HP DMXTM 400/430 Manuel utilisateur

DMX400/430

Operator’s Manual

HP PCL-4, and HP Laser Jet II are Trademarks of Hewlett Packard Corporation.

CG Triumvirate is a trademark of Agfa Corporation.

CG Times, based upon Times New Roman under license from The Monotype

Corporation.

plc, is a product of Agfa Corporation.

DMX, SEAQ, and PC Batch are trademarks of Datamax Barcode Products

Corporation.

As an Energy Star Partner, Datamax Corporation has determined that this product

meets the Energy Star guidelines for energy efficiency.

Firmware (Software) Agreement:The enclosed Firmware (Software) resident

in the EPROM’s is owned by Licensor or its suppliers and is licensed for used

only on a single printer in the user’s Trade or Business. The User agrees not

to, and not to authorize or permit any other person or party to, duplicate

or copy the EPROM’s or the information contained in the EPROM’s.

The firmware (Software) is protected by applicable copyright laws and

Licensor retains all rights not expressly granted. In no event will Licensor or

its suppliers be liable for any damages or loss, including direct, incidental,

economic, special, or consequential damages, arising out of the use or

inability to use the Firmware (Software).

Information in this document is subject to change without notice and does not

represent a commitment on the part of Datamax Barcode Products

Corporation. No part of this manual may be reproduced or transmitted in any

form or by any means, for any purpose other than the purchaser's personal use,

without the expressed written permission of Datamax Corporation.

7500 Flying Cloud Drive • Suite 655 • Eden Prairie, Minnesota 55344

(612) 946-0026

Part Number: 88-2190-01

Revision: A2

Agency Compliance and Approvals:

UL: UL1950 Information Technology Equipment

CSA: C22.2 No. 950-M89

TUV: EN60950

VDE: Class B Vfg. 243/1991

1. Nur für Gebrauch innerhalb eines Gebäudes geeignet.

2. Bei Gefahr, Kabel aus der Steckdose herausziehen

3. Falls kein Kabel mitgeliefert wurde, bitte Folgendes bei der

Anschaffung eines Kabels beachten:

Für 230 Volt (Europa):Benützen Sie ein Kabel, das mit "HAR"

markiert ist, bestehend mindestens aus einem H05VV-F Kabel, das

mindestens 0,75 Quadratmillimeter Drahtdurchmesser hat; sowie eine

IEC320 Steckdose und einen für das Land geeigneten Stecker, 6A, 250

Volt.

1. This unit is intended for indoor use only.

2. Disconnect power supply cord in case of emergency.

3. When power supply cord is not provided; for proper power

supply cord selection please see below:

For 230 Volt Operation (Europe):Use a cord set, marked "HAR,"

consisting of a min H05VV-F cord which has a minimum 0.75

square mm diameter conductors, provided with an IEC 320

receptacle and a male plug for the country of installation rated 6A,

250V

FCC: This device complies with Part 15 of FCC rules.

Note: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy, and if

not installed and used in accordance with the instructions in this

manual, may cause interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Important Safety Instructions

Your Barcode Printer has been designed to give you many years of

safe, reliable service. As with all electrical equipment, there are a

few basic precautions you should take to avoid getting hurt or

damaging the Printer.

•Carefully read the installation and operating instructions

provided with your Printer.

•Read and follow all warning instruction labels on the Printer

itself.

•Place the Printer on a flat, firm, solid surface.

•To protect your Printer from overheating, make sure all

openings on the Printer are not blocked.

•Do not place the Printer on or near a heat source, (i.e., a radiator

or heat register).

•Do not use your Printer near water, or spill liquid of any kind

into it.

•Be certain that your power source matches the rating listed on

the back of the Printer. If you are unsure, check with your

dealer or with your local power company.

•Do not place the power cord where it will be walked on. If the

power cord becomes damaged or frayed replace it immediately.

•Do not insert anything into the ventilation slots or openings on

the Printer.

•Only qualified, trained service technicians should attempt to

repair your Printer.

♦Contents

♦Getting Started

1.0 Introduction.........................................................1

1.1 Unpacking and Inspection....................................1

1.2 Supplies Necessary to Print..................................2

1.3 Location of Parts on your Printer .........................2

1.4 Tear-off Assembly Installation.............................4

1.5 Using the Printer’s Control Panel..........................5

1.6 Using Print Media.................................................8

1.6.1 Label Loading Instructions ......................9

1.6.2 Adjusting Printhead Pressure ................10

1.7 Ribbon Loading.................................................12

1.7.1 Ribbon Loading Instructions ................12

1.8 Using the Printer’s Options.................................13

1.8.1 Available Modules ................................13

1.8.2 Cutter ....................................................14

1.8.3 Peel and Present Mechanism .................14

♦Printing Labels

2.0 Checking Voltage Selection................................15

2.1 Power-up Self-Test............................................15

2.2 Interfacing to the Printer.....................................18

2.3 Sample Installation.............................................19

2.4 Switch Settings...................................................21

2.4.1 Setting the Baud Rate ............................22

2.4.1 Other Switches ......................................23

♦Creating Labels Using Internal Batch Software

3.0 Introduction.......................................................25

3.1 The Printer used with a LINK CRT....................26

3.2 Formatting and Printing Labels...........................29

3.3 Create/Modify Label Screen ..............................34

3.4 Print Label Screen ............................................47

3.4.1 Printing a Label from Print Label Screen 47

3.5 System Maintenance Screen ..............................49

(Continued)

3.6 Quick Reference Listing .....................................51

3.6.1 Create/Modify Label Commands ..........51

3.6.2 Print Parameters (ALT-P)......................52

3.6.3 Special Keys .........................................52

♦Printing Labels

4.0 Introduction........................................................53

4.1 Programming Commands....................................53

4.2 Programming Examples.......................................59

♦Troubleshooting

5.0 Introduction........................................................61

5.1 Controlling Print Quality.....................................62

5.2 Aligning the Printhead.........................................63

5.2.1 Direct-Thermal Stock ..........................63

5.2.2 Tag Stock or Stiff Media......................63

5.2.3 Mechanical Adjustments.......................64

5.3 Printhead Alignment Procedure...........................65

5.3.1 Label Stock Tracking Adjustment.........65

5.3.2 Ribbon Feed and Tracking Adjustments65

5.3.3 Fine Printhead Adjustment....................67

5.4 Adjusting Printhead Pressure and Support..........67

5.5 Troubleshooting..................................................68

♦Maintenance

6.0 Cleaning the Printer.............................................73

6.1 Cleaning the Printhead ........................................74

(Continued)

iii

♦Appendix A

ASCII Control Code Chart........................................A-1

♦Appendix B

Switch Settings and Cable Interfacing.......................B-1

♦Appendix C

Available Fonts and Barcodes...................................C-1

♦Appendix D

Error Codes ..............................................................D-1

♦Appendix E

Cable Listings ...........................................................E-1

♦Appendix F

Specifications............................................................F-1

♦Appendix G

Warranty Information...............................................G-1

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Étiqueteuse

HP Indigo press ws4500 Manuel utilisateur

Manuels Étiqueteuse populaires d'autres marques

Brother

Brother P-Touch 2420PC Manuel utilisateur

newell

newell Dymo LabelManager 210D Manuel utilisateur

Brother

Brother TD-4000 Manuel utilisateur

U-Line

U-Line BROTHER H-8754 Manuel utilisateur

Tharo Systems

Tharo Systems H-435+ Manuel utilisateur

Brother

Brother E300 Manuel utilisateur

Godex

Godex RT700 SERIES Manuel utilisateur

ID Technology

ID Technology 252 Manuel utilisateur

Labelmate

Labelmate MC-11 Manuel utilisateur

CAB

CAB XD4M/300 Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Brother

Brother P-touch PT-9700PC Manuel utilisateur

TSC

TSC PEX1000 Series Manuel utilisateur

Adkins

Adkins Label Master Manuel utilisateur

Epson

Epson LabelWorks LW-400 Manuel utilisateur

Primera

Primera 510212 Manuel utilisateur

Brady

Brady BradyPrinter S3100 Manuel utilisateur

DuraLabel

DuraLabel LabPRO Manuel utilisateur