HotSpring ACE Manuel utilisateur

Contents

Welcome............................................................................1

Product Contents...............................................................1

Overview of the ACE System ............................................1

Spa Owner Responsibilities...............................................2

System Status ..................................................................2

Before Start-Up..................................................................3

ACE Water Care System Spa Water Guidelines ...............3

Start-Up and Refill Procedures..........................................3

Spa Model Table................................................................4

30-Day Check Up .............................................................5

Chlorine Boost ..................................................................6

Salt Test .............................................................................7

Cell Cleaning .....................................................................8

IQ 2020

®Remote Control (optional)................................8

Tips ....................................................................................8

Troubleshooting .................................................................9

Status/Service Messages ................................................10

Customer Service ............................................................10

Warranty ..........................................................................11

This Owner’s Manual will acquaint you with the operation of the ACE water care

system. We suggest that you carefully review the entire Owner’s Manual before us-

ing the ACE water care system. Please keep this manual available for reference. If

you have any questions about any aspect of your ACE water care system’s set-up,

operation, or maintenance, contact your authorized Hot Spring® dealer.

THE SPA OWNER IS ULTIMATELY RESPONSIBLE FOR

MAINTAINING PROPER SANITARY WATER CONDITIONS.

IMPORTANT:

When using the spa, the chlorine level must be maintained between 3-5 ppm.•

Ozone, Dichlor, MPS, and sliver are compatible with the ACE system.•

The ACE system is

•

NOT compatible with bromine or BaquaSpa®/biguanide.

Disclaimer: T

his is not an automatic water care system. The system is sized for

the typical user. Heavy users may need to supplement generation with dichlor or

MPS.

ACE Water Care System Page 1

Welcome

Congratulations on your purchase of the ACE water care system – a sanitizer

generating system that, when used as directed, makes it easy to keep spa water

sparkling clean.

Product Contents

Your ACE water care system includes:

Owner’s Manual•

Controller (a)•

Cell (b)•

Calcium Filter (c)•

Spa Salt (d)•

Installation Instructions•

NOTE:

Installation of the ACE water care system must be performed by an

authorized Hot Spring technician to insure proper operation.The ACE water care

system is compatible with all Hot Spring spas built after August 1, 2009. Your

local Hot Spring dealer can verify if your spa is ACE water care system-ready.

Purchase these items separately from your local Hot Spring dealer. Not included:

Hot Spring Freshwater Spa Care Kit – includes Concentrated Chlorinating•

Granules, MPS Oxidizer, pH Up, pH Down, Defoamer, Stain & Scale, 5-Way

Test Strips, and a Spa Water Maintenance & Troubleshooting Guide.

FreshStart10,000• ®Pre-Filter

Salt test strips (optional)•

Overview of the ACE System

The ACE water care system makes water care easy by:

Turning salt into powerful mixed oxidants like chlorine, ozone, and Potassium•

Peroxymonosulfate (MPS) to keep water crystal clear.

Generating the right amount of sanitizer needed based on spa size and use•

level – easily input through your spa’s control panel.

Testing for high or low salt levels, using the ACE system salt test.•

Increasing chlorine levels as needed with a convenient Boost function.•

Enjoy peace of mind while the illuminated water care icon and system status

messages on the spa’s main control panel tell you the ACE system is working. This

system greatly reduces the time and expense of maintaining your spa water, so you

can relax and enjoy.

abcd

Spa Owner Responsibilities

Balancing the pH level and Total Alkalinity to the “OK” range.Note: The•

generation of sanitizer from salt will cause the pH to drift upwards over time.

Check the pH level at least once a month and adjust as needed to maintain

water quality. An extensively high pH will cause premature failure of the system,

cloudy water, and decreased effectiveness of the sanitizer.

Maintaining low Hardness levels using the Watkins Calcium Filter as needed.•

Note: The ACE system works best with low levels of calcium and minerals in

the water. Softened water prolongs the equipment life, while enhancing the spa

experience. The ideal hardness level when using the ACE system is between

25 – 75 ppm.

Inputting spa size and spa use parameters.•

Check chlorine level weekly after initial start up to determine best Use Level to•

maintain healthy water quality.

Conduct a 30-day check up, including testing and balancing spa water, and•

confirming Use Level.

NOTE: The water care icon will flash as a reminder when the 30-day cycle is over.

Establishing a chlorine residual at start up.•

Manually flushing plumbing lines by super-chlorinating or “shocking” the spa monthly.•

IMPORTANT: Ensure that the chlorine level is always between 3-5 ppm before using

the spa. Add sodium dichlor manually if needed.

System Status

Water Care Icon – The water care icon, located on the icon bar below the

•

screen of the main control panel, will only be illuminated once the ACE

water care system is installed.

The icon will flash when

the ACE system requires

attention.

Status Messages – The ACE

•

system provides feedback via

the spa’s main control panel.

A status message will always

be displayed on the main ACE

water care system screen.

Refer to the Status/Service Messages section for a complete listing of

system status messages and their meanings.

Page 2 Watkins

Manufacturing Corporation

Before Start-Up

You will need a Hot Spring1. ®FreshWater®Spa Care Kit, which contains test

strips and balancers required each time you fill and refill your water along with a

FreshStart10,000®pre-filter, You can purchase these items from your local Hot

Spring dealer.

Fill your spa with fresh water using the FreshStart 10,000 Pre Filter.2.

NOTE: If you are not filling your spa for the first time, clean your filters with

FreshWater Filter Cleaner or replace with new filters, before refilling spa with

fresh water.

Once spa is filled, use a FreshWater test strip to measure the pH, Total Alkalinity,3.

and Hardness. Use the table below to determine if your spa water is in the “OK”

range.

ACE Water Care System Spa Water Guidelines

Parameter Target Min - ”OK” Range - Max

Salt 1000 ppm 750 1500

Hardness 50 ppm 25 ppm 75 ppm

Alkalinity 80 40 120

pH 7.4 7.0 7.6

Chlorine 3 3 5

Adjust pH and Total Alkalinity following instructions in the Water Quality and4.

Maintenance section of your spa’s Owner’s Manual.

To decrease the Hardness level of the water place the Calcium Filter over the5.

heater return at the bottom of the spa for up to 24 hours.

NOTE: The pH, Total Alkalinity and Hardness must be in the “OK” range as

indicated in the table above, before starting the ACE system.

Start-Up and Refill Procedures

At this point your spa should have balanced water, new or properly cleaned filters,

and power on.

STEP 1 – Add Salt

With the jets running, slowly add the directed amount of salt (see SPA MODEL1.

table on the following page) to the main tub, one cup at a time until all salt is

added.

Run jets an additional 5 minutes to ensure salt is totally dissolved. Note: After2.

adding the salt at start-up, the display may read low salt if water temperature

is low. Allow the spa to come to temperature (100-104F) before retesting or

adding salt.

ACE Water Care System Page 3

SPA MODEL TABLE

Spa Model Salt

(cups) or (grams)

Spa Size

Value

Vista

/ Summit* 6 1735 8

Grandee

6 1735 8

Envoy

5.75 1630 7

Aria

4.75 1410 6

Vanguard

5.25 1500 6

Sovereign

4.5 1360 6

Prodigy

4.25 1225 5

Jetsetter

2.75 820 3

* 50Hz Models only

STEP 2 – Access Water Care System menu

On the main control panel, press the1. Options hard button.

Press the2. Water Care soft button.

STEP 3 – Enter Use Level

In the Water Care System menu, press the1. Use Level soft button.

Adjust use level setting using the arrow soft buttons. The following are2.

approximate guidelines for determining use level.

a. 1 = Low bather load (1 person less than 1 hour per week, vacation mode).

b. 2–4 = Normal bather load (1-2 persons less than 3 hours per week).

c. 5 = High bather load (2 or more persons more than 3 hours per week).

Adjusting the Use Level will cause the value on the screen to flash. Once the3.

correct Use Level is displayed, press the Confirm? soft button to enter your

selection. The value will stop flashing, and the “?” next to the word Confirm

will disappear.

Recommended initial setting: USE 4

Press the4. BACK hard button to return to the main menu.

RECOMMENDED: Following initial start-up, test the chlorine level of your spa once a

week. Adjust the Use Level up if the chlorine level is low, or down if the chlorine level

is high, to find the level that produces a stable chlorine level of 3-5 ppm. This will

help maintain water quality.

STEP 4 – Set Spa Size

Determine the value (1-8) associated with your spa model using the Spa1.

Model Table.

In the Water Care System menu, press the2. Set-up soft button.

Press the3. Spa Size soft button.

Page 4 Watkins

Manufacturing orporation

ACE Water Care System Page 5

Adjust spa size using the soft buttons next to the arrows.4.

Adjusting the Spa Size will cause the value on screen to flash. Once the5.

correct Spa Size is displayed, press the Confirm? soft button to enter your

selection. The value will stop flashing, and the “?” next to the word Confirm

will disappear.

Once Spa Size has been selected, press6. Confirm? soft button to enter your

selection.

Press the7. BACK hard button to return to the main menu.

STEP 5 – Test for chlorine and establish residual

Once your spa is programmed, check chlorine level with a FreshWater test strip.1.

Add granular sodium dichlor, as directed on the bottle, to 5ppm as described in2.

the spa’s Owner’s Manual to create a sanitized residual until the ACE system

is generating sanitizer at full capacity.

Allow jets to run 5 minutes per jet system (rotating the diverter valves).3.

NOTE: Ensure that Calcium Filter is repositioned after running jets

STEP 6 – Remove Calcium Filter after 24 hours – discard.

IMPORTANT: Do not use the spa until the chlorine is between 3-5 ppm.

30-Day Check-up

You must check your spa water at least once every 30 days. To remind you, the ACE

water care icon will flash and the status message will read, “Monthly Maintenance”

at the end of the 30-day cycle. The 30-day cycle re-starts after you confirm the use

level.

STEP 1

Use a FreshWater test strip to measure the pH, Total Alkalinity, and Hardness.1.

Use the Spa Water Guidelines in this manual to determine if your spa water is

in the “OK” range.

Adjust pH and Total Alkalinity following instructions in the Water Quality and2.

Maintenance section of your spa’s Owner’s Manual.

To decrease the Hardness level of the water place a new Calcium Filter over3.

the heater return at the bottom of the spa for 24 hours.

STEP 2 – Access Water Care system menu

Press the1. Options hard button, followed by the Water Care soft button on the

spa’s main control panel.

STEP 3 – Enter Use Level

In the Water Care system menu, press the1. Use Level soft button

Adjust use level setting using the arrow soft buttons. The following are2.

approximate guidelines for determining use level.

a. 1 = Low bather load (1 person less than 1 hour per week, vacation mode).

b. 2–4 = Normal bather load (1-2 persons less than 3 hours per week).

c. 5 = High bather load (2 or more persons more than 3 hours per week).

Adjusting the Use Level will cause the value on screen to flash. Once the3.

correct Use Level is displayed, press the Confirm? soft button to enter

your selection. The value will stop flashing, and the “?” next to the word

Confirm will disappear.

Press the4. BACK hard button to return to the main menu.

NOTE: You must set and confirm the Use Level even if it’s the same as the prior setting.

STEP 4 – Shock Spa and Plumbing Lines

Use a Freshwater Test strip to measure chlorine levels.1.

Increase chlorine level to 3-5 ppm using granular sodium dichlor.2.

Activate spa’s automatic clean cycle using the main control panel.3.

Chlorine Boost

If the spa is being used more often than usual, it may be necessary to add more

chlorine to the water by “boosting” the ACE system. To increase the chlorine level:

Access the1. Water Care system menu by pressing the Options hard button,

followed by the Water Care soft button on the spa’s main control panel.

Press the2. Boost soft button.

Press the3. Yes soft button to confirm the manual Boost operation.

The system will automatically initiate a salt test before the Boost. Once salt4.

test is complete status will display "Water Care System Boosting" when active.

IMPORTANT: It may take up to 24 hours to complete the Boost cycle. The

chlorine level must be maintained between 3-5 ppm at all times. Manually add

sodium dichlor if necessary for regular use or shocking the spa.

Page 6 Watkins

Manufacturing Corporation

Salt Test

The ACE system automatically tests the water’s salt level. A manual Salt Test is only

required if the water care icon is flashing and the status screen indicates High salt or

Low salt levels.

To conduct a manual Salt Test:

Access the Water Care system menu by pressing the1. Options hard button,

followed by the Water Care soft button on the spa’s main control panel.

Press the2. Set-up soft button, followed by the Salt Test soft button.

Note location of the salt level indicator on screen.3.

Press4. Yes soft button to start the salt test and wait 20 seconds for the test

to complete.

a. If proper amount of salt is present, screen will display “Water Care

System Functioning”.

b. If “High Salt” or “Low Salt” is still displayed proceed as follows:

For Low Salt –

i. If the cell is new, or has just been cleaned, review the location

of the salt indicator to determine how low the salt level is.

ii. Add (1) cup of salt to the water and circulate for 5 minutes.

Activate a second salt test and repeat the process as needed.

iii. If 50% of the spa’s recommended salt has been added and

icon continues to flash, contact your Hot Spring Service

Professional for assistance.

NOTE:

A low salt reading may indicate the need to clean the ACE cell.

For High Salt –

i. Review the location of the salt indicator to determine how high

the salt level is.

ii. Drain 25% of the water from the spa and refill with clean clear

water.

NOTE: If salt indicator is above 50% in the red indicator, drain

completely and refill. (See Start-up and Refill Procedure)

iii. Run the jet pumps for 5 minutes and then conduct another

manual Salt Test.

iv. The salt level will be displayed as OK when the salt is in

range. Repeat as needed.

ACE Water Care System Page 7

Cell Cleaning

Periodic cleaning of the ACE cell is recommended to maximize the life of your

equipment. Use of the Calcium Filter will help reduce the cleaning frequency. When

the status message on the screen indicates low salt and the water has not been

changed or topped off recently, it maybe time to clean the cell.

Turn off the power to the spa. Open the spa cover and remove the filter lid.1.

Unscrew gray filter cap and gently pull the cell out of the filter.2.

Fill a 16oz cup half way with vinegar.3.

Place the cell in the cup ensuring that the bottom of cell is floating.4.

Add more vinegar as needed to cover the cell by 1” (2 cm).5.

Soak the cell for 15 minutes or until bubbles stop coming from the cell. If6.

bubbles are still releasing from the cell after 15 minutes, change the

vinegar and repeat.

Replace cell into filter standpipe ensuring it reaches the bottom of the7.

standpipe. Screw on gray filter cap lid, replace filter lid, power up the spa.

Ensure that the cell goes all the way down the pipe.

IQ 2020

®Remote Control (Optional Accessory)

The IQ 2020 remote control has the same control capability as the spa’s main

control panel.

To access the ACE system menus, press the MODE button until1. CHEM+

is displayed on the screen.

Press the (+) button to enter into the ACE system menus. The word2. ADD

will appear on the screen.

Press the MODE button to scroll through the ACE system menus.3.

To change a setting, find the desired menu, press the (+) button to enter4.

that menu. Press the (+) again to change the setting. Press the (-) button

once to set a new setting, and a second time to confirm.

To exit the ACE system menus, press the MODE button until the5. EXIT

screen is displayed. Press the (+) button to exit.

Tips

Vacation or limited use.• When the spa is not going to be in use, shock the

spa by increasing chlorine to 3-5 ppm and then run the automatic clean cycle.

Clean or replace filters. Lower Use Level setting to 1.

Water Changes.• Because the ACE water care system reduces the amount of

chemicals added to the spa water, it is possible to extend the life of the water

2 to 4 times depending on use level. Test your water regularly to ensure safety.

Page 8 Watkins

Manufacturing Corporation

Autres manuels pour ACE

Table des matières

Autres manuels HotSpring Système d'eau

HotSpring

HotSpring ACE Manuel utilisateur

Manuels Système d'eau populaires d'autres marques

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur

Microline

Microline T.F.C.-4 Manuel

Eureka Forbes

Eureka Forbes Aquaguard Select Manuel utilisateur

Cetetherm

Cetetherm AquaEfficiency Manuel utilisateur

CB Tech

CB Tech CB-VOC Manuel utilisateur

Vaillant

Vaillant auroFLOW plus VPM 15 D Manuel utilisateur

resideo

resideo Braukmann HS10S Manuel utilisateur

Gude

Gude INOX 100/24 Manuel utilisateur

Mono

Mono Eco 1-60 Manuel

SpectraPure

SpectraPure Drinking Water Kit Manuel utilisateur

HydroCare

HydroCare Dual Action Manuel utilisateur

NEXT pool

NEXT pool STERILOR Cu/Ag Schéma de câblage

Alpha

Alpha SolarSmart 150 Guide de l'utilisateur

TA FRISTAR3 Manuel utilisateur

GÜDE

GÜDE HWA 800 K Manuel utilisateur

Rainfresh

Rainfresh UCS2 Manuel utilisateur