HP Visualize b1000 Manuel

HP VISUALIZE B Class and C Class UNIX®

Workstations

Parts Replacement Guide

Manufacturing Part Number: A4985-90036

Edition E0100

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not

furnished by Hewlett-Packard.

this document may be photocopied, reproduced or translated to another language without the prior written

consent of Hewlett-Packard Company.

Hewlett-Packard Warranty Statement

Refer to Warranty & Support for your HP Workstation for warranty terms applicable to your Hewlett-Packard

product and replacement parts.

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government Department of Defense is subject to restrictions as set

forth in paragraph (b)(3)(ii) of the Rights in Technical Data and Software clause in DFARS 252.227.7013.

UNIX is a registered trademark in the United States of America and other countries, licensed exclusively

through X/Open Company Limited.

This software and documentation is based in part on the Fourth Berkeley Software Distribution under license

from the Regents of University of California.

Contents

1. Getting Started

Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Electrostatic Discharge (ESD) Precautions . . . . . . . . . . . . . . . . . . . . . .5

Replacement Part Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Safely Powering Down the B Class and C Class Workstation . . . . . . . . .7

Product Exploded Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2. Parts Removal and Replacement

Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Removing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .10

Replacing the Terminators and Cables. . . . . . . . . . . . . . . . . . . . . . . . .11

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Removing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Replacing the Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Removing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Replacing the Left Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Removing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Memory Card(s) DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Removing and Replacing DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Removing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Replacing PCI I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CD ROM Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Contents

Removing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replacing the CD ROM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Removing the Front-Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Replacing the Front-Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Removing the Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Hard Disk Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Removing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Putting a Disk Drive into its Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Replacing the Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

I/O Fan and Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Removing the I/O Fan and Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Removing and Replacing the Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Removing and Replacing the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . 37

Replacing the Fan and Speaker Bracket . . . . . . . . . . . . . . . . . . . . . . . 37

Removing and Replacing the System Board. . . . . . . . . . . . . . . . . . . . . . 38

Disconnecting the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Removing the old System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Replacing the System Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Real Time Clock (RTC) Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Removing the Real Time Clock (RTC) Module . . . . . . . . . . . . . . . . . . 42

Replacing the Real Time (RTC) Module . . . . . . . . . . . . . . . . . . . . . . . 43

Removing and Replacing the System Board Cooling Fans . . . . . . . . . . 44

Replacing the System Board Cooling Fans . . . . . . . . . . . . . . . . . . . . . 45

3. Wrapping Up

Verifying System Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Returning the Defective Exchange Assembly . . . . . . . . . . . . . . . . . . . 47

1Getting Started

The following important information must be adhered to for proper removal and

replacement of all Hewlett-Packard parts.

Safety Warnings

WARNING Removing the device cover may expose sharp edges in the equipment

chassis. To avoid injury, use care when installing customer add-on

devices.

NOTE Before performing removal/replacement procedures, position the workstation

on a cushioned ﬂat, stable surface, such as a table top or workbench.

NOTE Installing the recommended HP replacement part in your B Class and C

Class workstation does not affect the regulatory and safety classiﬁcations or

approvals listed in the original owner’s guide.

Electrostatic Discharge (ESD) Precautions

To prevent damage to the B Class and C Class workstation, observe all of the following

ESD precautions while performing removal and replacement procedures:

• Remove all ESD-generating materials from the work area in which you will remove and

replace the workstation ﬁeld replaceable unit(s).

• Open the ESD materials provided with the replacement part kit. Unfold the black

conductive sheeting (antistatic mat) and place it under a corner of the workstation.

• Wear a static strap to ensure that any accumulated electrostatic charge is discharged

from your body to ground. Attach the static-grounding wrist strap by following the

instructions on the package. Attach the sticky end of the wrist strap to bare metal on

the rear panel of the workstation.

• Connect all equipment together, including the static-free mat, static strap, clips

attached to the wrist strap, nodes, and peripheral units.

• Keep uninstalled printed circuit boards in their protective antistatic bags.

• Once you have removed printed circuit boards from their protective antistatic bags,

handle the printed circuit boards by their edges only.

6Chapter1

Getting Started

Replacement Part Kit Contents

Take a moment to verify that your kit contains the following contents:

• The replacement part.

• Part Number: A3024-80004, Electrostatic Discharge (ESD) materials

• Removal/Replacement Instructions

If you are missing any part or any documentation, please call your designated service

representative.

Required Tools

You will need the following tools for removal/replacement procedures:

• T-10 and/or T-15 Torx drivers

• Light-duty ﬂat-blade screwdriver with a 150mm (6-inch) blade

• Needle-nosed pliers

• ESD materials

Chapter 1 7

Getting Started

Safely Powering Down the B Class and C Class Workstation

You must complete the following steps before performing any of the removal and

replacement procedures:

NOTE Remove any accessory bag(s) and their black tab screws, if present, from the

rear of the workstation.

1. Shut down the workstation by executing “shutdown -h” as user root. This ensures

that all programs are terminated and all data is saved before switching the power off.

Power down the workstation by simply pressing the power switch on the front panel.

Power off the monitor and any attached peripheral devices.

2. After 30 seconds, unplug the workstation’s power cord and all peripheral devices from

AC power outlets. Before attempting to move the workstation to a disassembly area,

disconnect all peripherals from the back of the system.

3. Place the workstation on a ﬂat, stable surface, such as a tabletop or ﬂoor. To protect

against scratches, remove miscellaneous debris from the work surface.

8Chapter1

Getting Started

Product Exploded Diagram

Refer to the ﬁgure below for a basic parts overview of the B Class and C Class workstation.

Figure 1-1. Exploded View

Chassis

Front-Panel Display

Hard Disk Tray

CD Drive Tray

Floppy Drive Tray

System Board

DIMMs (Memory)

Memory Fan

Side Panel

Power

System-Board Fans

I/O Fan/Speaker Bracket

Air Divider

I/O Card

Speaker

I/O Fan

Supply

Retainer Clip

2Parts Removal and Replacement

This chapter describes how to remove and replace the various parts in the B Class and C

Class workstations.

10 Chapter2

Parts Removal and Replacement

Terminators and Cables

This section describes how to remove and replace the Terminators and Cables

Removing the Terminators and Cables

1. After powering down the workstation as described in the “Getting Started” chapter,

unplug the power cable from the back of the workstation. To avoid ESD damage to

components, carefully follow the ESD procedures (also described in the “Getting

Started” chapter).

2. Remove the two SCSI terminators from the back of the machine, as shown below. Or, if

you have already replaced either or both of the terminators with cables to external

peripheral devices, remove those cables., LAN cable, USB cables, and any other cables

from the back of the workstation.

Figure 2-1. Removing all Terminators and Cables

1. Remove the cables from the USB Clip from the back of the Workstation.

SCSI Terminators

Audio In/Out Ports

Parallel Port

LAN Port

USB Ports

Serial Ports

Power Plug

Autres manuels pour Visualize b1000

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Ordinateur de bureau

HP Pavilion t500 - Desktop PC Manuel utilisateur

HP Pavilion A6140 Manuel utilisateur

HP Pavilion Elite E-300 - Desktop PC Manuel utilisateur

HP dx2420 - Microtower PC Manuel utilisateur

HP Compaq 100B Instructions d'utilisation

HP Pavilion t388d Manuel utilisateur

HP dx2250 - Microtower PC Manuel utilisateur

HP Visualize c160 Manuel utilisateur

HP s7600n - Pavilion Media Center Fiche technique

HP Z200 - Small Form Factor Workstation Manuel utilisateur

HP Pavilion Gaming 690-0000 PC Series Manuel utilisateur

HP Pavilion p7-1200 Manuel d'utilisation et d'entretien

HP Pavilion t400 - Desktop PC Instructions d'installation

HP TouchSmart 610-1200 Manuel utilisateur

HP Compaq Presario Manuel

HP Vectra VL800 Manuel utilisateur

HP LaserJet 9000 Manuel utilisateur

HP Pavilion Slimline s7200 - Desktop PC Manuel utilisateur

HP Desktop Pro A G2 Manuel

HP Compaq Presario Manuel

HP Compaq dc5750 Series Instructions d'utilisation

HP CQ5110F - Presario - 3 GB RAM Manuel d'utilisation et d'entretien

HP Pavilion a200 - Desktop PC Manuel utilisateur

HP Compaq dc5000 SFF Manuel d'utilisation et d'entretien

Manuels Ordinateur de bureau populaires d'autres marques

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur

Everex

Everex eXplora Manuel utilisateur

Lenovo

Lenovo ThinkCentre M75e Manuel utilisateur

Dell

Dell Alienware Area-51 R4 Manuel utilisateur