Hover-1 RAPTOR Manuel utilisateur
H OV E R B OA R D AT TAC H M EN T
RAPTOR
OPERATION MANUAL
H1-RPT-BGY
1
HELMETS SAVE LIVES!
Always wear a properly fitted helmet that complies with CPSC or CE safety standards when you
ride your hoverboard.
Correct Fit:
Make sure your helmet
covers your forehead.
Incorrect Fit:
Forehead is exposed and
vulnerable to serious injury.
Please visit
www.hover-1.com/troubleshoot
to request replacements for
missing or defective parts
2
This manual is designed to give you the information you need for the safe operation and maintenance of
your new Raptor. Please read it thoroughly before riding your Raptor.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your Raptor. Even if you are an experienced rider, it is
important that you read this manual to ensure your
safety. Failure to read this manual or follow its guidelines
could lead to serious injury or death.
3
RAPTOR DIAGRAM
SPECIFICATIONS
Compatibility: Most 6.5” hoverboards
Max Supported Weight: Refer to your hoverboard’s manual
Wheel Size: 4” swivel caster wheel
Seat Material: Polypropylene
1. Racing Flag
2. Bucket Seat
3. Handlebar (R)
4. Seat Frame
5. Lockers
6. Foot Rests
7. Caster Wheel
8. Fog Blaster & Mount
9. Dual Shocks
10. Handlebar (L)
11. Pedal Mounts
12. Adjustable Strap
13. Frame Extension
8
10
11
9
2
1
3
7
54
13 12
6
4
PARTS LIST
(1) Fog Blaster Mount
(1) Fog Blaster
(1) Charging Cable
(1) Seat
(1) Seat Frame with
Suspension
(1) Front Frame
(2) Lockers
(4) M8 X 38 Screws
(4) M6 X 16 Screws
(4) Mounting Screws
(4) 8 mm Nuts
(4) 6 mm Nuts
Tool Set:
AWrench
A
Hex Key and Screwdriver
B
B
(4) Hook & Loop
Straps with Rubber
Protectors
(1) Flag Set
(1) Flag Holder
(1) Right Handlebar
(1) Left Handlebar
ASSEMBLING YOUR RAPTOR
Remove all Raptor contents from the box. Ensure all contents from the “PARTS LIST” section are accounted
for.
1. Locate the seat fame. Move the 2 suspension shocks into the u-shaped holders at the rear of the seat
frame. You may need to twist the shocks to enure the holes at the end of the shocks align with the holes of
the u-shaped holders. Insert an M8 x 38 screw through each holder and cap each one with an 8 mm nut. Use
the hex key and hex wrench to make sure the lug nuts are completely tightened to the screws.
5
Please visit
x 2
Tools
needed
6
x 2
2. Insert the left and right handlebar mounts into the seat frame as shown below. Align the holes of the handlebar
mounts with the holes in the seat frame. Align the hole of the ag holder with the hole in the seat frame on either
side. This will be where the ag is inserted later. Insert the 8 X 38 screws into the seat frame holes and attach the 8
mm nuts to the end of the screws by twisting them on clockwise. Hold the screws in place with the hex key and
turn the nuts clockwise with the wrench to tighten them. Make sure the screws and nuts are tightly secured.
3. Insert the front frame into the seat frame. Adjust the front frame to your preferred length. Remove the black bolt
and the rst white washer from the end of each locker. Fully insert the screwed section of one locker into the seat
frame holes. Add the white washer and black bolt back onto the locker once it is fully inserted and twist them on
clockwise until they are tightly secured. Close the locker clamp tightly. Repeat these steps on the other side of the
seat frame with the other locker.
Tools
needed
7
4. Attach the fog blaster to the fog blaster mount as shown below. Screw in the 4 mounting screws using the
screwdriver at the end of the included hex key. Make sure the 2 larger holes of the fog blaster mount are facing
forward.
X 4
Tools
needed
5. At this point in the assebly, you should have the fog blaster xed on the mount, both handlebars xed to the seat
frame, the ag tube xed to the seat frame, and the front frame should be interlocked with the seat frame.
8
6. Align the holes of the bucket seat with the holes of the seat frame and fog blaster mount. Insert th M6 x 16 screws
into the holes in the bucket seat and cap each screw with a 6 mm nut. Hold the screws in place with the hex key
and turn the nuts clockwise with the wrench to tighten them until the bucket seat is secured.
7. Your Raptor is now assembled!
x 4
Tools
needed
Water
12
FOG BLASTER DIAGRAM
USING & MAINTAINING YOUR FOG BLASTER
1. Charging Port
2. Water Tank
3. Power Button
4. LED Lights & Sound Effects
Button
5. Fog Vent & LED Lights
5
3
Before using the fog blaster, connect the included charging cable to the fog blaster’s charging port and a
USB outlet (Figure 1). A red light will appear on the fog blaster while charging. When the light turns off, your
fog blaster is fully charged. A full change may take up to 4 hours. Unplug the charging cable. Next, press and
hold down the water tank buttons while pouring water into the water tank (Figure 2). Release the buttons
when the tanks are filled. Do not overfill!
Hold down the button to open
the water tank and pour
water into it
(Figure 1) (Figure 2)
1
2
4
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Hover-1 Hoverboard
Hover-1
Hover-1 MY FIRST HOVERBOARD Manuel utilisateur
Hover-1
Hover-1 RIVAL Instructions de fonctionnement
Hover-1
Hover-1 Beast Buggy Manuel utilisateur
Hover-1
Hover-1 i-100 Manuel utilisateur
Hover-1
Hover-1 SUPERSTAR EU-H1-SPR-CMB Instructions de fonctionnement
Hover-1
Hover-1 DRIVE Manuel utilisateur
Hover-1
Hover-1 DREAM Manuel utilisateur
Hover-1
Hover-1 FORMULA Manuel utilisateur
Hover-1
Hover-1 KART Manuel utilisateur
Hover-1
Hover-1 RANGER PRO Manuel utilisateur
