Host T7 Manuel utilisateur

T7/T71/T73

M40000/M40001/M40003

REPAIR PARTS CATALOG NO. M30202(R)

For Machines with Serial No. T6183-T9031

ISSUED July 2009

ORDERS

Please use Part Numbers when ordering and include the

the machine Serial Number (found on the electrical data

plate) to insure that you will receive the correct parts.

Order from your HOST Distributor.

Parts Catalog

Racine International, LLC. 1-262-637-4491

1405 Sixteenth Street

P.O. Box 1648

1-800-558-9439

Racine, WI 53401 USA www.hostdry.com

FAX 1-262-637-0558

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

WHEN USING ELECTRICAL EQUIPMENT, BASIC PRECAUTIONS SHOULD ALWAYS

BE FOLLOWED, INCLUDING THE FOLLOWING:

WARNING–TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

1. Do not leave machine when plugged in. Unplug from outlet when not in use and before

servicing.

2. Do not use outdoors or on wet surfaces.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in manufacturer’s Instruction Manual. Use only manufacturer’s

recommended attachments.

5. Inspect cord for damage before each use. Do not use with damaged cord or plug. If machine

is not working as it should, has been dropped, damaged, left outdoors,or dropped into water,

return it to the manufacturer or authorized repair center.

6. Do not pull or carrybycord, use cord as a handle,close a door on cord, or pull cord around

sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug not the cord.

8. Do not handle plug or machine with wet hands.

9. Do not put any object into openings. Do not use with any opening blocked; keep free of dust,

lint, hair, and anything that may reduce air ﬂow.

10. Keep hair, loose clothing, ﬁngers, and all parts of body away from openings and moving parts.

11. Turn off all controls before unplugging.

12. Use extra care when cleaning on stairs.

13. Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas

where they may be present.

14. Do not use to pick up anything that is burning or smoking, such as cigarettes, matches,

or hot ashes.

15. Do not use for picking up health-endangering dust such as asbestos.

16. Do not use as a wet vacuum.

17. Do not use without ﬁlters in place.

18. Connect to a properly grounded outlet only. See Grounding Instructions.

19. This machine is to be used with HOST®carpet cleaning products only. Use of other cleaning

products may damage this machine.

I 2SNOITCURTSNIYTEFASTNATROPM

This machine must be grounded. If it should malfunction or break down, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This machine is

equipped with a cord having an equipment-grounding conductor and grounding plug. The plug

must be inserted into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

WARNING: Improper connection of the equipment-grounding conductor can result in the risk of

electric shock. Check with a qualiﬁed electrician or service person if you are in doubt as to whether

the outlet is properly grounded. Do not modify the plug provided with the machine.If it will not ﬁt

the outlet, have a proper outlet installed by a qualiﬁed electrician.

This machine is for use on a nominal 120 volt circuit, and has a grounded plug that looks like

the plug illustrated in Diagram A. A temporary adapter that looks like the adapter illustrated in

Diagram B may be used to connect this plug to a 2-pole receptacle as shown in Diagram C if

a properly grounded outlet is not available. The temporary adapter should be used only until a

properly grounded outlet can be installed by a qualiﬁed electrician. The green colored rigid ear,

lug, or the like extending from the adapter as illustrated in Diagram B,must be connected to a

permanent ground outlet box cover. Whenever the adapter is used, it must be held in place by a

metal screw as shown in Diagram C.

Note: In Canada, the use of a temporaryadapter is not permitted by the Canadian Electrical Code.

GROUNDING INSTRUCTIONS 3

GROUNDED OUTLET BOXES

(A)

GROUNDING PIN

)C()B(

METAL

SCREW

ADAPTER

TAB FOR

GROUNDING

SCREW

1405 Sixteenth Street P.O. Box 1648 Racine, Wisconsin 53401 1-800-558-9439 1-262-637-4491 FAX 1-262-637-0558 www.hostdry.comRacine International, LLC.

Safety Instructions __________________________________________________ 2

Grounding Instructions ______________________________________________ 3

Section I - T7/T71/T73 Parts __________________________________________ 5

Operating Handle Assembly __________________________________________ 6/7

Lifting Handle Assembly ______________________________________________ 8/9

Motor Case Assembly ________________________________________________ 10/11

Outer Gear Case Assembly __________________________________________ 12/13

Inner Gear Case Assembly ____________________________________________ 14/15

Motor Shroud Assembly ______________________________________________ 16/17

Nozzle/Inner Hood Assembly __________________________________________ 18/19

Brush & Tray Assembly ______________________________________________ 20/21

Wiring Diagram - 100/120V ____________________________________________ 22

Wiring Diagram - 220/240V ____________________________________________ 23

Section II - M40000/M40001/M40003 VAC Parts____________________________ 25

TABLE OF CONTENTS 4

S 5STRAP37T/17T/7T-INOITCE

Racine Industries Inc. 1405 Sixteenth Street P.O. Box 1648 Racine, Wisconsin 53401 1-800-558-9439 1-262-637-4491 FAX 1-262-637-0558 www.hostdry.comRacine International, LLC.

O 6YLBMESSAELDNAHGNITAREP

OPERATING HANDLE ASSEMBLY 7

Code No. Part No. Description

M30592 Operating Handle Assembly

(Includes Code Nos. 1-6)

1 M30591 Handle, Pinned & Welded

2 K1031 Cord Hook (2 Required)

3 K1030 Cord Clip (T7)

4 M7053B Screw 10-32 x 3⁄8"(4 Required)

5 M30600 Tube Plug

6 M30604 Foam Grip

*Not Illustrated M30595 Strain Relief (T71)

Racine Industries Inc. 1405 Sixteenth Street P.O. Box 1648 Racine, Wisconsin 53401 1-800-558-9439 1-262-637-4491 FAX 1-262-637-0558 www.hostdry.comRacine International, LLC.

LIFTING HANDLE ASSEMBLY 8

LIFTING HANDLE ASSEMBLY 9

Code No. Part No. Description

1 M30140 Decal, Handle Release

2 M30101 Plunger, Handle Release

3 M30117 Spring

4 M30104 Retaining Ring 1⁄4" Shaft

5 M30100 Retainer, Handle Release

6 M30553 Handle Support

7 M30456 Lifting Handle Weldment

8 M30281 Screw 10-32 x 1⁄2"(2 Required)

9 M6419A Screw 10-32 x 11⁄2" (T7/T71)

10 D277 Lockwasher #10

11 M30556 Lock Shaft Assembly

12 M30098 Retainer, Temporary Detent

13 M30102 Spring

14 M30182 Temporary Detent

15 603 Lockwasher 1⁄4"(2 Required) (T7/T71)

16 L5002 Screw 1/4-20 x 3⁄4"(2 Required)

17 M30452 Flange Bearing

18 M30555 Set Screw8-32 x 1⁄4"

19 M30525 Washer, Flat (T7/T71)

20 M30365 Handle Release Assembly

21 M30378 Insulator Tube (2 Required)

22 M30201 Washer, Flat

23 M30554 Lifting Handle Assembly

T73 ONLY

24 W529 Washer, Flat Nylon (2 Required)

25 M7053B Screw 10-32 x 3⁄8"

26 M30377 Insulator

27 75 Set Screw 10-32 x 3⁄4"

Racine Industries Inc. 1405 Sixteenth Street P.O. Box 1648 Racine, Wisconsin 53401 1-800-558-9439 1-262-637-4491 FAX 1-262-637-0558 www.hostdry.comRacine International, LLC.