Honeywell H7625B Manuel utilisateur

INSTALLATION INSTRUCTIONS

63-2579—3

H7625B; H7635B,C; H7655B

Duct-Mount and Outdoor-Mount

Humidity/Temperature Sensors

APPLICATION

The H7625B, H7635B, H7655B Duct-Mount and H7635C

Outdoor-Mount Humidity/Temperature Sensors are

universal Relative Humidity transmitters that can be

powered with either a +18 to 36 Vdc or 24 Vac supply.

The sensors use a half-wave bridge rectifier to convert

AC power to a usable DC voltage. The device also

includes a 20K ohm temperature sensor for optional use.

The humidity sensors are designed with a field-

selectable4to20mA,0to5Vdc,or0to10Vdcoutput

signal equivalent to 0 to 100% RH. All units are shipped

from the factory with a default setting to accept AC power

with three-wire, 0 to 10 Vdc loop-powered output.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a

hazardous condition.

2. Check ratings given in instructions and on the

product to ensure the product is suitable for your

application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Electrical Shock or Equipment Damage

Hazard.

Can shock individuals or short equipment

circuitry.

Disconnect power supply before installation.

CAUTION

Equipment Damage Hazard.

Improper wiring can damage the sensor

beyond repair.

Follow the wiring instructions carefully.

Mounting

The method of mounting depends on the particular

sensor application. The following procedures include

outdoor and duct applications. Also refer to the

instructions for the electronic control.

Duct Mounting

The H7625B, H7635B and H7655B can be mounted in a

duct to sense humidity and temperature.

IMPORTANT

Select a location to expose sensor to average

duct humidity and temperature. Avoid locations

where stratification can cause sensing errors.

NOTES:

— H7635C is weatherproof for outdoor use.

Knockouts allow 1/2 in. conduit connection.

— To avoid damaging board during installation,

the cover can be detached completely:

1.Carefully remove wire plug from board.

2.Set the cover aside.

1. Cut a hole in the duct just large enough to accept

the sensing element.

2. Open case by rotating the cover counterclockwise.

3. Mount standard 1/2 in. conduit to the case.

4. Use case to mark mounting screw pilot hole

locations.

5. Drill the pilot holes and fasten the sensor to the

duct.

6. Wire the sensor. See Wiring section.

NOTE: The two free wires are thermistor wiring

connections. When connecting these, use

two wire nuts.

7. Reattach the wire plug and cover being careful not

to pinch wires between the cover and case.

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

63-2579—3 2

Outdoor Mounting

The H7635C senses outdoor air humidity and

temperature. Mount this control where it can sense

average outdoor air humidity and temperature. Normally,

the north side of a building provides a suitable location.

NOTES:

— H7635C is weatherproof for outdoor use.

Knockouts allow 1/2 in. conduit connection.

— To avoid damaging board during installation,

the cover can be detached completely:

1.Carefully remove wire plug from board.

2.Set the cover aside.

1. Open case by rotating the cover counterclockwise.

NOTE: Orient case so the element points down.

2. Mount standard 1/2 in. conduit to the case.

3. Use case to mark mounting screw pilot hole

locations.

4. Drill pilot holes.

5. Fasten the case to the wall.

6. Wire the sensor. See Wiring section.

NOTE: The two free wires are thermistor wiring

connections. When connecting these, use

two wire nuts.

7. Reattach the wire plug and cover being careful not

to pinch wires between the cover and case.

Output Settings (Table 1)

The board has three switch blocks:

— A six DIP switch block.

— A four DIP switch block.

— A white gang switch on a blue block.

1. Adjust the 4-switch block according to Table 1.

NOTE: The 6-switch block normally requires no

adjustment. (See the Appendix.)

2. Set the gang switch (white switch in blue block) to

correspond with the output (mA or Vdc).

NOTE: See Fig. 1 for DIP switch locations.

Table 1. Controller Compatibility

and Output Settings.

Fig. 1. DIP switch locations and settings.

Controller

Required

Sensor

Output

Setting

4-Switch Block

Settings

Blue and

White

Output

Switch

LONSPEC™

Setting4321

W7750, W7760,

W7761

4-20 mA — On — — 4-20 mA C7600C

W7750B,C

W7760C,

W7753, W7760

0-10 Vdc

(default)

On — — On Vout H7621/31

T7350, XL50,

XL100,

XL500 XF

Modules, XFL

0-10 Vdc

(default)

On — — On Vout n/a

Non-Honeywell 0-5 Vdc On — On — Vout n/a

M22705

NORMAL OPERATION

OFF

ON 0-10 VDC

OFF

ON 4-20 MA

0-5 VDC

OFF

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

3 63-2579—3

WIRING

For voltage output, shielded cable (16-22 AWG) should

be used.

For current output, either shielded cable or twisted pair

(16-22 AWG) can be used.

NOTE: When using shielded cable, ground the shield

only at the controller end (see Fig. 2). Grounding

both ends can cause a ground loop.

The 20K ohm NTC temperature output is accessed

through the separate blue and green wires (located inside

the enclosure).

Fig. 2. Typical wiring diagram for transducer with two-

wire mA output and external DC power supply.

Fig. 3. Humidity sensor (0-10 Vdc output) wiring with T7350

(use with RH/Temperature combination T7350 units only).

mA OUTPUT

TRANSDUCER

ONLY

18 TO 36 Vdc

POWER SUPPLY

CONTROLLER, METER

OR RECORDER

INPUT SIGNAL

COMMON

Vin +

Io –

–

M22528

GROUND

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

ENSURE TRANSFORMER IS SIZED TO HANDLE THE LOAD.

HEAT/COOL SYSTEMS WITH ONE TRANSFORMER REQUIRE THE FACTORY-INSTALLED JUMPER.

USE ECONOMIZER INSTRUCTIONS FOR INSTALLATION DIRECTIONS.

HC AND HP PROVIDE 24 VAC TO THE HUMIDITY SENSOR.

M22529

RCX

T7350

SUBBASE

W1 G

T7770 REMOTE SENSOR

W3/Y4 Y3 W2 Y2

AUXRH

T5 T6 T7 T4 T3

DISCHARGE

AIR

SENSOR

OUTDOOR

AIR

SENSOR

MOTION

SENSOR

HUMIDITY SENSOR

OSOS ASAS

MHC HP

Gnd Vin

(Vac)

(0-10 Vdc)

(HOT)

COMPRESSOR

CONTACTOR 1

COMPRESSOR

CONTACTOR 2

HEAT

RELAY 1

123456789

FAN

RELAY

ECONOMIZER

HEAT

RELAY 2

COMPRESSOR

CONTACTOR 3

COMPRESSOR

CONTACTOR 4

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

63-2579—3 4

Fig. 4. Typical wiring diagram for 5-wire temperature/humidity sensor with Vdc output

(used with the XL15A controller).

GND

OUT

GND GND 24

VAC

COM

VAC

COM

VAC

OUT

COM

VDC

OUT

GND E-BUS E-BUS

ANALOG

OUT

17 18 19 20 21 22 23 24 25 26 27 28 29

(HOT)

31 32 33 34 35 36 37 38 39 40 41 42 43 44

12345 678 9101112 14 1615

W7760A AI

GND

–

P7640

–

P7640

–

H76XX

–

M18302B

Vin (Vac)

Gnd

Vo (0-10 Vdc)

PWR

COM

OUT

PWR

COM

OUT

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

TEMPERATURE SIGNAL CONNECTIONS ARE NOT POLARITY SENSITIVE.

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

5 63-2579—3

CHECKOUT

CAUTION

Equipment Damage Hazard.

Can short electric circuitry.

• Never connect 120 Vac to the transducer.

• Connect only DC voltage to a transducer

intended for DC supply.

NOTE: Use laboratory quality meters and gauges for

applications requiring a high degree of accuracy.

1. Verify the transducer is mounted in the correct posi-

tion.

2. Verify appropriate input signal and voltage supply.

3. Verify appropriate configuration range.

Converting Output Signal to Percent RH

4 to 20mA Signal

Example: 12 mA output signal

(12 - 4)/ 0.16 = 50% RH

0 to 10 Vdc Signal

Example: 8 VDC transmitter signal output

8 Vdc/0.10 = 80% RH

Table 2. Troubleshooting.

signal [in mA] 4–〈〉

0.16

------------------------------------------------- p e r c e n t R H=

Problem Items to Check

No reading •Verify correct supply voltage at the power terminal blocks.

•Verify correct wiring configuration and DIP switch settings.

•Verify that terminal screws are connected tightly with all wires firmly in place.

Erratic readings •Verify all wires are terminated properly.

•Ensure that there is no condensation on the board.

•Verify clean input power. In areas of high RF interference or noise, shielded cable can be

necessary to stabilize signal.

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

63-2579—3 6

APPENDIX

RH Test and Configuration DIP Switch Settings (Table 3)

IMPORTANT

• Only adjust these switches for troubleshooting or

recalibrating the sensor. (Adjustment is not

normally necessary.)

• For normal operation, always keep DIP switch 3

in the ON position. When DIP switch 3 is off, the

RH transmitter cannot read the sensor. This

inability-to-read forces the output to never

change.

Table 3. Test/Calibration Settings (Six-Switch Block).

0% RH Output (for Testing Only)

Transmitter always outputs a signal of 4 mA or 0 Vdc. The

sensor does not affect the transmitter output.

50% RH Output (for Testing Only)

Transmitter always outputs a signal of 12 mA, 2.5 VDC, or

5 VDC. The sensor does not affect transmitter output.

100% RH Output

Transmitter always outputs a signal of 20 mA, 5 VDC, or

10 VDC. The sensor does not affect the transmitter

output. Sensor doesn’t affect the transmitter output.

Normal Operating Condition

DIP switch 3 must be set in the On position for normal

operation. All other DIP switches must be set Off.

Setting 654321

Normal Operation (Default) — — — On — —

0%RHOutput On—————

50%RHOutput —On————

100% RH Output — — On — — —

Increment RH Output — — — — On —

DecrementRHOutput —————On

Reset to Original Calibration — — — — On On

H7625B; H7635B,C; H7655B DUCT-MOUNT AND OUTDOOR-MOUNT HUMIDITY/TEMPERATURE SENSORS

7 63-2579—3

CALIBRATION

All transducers are factory calibrated to meet/exceed published

specifications. Field adjustment should not be necessary.

IMPORTANT

• Do not verify comparative RH with a sling

psychrometer. Too many variables exist which

induce errors into this process.

• Recalibration must be done in a controlled

environment. Relative humidity must be held

stable while making any adjustment.

• Verify the device output directly with calibrated

instrumentation and verify RH with calibrated

instrumentation. Never use a controller output.

• With correct power applied, and only a meter

connected to the transducer output, ensure that

the output is proportional to the true RH.

Using Increment/Decrement Switches

Increment RH Output

This DIP switch allows you to calibrate the sensor through

the software. The switch must be toggled from the Off to

the On position and then returned to the Off position for

an increase of 0.5% RH. This means that if your humidity

has drifted 1% lower over a certain time period, you can

toggle the Increment RH Output switch (2 times) in order

to slide the whole curve upward 1%.

Decrement RH Output

This DIP switch allows calibration in the same way as the

Increment RH. The difference is that each toggle results

in a decrease of 0.5% RH.

Using Calibration Trim Potentiometers

IMPORTANT

• Due to sensitive nature of humidity calibration,

adjusting trimmer potentiometers is not highly

recommended.

• Calibrate only in a stable humidity/temperature

chamber of laboratory grade.

Single Point Calibration

IMPORTANT

Use only one of the following two options.

OPTION 1

1. Select a controlled humidity environment between

10 and 40 percent RH. Be sure humidity is stable.

2. Adjust zero trimmer (z).

OPTION 2

1. Select a controlled humidity environment between

40 and 70 percent RH. Be sure humidity is stable.

2. Adjust span trimmer (s).

Two Point Calibration

1. Select a controlled humidity environment between

10 and 40 percent RH. Be sure humidity is stable.

2. Adjust zero trimmer (z).

3. Select a controlled humidity environment between

70 and 75 percent RH. Be sure humidity is stable.

4. Adjust span trimmer (s).

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9

customer.honeywell.com

® U.S. Registered Trademark

63-2579—3 B.B. Rev. 01-05

LonSpec™ is a trademark of Echelon®Corporation.

Ce manuel convient aux modèles suivants

Autres manuels Honeywell Régulateurs de température

Honeywell

Honeywell C7650A Manuel utilisateur

Honeywell

Honeywell NOTIFIER FST-951-SELFT Manuel utilisateur

Honeywell

Honeywell PRO 2000 Series Manuel utilisateur

Honeywell

Honeywell T775A Manuel d'utilisation

Honeywell

Honeywell T991A Manuel utilisateur

Honeywell

Honeywell MICRONIK 200 R7426A Manuel d'installation

Honeywell

Honeywell DC1010 Manuel utilisateur

Honeywell

Honeywell EVOTOUCH CONTROLLER Manuel utilisateur

Honeywell

Honeywell ASC02-01WM Manuel utilisateur

Honeywell

Honeywell Pegasus 190937-ZBC Manuel utilisateur

Honeywell

Honeywell FIRE-LITE ALARMS W-H355 Manuel utilisateur

Honeywell

Honeywell R7426A Manuel utilisateur

Honeywell

Honeywell TS13F Manuel utilisateur

Honeywell

Honeywell T7022A Manuel utilisateur

Honeywell

Honeywell TS33F Manuel utilisateur

Honeywell

Honeywell SDC heating and district heating controller Manuel utilisateur

Honeywell

Honeywell TS03 Manuel utilisateur

Honeywell

Honeywell 121371B Manuel d'utilisation

Honeywell

Honeywell MICRONIK 200 R7426A Manuel d'installation

Honeywell

Honeywell HR92 Manuel utilisateur

Honeywell

Honeywell IPC500 Manuel utilisateur

Honeywell

Honeywell ST9400S Manuel utilisateur

Honeywell

Honeywell T7560A Manuel utilisateur

Honeywell

Honeywell PRO 2000 Series Manuel d'utilisation

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage