HP Intel EtherExpress PRO 10+ ISA Manuel utilisateur
Intel EtherExpress PRO 10+ ISA
Ethernet Adapter
Installation Guide
Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental
or consequential damages in connection with the furnishing, performance, or use
of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated to another language without the prior written consent
of Hewlett-Packard Company.
Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft
Corporation.
MMXTM is a trademark of Intel Corporation.
Pentium® is a registered trademark of Intel Corporation.
Hewlett-Packard France
Commercial Desktop Computing Division
38053 Grenoble Cedex 9
France
©1999 Hewlett Packard Company
1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Microsoft Windows 95 SR2.5
1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet
Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 3.51 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 3.51 system that supports NetBEUI, TCP/
IP, NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA
adapter card into an ISA slot.
2Connect network cable media to the PRO 10+ card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “SOFTSET2.EXE”.
5Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 05 03 07
I/O Address 210 210 210
1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Connecting to a Windows NT 3.51 Server
9Click on “Next” to continue installation then insert the Intel EtherExpress
drivers disk.
10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.
11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress
drivers disk inserted, set the path to “A:\” and click “OK”.
12 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
13 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
14 Click on “Close” button, and files will copy.
15 When prompted for the file”NETAPI.DLL”, set the path to your Windows
95 files and click “OK”.
16 Click on the “Yes” button to finish the installation and restart your
computer.
2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Microsoft Windows 95 SR2.5
2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet
Adapter
Microsoft Windows 95
SR2.5
Connecting to a
Windows NT 4.0 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Microsoft Windows NT Server 4.0 system that supports NetBEUI, TCP/IP,
NWLink IPX/SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA
adapter card into an ISA slot.
2Connect network cable media to the PRO 10+ card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “SOFTSET2.EXE”.
5Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 05 03 07
I/O Address 210 210 210
2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Connecting to a Windows NT 4.0 Server
9Click on “Next” to continue installation then insert the Intel EtherExpress
drivers disk.
10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.
11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress
drivers disk inserted, set the path to “A:\” and click “OK”.
12 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
13 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
14 Click on “Close” button, and files will copy.
15 When prompted for the file”NETAPI.DLL”, set the path to your Windows
95 files and click “OK”.
16 Click on the “Yes” button to finish the installation and restart your
computer.
3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Microsoft Windows 95 SR2.5
3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet
Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
Netware 3.12 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 3.12 Server that supports NetBEUI, TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA
adapter card into an ISA slot.
2Connect network cable media to the PRO 10+ card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “SOFTSET2.EXE”.
5Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 05 03 07
I/O Address 210 210 210
3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Connecting to a Novell Netware 3.12 Server
9Click on “Next” to continue installation then insert the Intel EtherExpress
drivers disk.
10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.
11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress
drivers disk inserted, set the path to “A:\” and click “OK”.
12 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
13 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
14 Click on “Close” button, and files will copy.
15 When prompted for the file”NETAPI.DLL”, set the path to your Windows
95 files and click “OK”.
16 Click on the “Yes” button to finish the installation and restart your
computer.
4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Microsoft Windows 95 SR2.5
4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet
Adapter
Microsoft Windows 95
SR2.5
Connecting to a Novell
Netware 4.11 Server
Requirements
• HP Vectra with Windows 95 SR2.5.
• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk.
• Microsoft Windows 95 SR2.5 media.
• Novell NetWare 4.11 Server that supports NetBEUI, TCP/IP, NWLink IPX/
SPX, and NWLink NetBIOS transfer protocols.
Device Configuration
Procedure
1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA
adapter card into an ISA slot.
2Connect network cable media to the PRO 10+ card.
3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.
4Insert the Intel drivers disk, “EtherExpress Ethernet Drivers” and
execute “SOFTSET2.EXE”.
5Select “CONFIGURE NIC” and verify the resource settings listed above
under the heading “Device Configuration”.
6If changes are required, save those changes and exit.
7Remove the Intel Software driver diskette and restart the system.
8When Windows 95 restarts, a message will appear to indicate that a new
hardware has been found.
Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8
Interrupt 5 03 07
I/O Address 210 210 210
4 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter
Connecting to a Novell Netware 4.11 Server
9Click on “Next” to continue installation then insert the Intel EtherExpress
drivers disk.
10 Click on “Other Locations…”, set the path to “A:\” and click on “Finish”.
11 When prompted for the file”EPRONDI.DLL” with the Intel EtherExpress
drivers disk inserted, set the path to “A:\” and click “OK”.
12 Click “OK” to the “Network dialog box to provide computer / workgroup
names.
13 Specify your Computer Name, Workgroup, and Computer Description. (If
you do not have the required information, contact your network
administrator).
14 Click on “Close” button, and files will copy.
15 When prompted for the file”NETAPI.DLL”, set the path to your Windows
95 files and click “OK”.
16 Click on the “Yes” button to finish the installation and restart your
computer.
Ce manuel convient aux modèles suivants
3
Autres manuels HP Ordinateur de bureau
HP
HP Pavilion t600 - Desktop PC Manuel utilisateur
HP
HP Workstation Z210 CMT Manuel utilisateur
HP
HP Vectra VEi 7 Manuel
HP
HP Z VR Backpack G1 Manuel
HP
HP Z800 - Workstation - 6 GB RAM Manuel
HP
HP Pavilion w5100 Mode d'emploi
HP
HP dx5150 Manuel utilisateur
HP
HP Z600 - Workstation - 6 GB RAM Guide de référence
HP
HP Pavilion t400 - Desktop PC Manuel d'instructions
HP
HP EliteDesk 705 G5 Manuel
HP
HP Pavilion m9515 Manuel utilisateur
HP
HP Compaq dx2390 Manuel utilisateur
HP
HP 200 G3 Manuel
HP
HP Brio BA410 Manuel utilisateur
HP
HP DL320 - ProLiant - G3 Manuel utilisateur
HP
HP Firebird VoodooDNA 803 Manuel utilisateur
HP
HP 450 NG Manuel utilisateur
HP
HP Presario SR1200 - Desktop PC Manuel utilisateur
HP
HP Pavilion p6720f Manuel utilisateur
HP
HP Compaq Presario Fiche technique
