HP ProCurve J9065A Manuel utilisateur

ProCurve Network Access

Controller 800

Revision 1.0

Quick-start Guide

Central Management

Quick-start Card-2

Central Management

NAC 800 uses clusters and servers. A cluster is a logical grouping of one or

more Enforcement servers (ESs) that are managed by one Management server

(MS).

The quarantine method is defined per cluster; all of the Enforcement servers

in a given cluster use the same quarantine method (Inline, DHCP, or 802.1X).

When using multiple clusters, each cluster can have a different quarantine

method. Clusters cooperate to test and control access to the network.

Physical Deployment

NAC 800 installs in one of the following ways:

■Inline – When deploying NAC 800 inline, NAC 800 monitors and

enforces all device traffic. When NAC 800 is deployed as a single-

server installation, NAC 800 becomes a Layer 2 bridge that requires

no changes to the network configuration settings. When NAC 800 is

installed in a multiple-server installation, you might have to configure

the switch that connects the NAC 800 enforcement servers to use

Spanning Tree Protocol (STP) if STP is not already configured.

NAC 800 allows devices to access the network or blocks devices from

accessing the network based on their Internet Protocol (IP) address

with a built-in firewall (iptables).

■DHCP – When deploying NAC 800 inline with a Dynamic Host Config-

uration Protocol (DHCP) server, all DHCP requests pass through the

NAC 800 server(s) Layer 2 bridge. For a quarantined device, NAC 800

distributes the quarantined IP address for the device. If NAC 800

allows the device to have access, NAC 800 allows your real DHCP

server to distribute a non-quarantined IP address. NAC 800 assigns a

DHCP IP address based on the quarantine area parameters you define

during configuration. You can place restrictions on network access

either at the gateway for the device using Access Control Lists (ACLs),

or on the device by removing the device's gateway and adding static

routes for accessible networks.

■802.1X– When deploying NAC 800 in an 802.1Xenvironment, you must

install it where it can communicate with the Remote Authentication

Dial-In User Service (RADIUS) server (or, NAC 800 has a built-in

Ethernet Information

Quick-start Card-3

RADIUS server that you can use). The RADIUS server communicates

with the switch, which performs the quarantining by moving ports or

MAC addresses in and out of virtual local area networks (VLANs).

Ethernet Information

The Ethernet interfaces should be attached as follows:

■Ethernet Port1 – Connect to the corporate LAN (the internal network

side)

■Ethernet Port2 – Connect to a switch, VPN, or DHCP server (the

Internet or endpoint side)

Port Information

You might need to configure some firewalls and routers to allow NAC 800 to

access the following ports for testing:

■Agentless test method – 137, 138, 139, and 445

■ActiveX and agent-based test method – 1500

■License validation and test updates – update.hp.com port 443

■Software and operating system updates – download.hp.com port 80

User Documents

The following user documents are available at www.procurve.com/nactools:

1. ProCurve Network Access Controller 800 Hardware Installation Guide

– Refer to this document first to see how to prepare for and perform the

physical installation of the appliance and how to establish initial

management access. This document contains appliance specifications,

safety information, and appliance certifications.

2. ProCurve Network Access Controller 800 Configuration Guide – Refer

to this document second, to understand the product's features,

capabilities, and use. This document explains how to configure the

appliance based on the usage model you choose to deploy in your

network.

Updates and Upgrades

Quick-start Card-4

3. ProCurve Network Access Controller 800Users’ Guide – Refer to this

document last for information on configuring, monitoring activities,

creating NAC policies, and running reports.

Updates and Upgrades

See the ProCurve Network Access Controller 800 Configuration Guide for

information on updates and upgrades.

Getting Support

ProCurve prides itself on providing exceptional customer support.

See Technical support – www.procurve.com

Hewlett-Packard Company

8000 Foothills Boulevard, m/s 5551

Roseville, California 95747-5551

http://www.hp.com/go/hpprocurve

© Copyright 2007Hewlett-Packard Development Company, L.P. All Rights Reserved.

Table des matières

Autres manuels HP Routeur réseau

HP

HP VSR1000 Manuel d'installation

HP

HP StorageWorks SR2122 Manuel utilisateur

HP

HP Pavilion a6600 Manuel utilisateur

HP

HP MSR954 Series Manuel utilisateur

HP

HP A-MSR20 Comment utiliser

HP

HP A-MSR30-16 Instructions d'installation

HP

HP ProCurve Networking J8453A Manuel utilisateur

HP

HP FlexNetwork MSR3064 Manuel utilisateur

HP

HP 7000dl Series Manuel utilisateur

HP

HP FlexNetwork 6600 Manuel utilisateur

HP

HP MSR1003-8S Manuel d'installation

HP

HP 5800 Instructions d'utilisation

HP

HP 7000dl Series Instructions d'utilisation

HP

HP StorageWorks MPX200 Mode d’emploi

HP

HP A5830 Series Manuel utilisateur

HP

HP MSR SERIES Manuel utilisateur

HP

HP Fax 650 Manuel utilisateur

HP

HP ProCurve Secure 7102dl Instructions de montage

HP

HP 3600 v2 Series Manuel utilisateur

HP

HP A58x0AF Bck(pwr)-Frt(ports) Instructions de montage

HP

HP MSR 93 Series Manuel utilisateur

HP

HP 1810 series Manuel utilisateur

HP

HP VSR1000 Manuel utilisateur

HP

HP 5120 SI Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité