Honeywell INNCOM E528.4G Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Honeywell Thermostat

Honeywell

Honeywell T5+ Manuel utilisateur

Honeywell

Honeywell HH07AT216 Manuel utilisateur

Honeywell

Honeywell TRADELINE T8400C Manuel utilisateur

Honeywell

Honeywell FocusPRO 5000 Manuel utilisateur

Honeywell

Honeywell VTL120 Manuel utilisateur

Honeywell

Honeywell RTH6500WF Wi-Fi Series Manuel utilisateur

Honeywell

Honeywell T87F Manuel utilisateur

Honeywell

Honeywell Evohome Manuel utilisateur

Honeywell

Honeywell T6R-HW Manuel utilisateur

Honeywell

Honeywell Prestige IAQ Instructions d'installation et d'utilisation

Honeywell

Honeywell HEAT PUMP THERMOSTAT T8411R Manuel utilisateur

Honeywell

Honeywell T8601D Manuel utilisateur

Honeywell

Honeywell T8000C Manuel utilisateur

Honeywell

Honeywell RTH7400 series Manuel utilisateur

Honeywell

Honeywell RTH7500 Series Manuel utilisateur

Honeywell

Honeywell TH115-AF-GA Manuel utilisateur

Honeywell

Honeywell T641A Manuel utilisateur

Honeywell

Honeywell TRUEZONE HZ322 Manuel utilisateur

Honeywell

Honeywell Lyric Enrollment Manuel utilisateur

Honeywell

Honeywell CHRONOTHERM IV DELUXE T8624D Manuel d'utilisation

Honeywell

Honeywell RTH6400 Series Manuel utilisateur

Honeywell

Honeywell T4360G Manuel utilisateur

Honeywell

Honeywell PRO TH4000 series Manuel utilisateur

Honeywell

Honeywell RTH6350 Series Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur

Aube Technologies

Aube Technologies TH305 Manuel utilisateur

Powtier Controls

Powtier Controls 505MST Manuel utilisateur

Kanmor

Kanmor Zone Control 369e Manuel utilisateur

Page 1 - Set RID, PAN ID and RF Channel in E528.4G and E527.4G

Set Room ID, PAN ID and RF Channel in INNCOM

E528.4G and E527.4G Thermostats

Enter Service Mode

Service mode is accessed by executing the following button sequence:

1. Press and hold F/C.

2. Press and release OFF/AUTO.

3. Press and release DISPLAY.

4. Release F/C.

The LCD display will now read “rid” confirming that you are in service mode.

Set Room ID

A unique 5-digit Room ID is required in each INNCOM thermostat.

Enter Service Mode and follow the procedure below to set the Room ID of the thermostat.

1. Scroll to rId

2. Press DISPLAY button and the current Room ID will scroll on the display.

3. After the Room ID scrolls, the highest digit of the Room ID will be displayed with the

HI fan indicator. Use the up or down arrow buttons to change the value and press

OFF/AUTO.

4. The next 2 digits of the Room ID are now displayed along with the MED fan indicator.

Use the up or down arrow buttons to change the value and press OFF/AUTO.

5. The last 2 digits of the Room ID are now displayed along with the LO fan indicator

Use the up or down arrow buttons to change the value and press OFF/AUTO.

6. Press the DISPLAY button to store the new Room ID. The new Room ID will scroll

across the display.

Example of RID for Room 515 (00515)

Page 2 - Set RID, PAN ID and RF Channel in E528.4G and E527.4G

Set PAN ID

PAN ID is the Personal Area Network ID of the thermostat. The PAN ID is used in networked

systems where the PAN ID of the thermostat must match the PAN ID of the router it is

assigned to.

Enter service mode and follow the procedure below to set the PAN ID in the thermostat

1. In Service Mode, go to PAn and press DISPLAY to view the value.

2. Change the displayed value to the assigned PAN ID and press the DISPLAY button to

set. The thermostat will beep to indicate the value has been entered.

Set RF Channel

The RF channel is used for both in-room RF communication and RF network

communication. In most cases the default RF channel of 26 will be used. In networked

systems, the RF channel in the thermostat must match the RF channel in the router it is

assigned to.

Enter service mode and follow the procedure below to set the RF Channel in the thermostat

1. In Service Mode, go to rf and press DISPLAY to view the value.

2. Change the displayed value to the assigned RF channel and press the DISPLAY

button to set. The thermostat will beep to indicate the value has been entered.

Exit Service Mode

Press F/C to exit service mode. You may need to press F/C multiple times to fully exit

from submenus within service mode.