

Switch hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Network ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Reset button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Clear button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

Switch features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2 Installing the switch

Included parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Installation precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

1. Prepare the installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2. Mount the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

3. Connect the network cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14

4. Power on the switch and verify that self-test completes normally . . . . 2-15

SFP installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18

Connections to HP ProLiant Gen8 Servers . . . . . . . . . . . . . . . . . . . . . . . . 2-19

3 Configuring the HP PS1810 Switches

Initial configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Managing the switch via the 192.168.2.10 address . . . . . . . . . . . . . . . . . . . . . . 3-3

Restoring DHCP addressing to the switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Next steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

4 Troubleshooting

Basic troubleshooting tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Diagnosing with the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Diagnostic tips: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Testing the switch by resetting it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Restoring to factory defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Before calling support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

A Specifications

Switch Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

Cabling and Technology Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Cabling Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4

Technology Distance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5

Mode Conditioning Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

Installing the Patch Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6

Twisted-Pair Cable/Connector Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-8

Straight-through Twisted-Pair Cable for

10 Mb/s or 100 Mb/s Network Connections . . . . . . . . . . . . . . . . . . . . . . A-10

Crossover Twisted-Pair Cable for

10 Mb/s or 100 Mb/s Network Connection . . . . . . . . . . . . . . . . . . . . . . . A-11

Straight-Through Twisted-Pair Cable for

1000 Mb/s Network Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12

B EMC Regulatory Statements

Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Index-1

1-1

Switch overview

The PS1810-8G and PS1810-24G switches are multiport managed gigabit switches

that enable you to build high-performance switched workgroup networks and to work

with HP ProLiant Gen8 Servers. These switches are store-and-forward devices that

offer low latency for high-speed networking.

Throughout this manual, these switches are referred as the PS1810-8G and PS1810-

24G Switches.

■The PS1810-8G Switch has 8 auto-sensing 10/100/1000BASE-T RJ-45 ports.

Port 1 is a Power over Ethernet Powered Device (PoE PD) port. The switch can

be powered by a network connection to port 1 from PoE power sourcing

equipment (PSE), such as a PoE switch.

■The PS1810-24G Switch has 24 auto-sensing 10/100/1000BASE-T RJ-45 ports

and two SFP slots (ports 25 and 26) for supported HP SFP fiber-optic

transceivers.

■The PS1810-8G switch has a unique enclosure that allows physical stacking on

the HP ProLiant MicroServer Gen8 product.

You can connect these switches directly to computers, printers, and servers to provide

dedicated bandwidth to those devices, and you can build a switched network

infrastructure by connecting these switches to hubs, other switches, or routers. The

PS1810 switches have the built-in technology that reports real-time health status for

each Gen8 Server in the network. In addition, these switches offer limited network

management capabilities as well.

1-2

Switch overview

Switch hardware

HP PS1810-8G (J9833A)

Link/Act and Speed LEDs

10/100/1000BASE-T RJ-45 ports1

Fault LEDs

Reset and Clear buttons

PoE PD port

1 All RJ-45 ports have the Auto-MDIX feature.

Power

LEDs

Power connector

PD Status

LEDs

1 All RJ-45 ports have the Auto-MDIX feature.

HP PS1810-24G (J9834A)

Link/Act and Speed LEDs

10/100/1000BASE-T RJ-45 ports1SFP slots

Power, Fault, and

Locator LEDs

Reset and Clear buttons

The back of the PS1810-24G has the AC power connector.

1-3

Switch overview

Switch hardware

Network ports

■Auto-sensing 10/100/1000BASE-T ports.

These ports support the “Auto-MDIX” feature, a feature that allows you to use

either straight-through or crossover twisted-pair cables to connect network

devices to the switch.

■PoE PD port (PS1810-8G Switch only)

A network connection to the PoE PD port from a PoE PSE device can provide

power to the switch.

■SFP slots for fiber or copper uplinks (PS1810-24G Switch only). SFPs support

the following network connectivity:

Optional Network Connectivity, Speeds, and Technologies

Speed Technology Cabling SFP Connector1

100 Mb/s 100-FX Fiber (multimode) LC

1 Gbps

1000-T Copper (twisted-pair) RJ-45

1000-SX Fiber (multimode) LC

1000-LX Fiber (multimode or single mode) LC

1To get information about the supported transceivers, see www.hp.com/networking/

support.

1. In the Auto Search textbox, type J4858 (for 100-Mb and Gigabit information).

2. Select one or more products that are displayed in the list. Click Display selected.

3. Click Product support information. The support page opens. In the support page, click

Manuals and find the Transceiver Support Matrix.

For technical details of cabling and technologies, see "Cabling and Technology Information"

in Appendix A.

1-4

Switch overview

Switch hardware

LEDs

The front and back panels of the switches provide status LEDs for system monitoring.

The following table lists the functions of the various indicators.

LED State Meaning

Power

(green)

On The switch is receiving power.

Off The switch is not receiving power.

Fault

(orange)

On On, after the switch is powered on or reset, at the beginning of switch self test. If

the LED remains on, it indicates a detected hardware failure during the self test.

Blinking* Indicates a fault condition on the switch or one of the switch ports. The Link LED

for the port with the fault blinks simultaneously.

Off The normal state; indicates that there are no fault conditions on the switch.

Locator

(blue)

PS1810-24G

Switch only

Blinking** The Locator LED helps you locate a specific switch in an area full of switches. The

LED blinks for 30 minutes when activated through the switch software.

Off The Locator LED is disabled by default.

(green)

PS1810-8G

Switch only

On Power is available on the PoE In port (Port 1).

Blinking* Power is no longer available on the PoE In port. The switch is powered from the

external power adapter. The LED continues to blink until power is restored on the

PoE In port or the switch is reset.

Off Power is not available on the PoE In port.

Link/Act

(green)

On The port is enabled and receiving a link indication from the connected device.

Off One of these conditions exist:

• An active network cable is not connected to the port.

• The port is not receiving link beat or sufficient light.

• Green Mode is enabled.

Blinking* Indicates that there is network activity on the port.

Spd

(green)

On Indicates the port is operating at 1000 Mb/s.

Blinking Indicates the port is operating at 100 Mb/s.

Off Indicates the port is operating at 10 Mb/s.

* The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

** The blinking behavior is an on/off cycle once every 0.8 seconds, approximately.

Autres manuels pour PS1810-8G

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Routeur réseau

HP A8800 Series Manuel d'installation

HP HPE 1820 Switch Series Manuel utilisateur

HP 5500 HI Series Manuel utilisateur

HP MSR954 Series Manuel utilisateur

HP MSR930 Series Instructions de montage

HP FlexNetwork HSR6600 Manuel utilisateur

HP FlexNetwork MSR3044 Instructions de montage

HP FlexNetwork MSR 954 Manuel utilisateur

HP N1200 - StorageWorks Network Storage Router Manuel utilisateur

HP MSR2000 Series Manuel utilisateur

HP J3138A Manuel utilisateur

HP FlexNetwork MSR Series Manuel utilisateur

HP MSR930 Series Manuel utilisateur

HP MSR20-10 Manuel utilisateur

HP Fax 650 Manuel utilisateur

HP 7000dl Series Instructions d'utilisation

HP Pavilion a6600 Manuel utilisateur

HP N1200 - StorageWorks Network Storage Router Manuel

HP Pavilion 8800 - Desktop PC Manuel utilisateur

HP A-MSR900 Series Manuel utilisateur

HP A6616 Manuel utilisateur

HP StorageWorks MPX200 Manuel de programmation

HP StorageWorks MPX200 Mode d’emploi

HP 12500 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité