HP MC68360 Manuel utilisateur

Graphical User Interface User’s Guide

MC68360/68EN360

Emulator/Analyzer

(HP 64780A)

Notice

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose. Hewlett-Packard shall not be liable for errors

contained herein or for incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information, which is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of

Hewlett-Packard Company. The information contained in this document is subject

to change without notice.

MS-DOS(R) is a U.S. registered trademark of Microsoft Corporation.

UNIX(R) is a registered trademark in the United States and other countries,

licensed exclusively through X/Open Company Limited.

Hewlett-Packard Company

P.O. Box 2197

1900 Garden of the Gods Road

Colorado Springs, CO 80901-2197, U.S.A.

RESTRICTED RIGHTS LEGEND. Use, duplication, or disclosure by the U.S.

Government is subject to restrictions set forth in subparagraph (C) (1) (ii) of the

Rights in Technical Data and Computer Software Clause at DFARS 252.227-7013.

Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A.

Rights for non-DOD U.S. Government Departments and Agencies are as set forth

in FAR 52.227-19(c)(1,2).

Printing History

New editions are complete revisions of the manual. Many product updates and

fixes do not require manual changes, and manual corrections may be done without

accompanying product changes. Therefore, do not expect a one-to-one

correspondence between product updates and manual revisions.

Edition 1 B3091-97000, December 1993

Edition 2 B3091-97001, April 1996

Safety and Certification and Warranty

Safety information, and certification and warranty information can be found at the

end of this manual on the pages before the back cover.

iii

The HP 64780A Emulator

Description

The HP 64780A emulator supports the Motorola 68360 and 68EN360

microprocessor operating at clock speeds up to 25 MHz.

The emulator supports both 5V and 3.3V operation. The emulator plugs directly

into a PGA socket, and it can be plugged into a PQFP target system using optional

accessories.

The emulator plugs into the modular HP 64700 instrumentation card cage and

offers 80 channels of processor bus analysis with the HP 64794A or HP 64704A

emulation-bus analyzer. Up to eight megabytes of emulation memory may be

installed on the probe. High performance download is achieved through the use of

an optional LAN or RS-422 interface. A pair of RS-232 ports and a

firmware-resident interface allow debugging of a target system at remote locations.

For software development, the HP AxCASE environment is available on SUN

SPARCsystems and on HP workstations. This environment includes an ANSI

standard C compiler, assembler/linker, a debugger, the HP Software Performance

Analyzer that allows you to optimize your product software, and the HP Branch

Validator for test suite verification. The C compiler, assembler/linker, and

debugger are also available for MS-DOS systems.

Language support is also available from several third-party vendors. This capability

is provided through the HP 64700’s ability to consume several industry standard

output file formats.

Ada language support is provided on HP 9000 workstations by third-party vendors

such as Alsys and Verdix. An Ada application developer can use the HP emulator

and any compiler that generates HP/MRI IEEE-695 to do exhaustive, real-time

debugging in-circuit or out-of-circuit.

Features

HP 64780A Emulator

•25 MHz active probe emulator

•5V and 3.3V operation

•No wait states to target memory up to 25 MHz

•Fast termination cycles to target memory up to 25 MHz

•Unlimited software breakpoints

•Symbolic support

•36 inch cable and 219 mm (8.8") x 102 mm (4") probe, terminating in PGA

package

•Background and foreground monitors

•Simulated I/O with workstation interfaces

•Consumes IEEE-695, HP-OMF, Motorola S-Records, and Extended Tek Hex

File formats directly. (Symbols are available with IEEE-695 and HP-OMF

formats.)

•Multiprocessor emulation

–synchronous start of 32 emulation sessions

–cross triggerable from another emulator, logic analyzer, or oscilloscope

•Demo board and self test module included

Emulation-bus analyzer

•80-channel emulation-bus analyzer

•Post-processed dequeued trace with symbols

•Eight events, each consisting of address, status, and data comparators

•Events may be sequenced eight levels deep and can be used for complex

trigger qualification and selective store

Emulation memory

•Up to 8 Mbytes of emulation memory

•All emulation memory is dual-ported

•Mapping resolution is 256 bytes

•No wait states required for emulation memory for processor speeds up to

25 MHz

•Fast termination cycles to emulation memory supported up to 10 MHz

In This Book

This manual shows you how to use the HP 64780A emulator through its Graphical

User Interface for the MC68360 microprocessor. It is divided into the following

parts:

Part 1 contains the Quick Start Guide. It shows you how to quickly become

productive with the emulation system.

Part 2 explains how to accomplish common tasks, often requiring use of several

emulator/analyzer commands together. This part assumes you know how to use the

commands to control the emulator. Instructions are given to help you connect the

emulation probe into a target system, get the desired interface on screen, and use

the emulator/analyzer commands to control the emulation processor while making

emulation measurements. This part also shows you how to use the emulation-bus

analyzer for debugging, use the Software Performance Measurement Tool supplied

with the emulator, and couple two or more emulators to coordinate measurements

involving more than one processor.

Part 3 shows you how to change the appearance or behavior of the Graphical User

Interface, and describes in detail each of the commands available in the

emulator/analyzer, and lists each of the messages you may see while using the

MC68360 emulator/analyzer, along with suggested corrective actions.

Part 4 of this book shows you how to install the Graphical User Interface and

Softkey Interface software, and how to update your emulator/analyzer firmware

with the progflash command, and display current firmware version information.

The Hewlett-Packard M68360 Emulator/Analyzer Installation/Service/Terminal

Interface User’s Guide shows you how to install the emulator hardware into the

card cage, install SRAM modules and covers on the emulation probe, and how to

connect the probe to the demo board and verify performance of the emulation

hardware. It also provides a thorough analysis of possible problems and their

solutions. It also lists the complete specifications and characteristics of the

M68360 emulator. It shows you how to connect the emulator into an MC68360

target system and overcome differences between the specifications and

characteristics of the target microprocessor and those of the emulator.

Contents

Part 1 Quick Start Guide

1 Getting Started

The Emulator/Analyzer Interface — At a Glance 4

The Softkey Interface 4

Softkey Interface Conventions 5

The Graphical User Interface 6

Graphical User Interface Conventions 8

The Getting Started Tutorial 11

Step 1. Start the demo 12

Step 2: Display the program in memory 13

Step 3: Run from the transfer address 14

Step 4: Step high-level source lines 15

Step 5: Display the previous mnemonic display 16

Step 6: Run until an address 17

Step 7: Display data values 18

Step 8: Display registers 19

Step 9: Step assembly level instructions 20

Step 10: Trace the program 21

Step 11: Display memory at an address in a register 23

Step 12: Exit the emulator/analyzer interface 24

Solving Problems 24

vii

Part 2 Using The Emulator

2 Plugging into a Target System

Connecting the Emulator to the Target System 29

Step 1. Turn OFF power 30

Step 2. Connect the probe to the target system 31

Step 3. Turn ON power 32

Plugging into the Motorola QUADS Target System 33

To connect the emulator to the Motorola QUADS 34

3 Starting and Exiting HP 64700 Interfaces

Starting the Emulator/Analyzer Interface 41

To start the emulator/analyzer interface 41

To start the interface using the default configuration 42

To run a command file on interface startup 43

To display the status of emulators 43

To unlock an interface that was left locked by another user 44

Opening Other HP 64700 Interface Windows 45

To open additional emulator/analyzer windows 45

To open the high level debugger interface window 46

To open the software performance analyzer (SPA) interface window 46

Exiting HP 64700 Interfaces 47

To close an interface window 47

To exit a debug/emulation session 48

4 Entering Commands

Using Menus, the Entry Buffer, and Action Keys 51

To choose a pulldown menu item using the mouse (method 1) 52

To choose a pulldown menu item using the mouse (method 2) 53

To choose a pulldown menu item using the keyboard 53

To choose pop-up menu items 55

To place values into the entry buffer using the keyboard 56

Contents

viii

To copy-and-paste to the entry buffer 56

To recall entry buffer values 59

To use the entry buffer 59

To copy-and-paste from the entry buffer to the command line entry area 60

To use the action keys 61

To use dialog boxes 61

To access help information 65

Using the Command Line with the Mouse 66

To turn the command line on or off 66

To enter a command 67

To edit the command line using the command line pushbuttons 68

To edit the command line using the command line pop-up menu 69

To recall commands 70

To get help about the command line 70

Using the Command Line with the Keyboard 71

To enter multiple commands on one command line 71

To recall commands 72

To edit commands 72

To access on-line help information 73

Using Command Files 74

To start logging commands to a command file 77

To stop logging commands to a command file 77

To playback (execute) a command file 78

Using Pod Commands 79

To display the pod commands screen 80

To use pod commands 80

Forwarding Commands to Other HP 64700 Interfaces 81

To forward commands to the high level debugger 81

To forward commands to the software performance analyzer 82

Contents

5 Configuring the Emulator

Using the Configuration Interface 85

To start the configuration interface 86

To modify a configuration section 88

To apply configuration changes to the emulator 90

If apply to emulator fails 91

To store configuration changes to a file 92

To change the configuration directory context 93

To display the configuration context 93

To access help topics 94

To access help for a configuration item in a dialog box 94

To exit the configuration interface 95

To load an existing configuration file 95

Verifying the Emulator Configuration 96

To display information about chip selects 96

To display information about bus interface ports 97

To display information about the memory map 97

To display information about the reset mode configuration 98

To review the upper address mode of the present configuration 98

To display information about the present clock input mode 99

To display assembly language instructions for setting up the SIM 99

To check for configuration inconsistencies 100

To verify the emulator configuration 101

6 Using the Emulator

Using the EMSIM Registers 105

To view the SIM register differences 107

To synchronize to the 68360 SIM registers 107

To synchronize to the EMSIM registers 108

To restore default values in the EMSIM registers 108

To assign an MBAR value for the M68360 register set 109

Loading and Storing Absolute Files 110

To load absolute files 110

To load absolute files without symbols 111

To store memory contents into absolute files 111

Contents

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Instrument de mesure

HP 1000 Series Manuel utilisateur

HP 85108A Guide de l'utilisateur

HP 1660CS-Series Manuel utilisateur

HP E1563A Manuel utilisateur

HP E4418A Manuel utilisateur

HP ESA-L1500A Manuel d'utilisation et d'entretien

HP HP 37722A Manuel utilisateur

HP 333A Manuel de service

HP 339A Manuel de service

HP 428B Manuel de service

HP E5970A Manuel utilisateur

HP HPE Apollo 2000 Gen10 Plus Manuel utilisateur

HP 1630A Manuel du propriétaire

HP 8568B Manuel d'installation et d'exploitation

HP 333A Manuel utilisateur

HP 8901B Manuel d'utilisation et d'entretien

HP 85106D Manuel utilisateur

HP 8590 E-Series Manuel d'utilisation et d'entretien

HP 8590 E-Series Manuel utilisateur

HP E3491A Instructions d'installation et d'entretien

HP 3400A Manuel de service

HP 400D Manuel du propriétaire

HP 4155A Manuel utilisateur

HP 8690B Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur