HP D7171A - NetServer - LPr Manuel utilisateur
1
IBM OS/2 Warp Server for e-Business
Installation Guide for Hewlett-Packard
NetServers
NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version L.17.01. If you
don't have the L.17.01 version CD-ROM and you're obtaining this document from the HP NetServer web site as a reference to
install an operating system, be sure to also check the HP NetServer web site for the latest available drivers.
©Copyright Hewlett-Packard Company
September 7, 1999
(This document is only available in English.)
Introduction
The objective of this document is to help Hewlett-Packard customers install IBM OS/2 Warp
Server for e-business on a HP NetServer system. For additional information on Hewlett-Packard
NetServers refer to the HP Information Assistant on the HP NetServer Navigator CD-ROM.
It is critical to know which disk adapters or disk array adapter are in the system before you start
the installation. The tables in the Appendix will help you identify what adapter is implemented or
embedded on the system board for each HP NetServer.
NOTE: The IBM OS/2 Warp Server for e-business is not supported on the HP NetServer
E series (E 30, E 40, E 45, E 50, and E 60).
Table of Contents
Installation Procedure: OS/2 Warp Server for e-business
Requirements
Creating the HP Drivers/Utilities Diskette
Installation Steps
APPENDIX
Installation Procedure: OS/2 Warp Server for e-business
Requirements
•Driver's Diskette for OS/2 Warp Server for e-business created from the HP NetServer
Navigator CD diskette library.
•OS/2 Warp Server for e-business CD
2
•Installation diskettes (to create installation diskettes from OS/2 CD insert you OS/2 CD in the
CD-ROM drive and type CDINST).
NOTE: I2O Mode is not supported by IBM OS/2 operating system, If there is a NetRAID
adapter in the system set the NetRAID mode to Mass-Storage using Set Class utility or
NetRAID's utility (Ctrl+M) before installing OS/2.
Creating the HP Drivers/Utilities Diskette
The "Drivers/Utilities" diskette is referred to in the HP NetServer Navigator CD-ROM and other
HP documentation as the "Drivers Diskette." The purpose of this diskette is to accomplish the
following three tasks:
Task 1) To backup one (or more) of your OS/2 installation diskettes. For OS/2 Warp and later
products, only Diskette 1 is backed up. We will refer to this backup copy of OS/2 Diskette 1 as
the "Work Diskette 1". When you install OS/2, you will use the backup copies in place of the
original diskettes that came in the OS/2 box.
Task 2) Identify the unused drivers on "Work Diskette 1" to make room for new drivers. Delete
the unwanted drivers from the "Work Diskette 1".
Task 3) Identify the required drivers for the system. Based on the boot setup. The following
drivers may be needed. Example:
AIC7870.ADD
SYM_HI.ADD
MRAID.ADD
Make a list of drivers that are needed and order them based on boot priority.
Task 4) Create the HP Drivers/Utility Diskette by stepping through one of the following
procedures. There are two ways to create the drivers diskette.
•Procedure One: Uses the OS/NOS icon section of the Navigator CD-ROM.
•Procedure Two: Uses the "Library diskette" section of the Navigator CD-ROM.
Procedure One
1. Boot the system from the HP Navigator CD-ROM.
2. From the Main Menu, select "Configuration Assistant and Installation Assistant".
3. Select Custom.
4. Select OS/2.
5. From the menu, select the version of OS/2 that you want to Install.
3
6. Read the information provided on the "Configuration Advisor" panel. Save the
information to a floppy diskette if you desire.
7. Select Continue.
8. From the "Custom Configuration" menu select "Create Drivers Diskette".
9. Label a blank diskette "HP NetServer IBM OS/2 Warp Drivers/Utilities Diskette".
Insert this diskette in drive A and select "Execute".
10. Remove the HP Navigator CD-ROM. Keep the newly created "Drivers/Utilities"
diskette in the floppy drive
11. Click on Exit. Select Yes to reboot system. Continue to Task 5.
Procedure Two
This is an alternate procedure for creating the "Drivers/Utilities" diskette using a section
called "Diskette Library" on the Navigator CDROM.
Keep in mind that if you need high resolution video, you will need to create additional video
drivers diskettes.
Use this procedure to create a "Drivers/Utilities" diskette using the "Diskette Library" on the
Navigator CDROM:
1. Boot the system from the HP Navigator CD-ROM
2. Select “NetServer Utilities”
3. Select “Diskette Library”
4. Select "NOS Drivers - OS/2 Warp Family" and then select “execute”.
5. Label a blank diskette “HP NetServer IBM OS/2 Warp Drivers/Utilities Diskette”, insert
the diskette when prompted and follow the instructions.
6. If needed, create the video driver diskettes by following the same procedure.
7. Click “Exit” when done.
8. Click “Yes”, to reboot the system. Continue to Task 5.
Task 5) Copy the required drivers (which are identified in Task 3) from the "HP
Drivers/Utilities” diskette to the "Work Diskette 1".
NOTE: Do not copy the NIC driver onto the diskette #1. The NIC driver can be loaded
during Network setup at the end of the installation.
Task 6) Edit the Config.sys file in "Work Diskette 1" to include the drivers entry which are
4
added in Task 5 and delete drivers entry which are removed in Task 2.
Task 7) Include "set copyfromfloppy=1" as the first line in config.sys in "Work Diskette 1" to
allow the installation process to copy drivers from floppy than from OS/2 Installation CDROM.
Installation Steps
1. Insert the Installation diskette and reboot your system.
2. Remove the Installation diskette and insert the Diskette #1 press Enter.
3. Replace the Diskette #1 with Diskette #2 and press Enter.
4. Insert the OS/2 Warp Server for e-business CD into the CD-ROM drive and press Enter.
5. At the Welcome Screen press Enter.
6. At the OS/2 Warp Server for e-business Installation screen press Enter to begin the
installation.
7. At the Volumes too small screen press Enter to modify the volumes sizes.
8. At the Modifying Volumes Warning screen press Enter.
9. At the Logical Volume Management Tool screen press Enter to continue.
NOTE: Logical Volume Management Tool will come up with logical view, to see the
physical view press F5.
10. Press Enter to install the Boot Manager.
NOTE: At this point only CD-ROM drive will be highlighted.
11. Select Install Boot Manager.
12. Press Enter again and select create a new volume.
13. Select create a volume that can be made Bootable and press Enter .
14. Select the drive letter C: for your boot drive and press Enter.
15. Type OS/2 for the volume name and press Enter.
16. Select a disk to be used to create the volume and press Enter.
17. Allocate from free space is highlighted, press Enter.
18. Free space is highlighted, press Enter.
19. Select a name for the partition C: and press Enter.
5
20. Select a size in megabytes for the partition and press Enter.
NOTE: If boot drive will be formatted as FAT, it should be less than 2GB.
21. Highlight the volume you just created and press Enter.
22. Select Set the Volume Installable and press Enter.
23. Press F3 to Exit LVM.
24. Save the changes and exit.
NOTE: Additional drives in the system should be partitioned and formatted after OS/2
installation is completed. Volume type selection is optional based on customer's need
(Compatibility Volume or LVM Volume).
25. Replace the diskette #2 with the Installation diskette and press Ctrl-Alt-Del.
26. Insert diskette #1 and press Enter.
27. Insert diskette #2 and press Enter.
28. At the Welcome screen press Enter.
29. At the OS/2 Warp Server for e-business installation screen press Enter.
30. At Installation Volume Selection, highlight Accept the volume and press Enter.
31. At Formatting the Installation Volume, highlight Perform a quick format and press
Enter.
32. At the select the File System screen , select High Performance and press Enter.
33. Remove the diskette and press Enter to restart the workstation and continue the installation.
34. At System Configuration click on Next to accept the default.
35. Click on Next again.
36. At Country Information select United States and press OK.
37. At Select System Default Printer, select Do Not Install default Printer.
NOTE: If you are installing a printer select the proper driver for it.
38. At Primary Display Driver Install, select VGA.
39. At the OS/2 Warp Server for e-business Setup and Installation, accept the default and
press Next.
40. After base operating system installation and configuration are complete press Next to begin
6
the Server Component installation.
41. At Information Screen, Do Not enter anything and click on Next.
42. At the Services screen, accept the default and click on Next.
43. At the Configuration screen, click on UserID and Password:
Enter USERID for UserID
Enter PASSWORD for Password
44. Click on File and Print Sharing Services and specify the Server name and Domain name.
45. Click on Network Adapters and Protocol Services, and load the NIC driver from the
Drivers Diskette you created from the HP NetServer Navigator CD and add the desired
Protocol.
46. Click on Install then click on OK.
47. Remove the NIC driver diskette, installation will continue until it is completed.
APPENDIX
This section provides additional information about HP NetServers and Disk Array Adapters used
with HP NetServers.
Table #1
NetServer #Ports SCSI Chip Driver Name
========= ====== ========= ===========
LX 2 AIC7880 AIC7870.ADD
LS 2 AIC7870 AIC7870.ADD
LH Pro 2 AIC7880 AIC7870.ADD
LH II 2 AIC7880 AIC7870.ADD
LH 3 2 SYM53c895 SYM8XX.ADD
LH 4 2 SYM53c895 SYM8XX.ADD
LH 3000 2 SYM53c896 SYM_HI.ADD
" 1 AIC7880 (SE)* AIC7870.ADD
LD Pro 1 AIC7880 AIC7870.ADD
LC 1 AIC7700 AIC7770.ADD
7
LC II 1 AIC7880 AIC7870.ADD
LC 3 1 AIC7880 AIC7870.ADD
LC 2000 2 SYM53c896 SYM_HI.ADD
E 40 1 AIC7860 AIC7870.ADD
E 45 1 AIC7860 AIC7870.ADD
E 50 1 AIC7880 AIC7870.ADD
E 60 2 AIC7895 AIC7870.ADD
LPr 1 SYM895 SYM8XX.ADD
* (SE stands for Single Ended)
Table #2
List of Hewlett-Packard Disk Array adapters and Drivers.
NetServer Adapter Name Driver Name
========= ============= ===========
E 30 NetRaid mraid.add
E 40 NetRaid mraid.add
E 45 NetRaid mraid.add
E 50 NetRaid mraid.add
E 60 NetRaid mraid.add
LC Mylex EISA 3609A hpda.add
LC Mylex PCI C3610A hpda.add
LC II NetRaid mraid.add
LC 3 NetRaid mraid.add
LC 2000 NetRaid mraid.add
LD Mylex PCI C3610A hpda.add
LD Pro Mylex PCI C3610A hpda.add
LF Mylex EISA 3609A hpda.add
LH Mylex PCI C3610A hpda.add
LH Pro Mylex PCI C3610A hpda.add
LH Pro NetRaid mraid.add
8
LH II NetRaid mraid.add
LH 3 NetRaid (*) mraid.add
LH 4 NetRaid (*) mraid.add
LH 3000 NetRaid (*) mraid.add
LM (All) Mylex EISA 3609A hpda.add
LS (All) Mylex PCI C3610A hpda.add
LX NetRaid mraid.add
LXr Pro8 NetRaid mraid.add
LPr NetRaid mraid.add
LXr 8000 NetRaid mraid.add
LXr 8500 NetRaid mraid.add
(*) Integrated controller.
Table #3
List of embedded Video chip for each NetServer.
NetServer Adapter Name
========= ============
E 30 S3 Trio 64
E 40 Cirrus CL5446 1M
E 45 Cirrus CL5446 1M
E 50 Cirrus CL5446 1M
E 60 ATI Rage IIC 2M
LC Trident 9000I 512K
LC II Cirrus CL5446 1M
LC 3 Cirrus CL5446 1M
LC 2000 ATI Rage IIC 2M
LD Trident 9000i 512K
LD Pro Trident 9000i 512K
LF Trident 9000i 512K
LH Trident 9000i 512K
9
LH Pro Trident 9000i 512K
LH II Trident 9000i 512K
LH 3 Cirrus CL5446 1M
LH 4 Cirrus CL5446 1M
LH 3000 ATI Rage IIC 2M
LM (All) Western Digital 512K
LS (All) Cirrus 5436 512K
LX Cirrus 5436 512K
LXr Pro8 S3 Virge
LPr Cirrus CL5446 1M
LXr8000 CL5446 1M
LXr8500 CL5446 1M
Note: Video adapters with 1M can be upgraded to 2M.
Table #4
This table provides a list of CD-ROM type for each NetServer
CD-ROM
NetServer Type
========= ======
E 30 IDE
E 40 IDE
E 45 IDE
E 50 IDE
E 60 IDE
LC SCSI
LC Plus SCSI
LC II IIDE
LC 3 IDE
LC 2000 IDE
LD SCSI
10
LD Pro SCSI
LF SCSI
LH SCSI
LH Pro SCSI
LH II SCSI
LH 3 IDE
LH 4 IDE
LH 3000 IDE
LM (All) SCSI
LS (All) SCSI
LX SCSI
LXr Pro8 IDE
LPr IDE
LXr 8000 IDE
LXr 8500 IDE
Autres manuels pour D7171A - NetServer - LPr
117
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels HP Ordinateur de bureau
HP
HP Vectra VL6 6 Manuel du produit
HP
HP Pro 3405 Series Instructions d'installation
HP
HP EliteDesk 800 G1 series Manuel utilisateur
HP
HP Compaq d220 MT Manuel
HP
HP Pavilion E h9-1200 Manuel utilisateur
HP
HP Presario SR1400 - Desktop PC Manuel utilisateur
HP
HP Vectra VE4 Manuel utilisateur
HP
HP Brio BAx Manuel utilisateur
HP
HP i2000 Manuel
HP
HP d330 - Desktop PC Manuel de l'opérateur
HP
HP B132L+ Manuel utilisateur
HP
HP Presario SR1200 - Desktop PC Manuel utilisateur
HP
HP j6700 Manuel utilisateur
HP
HP vectra vl420 Manuel du produit
HP
HP Pavilion 525 Instructions d'installation
HP
HP Bc1500 - BladeSystem - Blade PC Instructions d'utilisation et de sécurité
HP
HP Presario All-in-One CQ1-1200 - Desktop PC Fiche technique
HP
HP Kayak XA 05xx Manuel utilisateur
HP
HP Model 748 - VME Workstation Guide de référence
HP
HP Compaq GX5000T CTO Manuel utilisateur
