Honeywell RedLINK Manuel utilisateur
RedLINK™Wireless System
With TrueZONE™Panel & Wireless Adapter
® U.S. Registered Trademark.
Copyright © 2012 Honeywell International Inc.
All rights reserved.
Provides wireless control of TrueZONE Panels. (See zone panel information
for heat/cool stage capacity. )
DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical
shock or equipment damage.
MERCURY NOTICE: If this product is replacing a control that contains mercury in a sealed
tube, do not place the old control in the trash. Contact your local waste
management authority for instructions regarding recycling and proper disposal.
Must be installed by a trained, experienced technician. Read these instructions care-
fully. Failure to follow these instructions can damage the product or cause a
hazardous condition.
69-2090EFS-07
Français : voir la page 17 • Español: vea la página 32
Installation guide for:
• FocusPRO®wireless thermostats
• Wirelessremotecontrol
• Wirelessoutdoorairsensor
System
Installation
Guide
RedLINK™ Installation Guide (TrueZONE™)
69-2090EFS—07 2
System installation at a glance
Installation procedure
This document covers linking and installation procedures for FocusPRO wire-
less thermostats and RedLINK accessories in TrueZONE applications.
Before you begin, you must mount, wire & configure the TrueZONE panel
and wireless adapter (see TrueZONE Installation Guide), then follow steps
below.
You must configure the TrueZONE panel before you begin
Install batteries in wireless devices....................................Page 3
Link all devices to wireless network ..............................Pages 3-5
Exit wireless setup..............................................................Page 6
Customize thermostat (installer setup)........................Pages 6-10
Mount thermostat and outdoor sensor .............................Page 11
To replace system components if needed, see page 13
3
5
4
2
1
If you have more than one TrueZONE Panel: Thermostats are linked to specific zone
panels. Optional accessories must be linked to each zone panel separately.
M33903
OUTDOOR
AIR SENSOR
HVAC
EQUIPMENT
THERMOSTAT
THERMOSTAT
REMOTE
CONTROL
Tr ueZONE
PANEL
WIRELESS
ADAPTER
Français : voir la page 17 • Español: vea la página 32
3 69-2090EFS—07
Install batteries in wireless devices
1
When system wiring is complete and TrueZONE panel is configured for RF,
install batteries in all devices. Make sure batteries are inserted properly (see
illustrations below).
Link all devices to wireless network
2
Make sure the Connected light on the
wireless adapter is flashing green.
If the light stops flashing before you have
linked all devices, press connect again.
MCR33901
Press connect
Flashing status light times out after 15
minutes of inactivity. Press connect again if
necessary.
Continued on next page >>
If light does not flash, another EIM/wireless
adapter may be in wireless setup mode. Exit
wireless setup at the other EIM/wireless adapter.
M28474
Thermostat
M28472
M28473
Install quick reference cardInstall 2 fresh AA
batteries
MCR32939
Remote control (optional) Outdoor air sensor (optional)
M28444
Install 3 fresh AA
batteries
Install 2 fresh AA
lithium batteries
Programmable models only
RedLINK™ Installation Guide (TrueZONE™)
69-2090EFS—07 4
M28479
Wireless Setup
Connect
Back
M28478
36
52
Wireless Setup
Next
Back
M28497
0
1
Wireless Setup
Next
Press sor tto set a zone number for this
thermostat (1 to 4), then press next.
Press sor tto change the name or
location of this zone, then press next.
Example: 31 = Living room
Press connect to establish a link to the wire-
less network.
After a brief pause, the confirmation screen
at left should be displayed, to
verify that the wireless connection has been
established.
Press done to display the home screen.
Zone number
Zone name
If E1 appears, see error codes on page 12.
See complete zone list on page 8
Link thermostats to wireless network
M28480
Wireless Setup
Connected
Done
Français : voir la page 17 • Español: vea la página 32
5 69-2090EFS—07
Link remote control to wireless network (optional)
Link outdoor sensor to wireless network (optional)
1Make sure the Connected light on the
wireless adapter is flashing.
2Press the connect button on the back of
the sensor.
3Check thermostat to verify that the out-
door sensor is working. After about 15
seconds, the thermostat should display
outdoor temperature and humidity.
(If you are installing more than one zone
panel, repeat steps 1-3 for each.)
MCR28847A
Press and release
1Make sure the Connected light on the
wireless adapter is flashing.
2Press connect at the remote. There will
be a short delay as the remote seeks a
signal from the wireless network.
3When the screen displays “Connected,”
press done.
4Press no at the next screen to save and
exit. (Or press yes and repeat steps 1-4
to link another zone panel.)
If E1 appears, see error codes on page 12.
MCR32942
CONNECT
WIRELESS SETUP
MCR33902
NO
YES
CONNECT MORE?
The linking procedure may time out if there is
no keypress within 30 minutes. To begin again,
press and hold the blank space (or arrow if pres-
ent) in the lower right corner of the screen until
the display changes (about 3 seconds)
Press to link another
zone panel
Press to save
and exit
RedLINK™ Installation Guide (TrueZONE™)
69-2090EFS—07 6
M28487
1
0
Next
Back
Done
Customize thermostat (installer setup)
4
Function Setting
Press sor tto change setting
(see tables on pages 7-9)
Press next to display next
function screen
Press done to save & exit.
Follow the steps below to begin installer setup. At each function screen, press
sor tto change the setting as desired, then press next to advance to the next
function screen.
See tables on pages 7-9 for a description of options for each function.
FAN
M28485
To begin, press and hold the fan and sbuttons
until the display changes (about 3 seconds).
Exit wireless setup
3
Press connect at the wireless adapter to exit wireless setup (light should stop
flashing).
Note: The wireles adapter will automatically exit wireless setup after 15 minutes of
inactivity.
Note: If installing more than one zone panel, you must exit wireless setup before installing an
additional zone panel.
M28498
0
1
Next
Back
Done
Français : voir la page 17 • Español: vea la página 32
7 69-2090EFS—07
Installer setup tables
0
1
2
3
5
6
7
8
9
10
12
13
14
Zone number
System type
Changeover valve
(O/B terminal)
Fan control
(conventional heat)
Stage 1 heat cycle
rate (CPH= cycles
per hour)
Stage 2 heat cycle
rate (CPH)
Stage 3 heat cycle
rate (CPH)
Emergency heat
cycle rate (CPH)
Stage 1 compres-
sor cycle rate
Stage 2 compres-
sor cycle rate
Manual/Auto
changeover
Adaptive Intelligent
Recovery
Temperature
display
0 No zoning (single thermostat used with THM5320R EIM)
[Options: select zone 1, 2, 3 or 4]
0 1 heat/1 cool conventional
1 1 heat/1 cool heat pump (no aux. heat)
2 Heat only (includes Series 20)
3 Heat only with fan
4 Cool only
5 2 heat/1 cool heat pump
6 2 heat/2 cool conventional
7 2 heat/1 cool conventional
8 1 heat/2 cool conventional
9 2 heat/2 cool heat pump
10 3 heat/2 cool heat pump
0 O/B terminal controls valve in cooling
1 O/B terminal controls valve in heating
0 Gas/Oil heat (equipment controls fan)
1 Electric furnace (thermostat controls fan)
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
5 Gas or oil furnaces (less than 90% efficiency)
1 Steam or gravity systems
3 Hot water systems & furnaces of over 90% efficiency
9 Electric furnaces
[Cycle rate options: 1 to 12 CPH]
9 Electric furnace
[Cycle rate options: 1 to 12 CPH]
3 Recommended cycle rate
[Cycle rate options: 1 to 6 CPH]
3 Recommended cycle rate
[Cycle rate options: 1 to 6 CPH]
0 Manual (User options: Heat/Cool/Off)
1 Automatic (User options: Heat/Cool/Auto/Off)
Applies only to Model TH6320
0 Off **
1 On
0 Fahrenheit
1 Celsius
** See page 9
Setup functions Settings & Options (factory default in bold)
RedLINK™ Installation Guide (TrueZONE™)
69-2090EFS—07 8
15
16
26
27
28
32
33
35
Compressor off
time (minimum)
Schedule format
Auxiliary heat
control
Maximum heat
setpoint
Minimum cool
setpoint
Temp. display
offset (indoor)
Temp. display
offset (outdoor)
Humidity display
offset (outdoor)
5 5 minute compressor off time **
[Options: 0 to 4 minutes]
Applies only to Model TH6320
0 Weekday/weekend program schedule
1 Weekday/Saturday/Sunday program schedule
Applies only to Model TH5320
0 Comfort **
1 Economy
90 Max. heat temperature setting is 90°F (32°C)
[Options: 40 to 90°F (4.5 to 32°C)]
50 Min. cool temperature setting is 50°F (10°C)
[Options: 50 to 99°F (10 to 37°C)]
0 Thermostat displays actual temperature
[Options: -3 to +3°F offset (-1.5 to +1.5°C)]
0 Thermostat displays actual temperature
[Options: -5 to +5°F offset (-2.5 to +2.5°C)]
3 Thermostat displays actual humidity
[Other options: 0 = -15%, 1 = -10%, 2 = -5%,
4 = 5%, 5 = 10%, 6 = 15% offset]
Installer setup tables
Setup functions Settings & Options (factory default in bold)
36
39
90
Zone name
Wireless setup
RESET
52 Thermostat
0 Disconnect thermostat from wireless system
1 Thermostat is connected to wireless system
0 No reset
1 Reset installer options & program schedule to factory default
settings
** See page 9
1 Basement
2 Bathroom
3 Bathroom 1
4 Bathroom 2
5 Bathroom 3
6 Bedroom
7 Bedroom 1
8 Bedroom 2
9 Bedroom 3
10 Bedroom 4
11 Boat House
12 Bonus Room
13 Computer Room
14 Den
15 Dining Room
16 Exercise Room
17 Family Room
18 Fireplace
19 Foyer
20 Game Room
21 Garage
22 Great Room
23 Guest Room
24 Gym
25 Kid’s Room
26 Kitchen
27 Kitchen 1
28 Kitchen 2
29 Laundry Room
30 Library
31 Living Room
32 Lower Level
33 Master Bath
34 Master Bed
35 Media Room
36 Music Room
37 Nursery
38 Office
39 Office 1
40 Office 2
41 Pantry
42 Play Room
43 Pool Room
44 Porch
45 Rec Room
46 Sewing Room
47 Spa
48 Storage Room
49 Studio
50 Sun Room
51 Theater
52 Thermostat
53 Upper Level
54 Utility Room
55 Walk In Closet
56 Wine Cellar
57 Workshop
Français : voir la page 17 • Español: vea la página 32
9 69-2090EFS—07
Special functions
Adaptive Intelligent Recovery (Setup Function 13): Allows the thermostat to “learn” how long the
furnace and air conditioner take to reach programmed temperature settings, so the
temperature is reached at the scheduled time.
Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes before
restarting, to prevent damage. During this time, “Heat On/Cool On” flashes on the display.
Comfort/Economy (Setup Function 26):
If you choose Comfort, auxiliary heat will respond quickly to meet the temperature setpoint. If you
choose Economy, the system will wait longer. Auxiliary heat will be activated only if the setpoint is
not reached within a reasonable time.
RedLINK™ Installation Guide (TrueZONE™)
69-2090EFS—07 10
M28489
02
0
Next
Back
Done
System test
M28488
To begin, press and hold the sand tbuttons
until the display changes (about 3 seconds)
Press sor t to check system status
Press next to advance to next test
Press done to terminate system test
02
10
20
30
40
70
Wireless test
Heating system
Emergency
heating system
Cooling system
Fan system
Thermostat
information
(for reference only)
0 Off
1 Test radio signal (after a brief pause, screen displays 1-10
to show signal strength; 5 or higher recommended)
0 Heat and fan turn off
1 Heat turns on
2 Stage 2 heat turns on
3 Stage 3 heat turns on
0 Heat and fan turn off
1 Heat and fan turn on
0 Compressor and fan turn off
1 Compressor and fan turn on
2 Stage 2 compressor turns on
0 Fan turns off
1 Fan turns on
71 Software revision number (major revisions)
72 Software revision number (minor revisions)
73 Configuration identification code (major)
74 Configuration identification code (minor)
75 Production configuration date code (week)
76 Production configuration date code (year)
System Test System Status
Follow the procedure below to test for proper operation.
System test
number
System
status
CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection (minimum off time)
is bypassed during testing. To prevent equipment damage, avoid cycling the compressor
quickly.
Autres manuels pour RedLINK
4
Table des matières
Langues :
Autres manuels Honeywell Thermostat
Honeywell
Honeywell VisionPRO 8000 Series Manuel utilisateur
Honeywell
Honeywell Y9420S Manuel utilisateur
Honeywell
Honeywell FocusPRO TH5110D Manuel utilisateur
Honeywell
Honeywell T841A Manuel utilisateur
Honeywell
Honeywell RTH7400 series Manuel utilisateur
Honeywell
Honeywell Round T87K Manuel utilisateur
Honeywell
Honeywell T8400 Manuel utilisateur
Honeywell
Honeywell VisionPRO Wi-Fi TH8320WF Mode d’emploi
Honeywell
Honeywell THP2400A1019 Manuel utilisateur
Honeywell
Honeywell T834C Manuel utilisateur
Honeywell
Honeywell HE0118 Manuel utilisateur
Honeywell
Honeywell RTH6300B Manuel utilisateur
Honeywell
Honeywell RTH2510 Series Manuel utilisateur
Honeywell
Honeywell TH7000 Series Manuel utilisateur
Honeywell
Honeywell TP970 Series Manuel utilisateur
Honeywell
Honeywell 2080WL Manuel d'utilisation
Honeywell
Honeywell TH9421C1004 Manuel utilisateur
Honeywell
Honeywell Deluxe Manuel utilisateur
Honeywell
Honeywell VT15 Manuel utilisateur
Honeywell
Honeywell PRO 1000 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
Sinope
Sinope TH1300RF Manuel utilisateur
NuTone
NuTone NTBZ48 Instructions d'utilisation d'origine
Stelpro
Stelpro MAESTRO ASMT402AD Manuel utilisateur
Aube Technologies
Aube Technologies TH305 Manuel utilisateur
Powtier Controls
Powtier Controls 505MST Manuel utilisateur
Kanmor
Kanmor Zone Control 369e Manuel utilisateur