Honeywell Searchline Excel Cross-Duct Note de version

Searchline Excel Cross-Duct

Infrared Gas Detector

Technical Handbook

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Ensure that you read and understand these instructions BEFORE operating the equipment.

Please pay particular attention to the Safety Warnings.

WARNINGS

1. TheSearchlineExcelgasdetectoriscertiedforandintendedforuseinpotentiallyhazardousareas.

Install and use the Searchline Excel gas detector in accordance with the latest regulations.

2. For installations in Europe, the Code of Practice SELECTION, INSTALLATION AND

MAINTENANCE OF ELECTRICAL APPARATUS FOR USE IN POTENTIALLY EXPLOSIVE

ATMOSPHERES should be strictly observed. General recommendations are given in

EN 60079-14:2008 & IEC 60079-14:2007. Refer to EN 60079-29-2:2007 & IEC 60079-29-

2:2007 in Europe or the appropriate local or national regulations.

3. For installations in North America, the national Electrical Code (NFPA 70 - 1990) or later issues

should be strictly observed.

4. Elsewhere, the appropriate local or national regulations should be used.

5. The Searchline Excel gas detector must be properly earthed to protect against electrical shock

and minimise electrical interference. For electrical installation design considerations refer to

Section 3.

6. Operators must be fully aware of the action to be taken if the gas concentration exceeds an

alarm level.

7. Dismantling or repair of equipment should be carried out in the safe area only.

8. Test gases may be toxic and/or combustible. Refer to Material Safety Sheets for

appropriate warnings.

9. Do not drill holes in any housing as this will invalidate the explosion protection.

10. In order to maintain electrical safety, the unit must not be operated in atmospheres with more

than 21% oxygen.

11. Ensurethattheboltswhichsecureameproofenclosuresarefullytightened.Thesecuring

boltsusedaremadefromaspecialcertiedgradeofsteel.OnlyboltssuppliedbyHoneywell

Analyticsshouldbettedforthispurpose.

12. Do not open the enclosure in the presence of an explosive atmosphere.

13. The transmitter unit contains high voltages when operational. These are discharged when the

unit is removed from its enclosure.

14. TheconduitandcableglandsttedtoSearchlineExcelshouldnotbemodied.If,however,it

becomesnecessarytomakemodicationstheymustcomplywiththerelevantnationalCodes

of Practice.

15. The optical energy emitted by the Searchline Excel is less than 20mW/mm2.

16. Searchline Excel Cross-Duct should only be used to detect gas mixtures where methane is the

main constituent (>70%) and the balance is C2- C6hydrocarbons.

Safety

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Cautions

1. Use only approved parts and accessories with the Searchline Excel gas detector.

2. To maintain safety standards, commissioning and regular maintenance of the Searchline Excel gas detector

shouldonlybeperformedbyqualiedpersonnel.

Important Notices

1. HoneywellAnalyticscantakenoresponsibilityforinstallationand/oruseofitsequipmentifthisisnotdonein

accordance with the appropriate issue and/or amendment of the manual.

2. The user of this manual should ensure that it is appropriate in all details to the exact equipment to be installed

and/oroperated.Ifindoubt,theusershouldcontactHoneywellAnalyticsforadvice.

3. Effect of explosive atmosphere on materials.

Searchline Excel is made from materials which exhibit good resistance to corrosive and solvative substances.

The Exd enclosures are made from 316 stainless steel and the explosion protected windows are made from

toughenedsodalimeglass.HoneywellAnalyticsarenotawareofanysignicanteffectsofexplosiveatmospheres

uponthesematerials.ContactHoneywellAnalyticsoroneoftheiragentsforspecicqueries.

Special Conditions of Use

InordertocomplywiththeATEX/IECExCertication,thefollowingspecialconditionsofusemustbeadheredto:-

1. The integral supply cables must be mechanically protected and terminated in a suitable terminal or junction

facility.

2. Thecoverxingscrewsshallbestainlesssteelgrade12.9minimum,gradeA2-80orgradeA4-80(only

useHoneywellsuppliedscrews)

Everyefforthasbeenmadetoensuretheaccuracyofthisdocument,however,HoneywellAnalyticscanassume

no responsibility for any errors or omissions in this document or their consequences.

HoneywellAnalyticswouldgreatlyappreciatebeinginformedofanyerrorsoromissionsthatmaybefoundin

the content of this document.

For information not covered in this document, or if there is a requirement to send comments/corrections about

thisdocument,pleasecontactHoneywellAnalyticsusingthecontactdetailsgivenonthebackpage.

HoneywellAnalyticsreservetherighttochangeorrevisetheinformationsuppliedinthisdocumentwithout

notice and without obligation to notify any person or organisation of such revision or change. If information

isrequiredthatdoesnotappearinthisdocument,contactthelocaldistributor/agentorHoneywellAnalytics.

Safety

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Section Page

1. Introduction 7

2. Overview 9

2.2 Transmitter and Receiver Unit 10

2.2.1 Transmitter 10

2.2.2 Receiver 10

2.2.3 Mounting Block 11

 2.3 HeatedReectorPanel 11

3. Installation and Operation 12

3.1 Introduction 12

3.2 Siting and Mounting 12

3.2.1 General 12

3.2.2 Location for Best Coverage 12

3.2.3 Location to Maximise Reliability and Availability 12

3.2.4 Beam Path 13

3.2.5 Orientation 13

3.2.6 Access for Cleaning 14

3.3 Electrical Connections 14

3.3.1 General 14

3.3.2 Transmitter and Receiver Connections via DVC100 (M) MK2 15

3.3.3 Transmitter and Receiver Connections via DX100 (M) 15

3.3.4 Transmitter and Receiver Connections 16

3.3.5 Remote Installations 17

3.4 Power Supply 17

3.4.1 General 17

3.4.1.1 Transmitter and Receiver Unit 17

   3.4.1.2HeatedReectorPanel 17

3.4.2 Power Supply Connections - Turbo heating Disabled 19

3.5 Installation Procedure 20

3.5.1 General 20

3.5.2 Mechanical Installation 20

3.5.2.1 Transmitter and Receiver Unit 20

3.5.2.2HeatedReectorPanel 21

Contents

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Section Page

3.5.3 Electrical Installation 22

3.6 Commissioning 22

3.6.1 General 22

3.6.2 Connecting the Interrogator 22

3.6.3 Power Up 24

3.6.4 Setting the Real-Time Clock 25

3.6.5 Initialising the Searchline Excel Cross-Duct Gas Detector 26

3.6.6 Functional check 28

3.6.7 Finish 28

3.7 System Controller Calibration 29

3.8 Installation Checks/ Tests 30

4. Maintenance 35

4.1 Inspection and Cleaning 35

 4.2 Re-zero  36

4.3 Functional Checking 36

4.3.1 Functional Checking with Gassing Cell (Short Range versions only) 36

4.3.2 Functional Checking with Test Filters 37

5. Problem Solving 38

6. Specications  42

6.1 System 42

7. Certication  43

7.1 General 43

7.2 Conduit Technical Characteristics (ATEX, IECEx version) 44

 7.3 CerticationLabelsATEX,IECEx 44

7.3.1 Transmitter 44

7.3.2 Receiver 45

  7.3.3HeatedReectorPanel 46

7.3.4 System Diagram 47

 7.4CerticationlabelsUL 48

7.4.1 Transmitter 48

Contents

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Section Page

7.4.2 Receiver 49

  7.4.3HeatedReectorPanel 50

7.4.4 System Diagram With DX100M Termination Unit 51

8. Warranty Summary 52

AppendixA-HandheldInterrogator 53

A.1 Introduction 53

A.2 Overview 53

A.3 Connection to System 54

A.4 Basic User Tasks 55

A.5 Menus 56

A.5.1 Main Menu 57

A.5.2 Display Menu 57

A.5.3 Calibrate Menu 58

A.5.4 Diagnose Menu 63

  A.5.5CongMenu 65

A.5.6 Chg Mode 67

A.5.7 Power Off 67

A.6 PROBLEM SOLVING 67

Appendix B - Glossary 68

B.1 Terminology 68

B.2 Open Path Detector Measurement Units 69

B.3 Abbreviations 69

Appendix C - Accessories & Spare Parts 70

C.1 System Units 70

C.2 General 70

Contents

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

The Searchline Excel Cross-Duct Gas Detector is an open path infrared gas detector for methane.

It will detect hydrocarbon gas mixtures where methane is the main constituent (>70% of the composition with

the balance being C2- C6hydrocarbons).ForothergasmixturespleasecontactHoneywellAnalyticsforadvice.

Searchline Excel Cross-Duct is specically designed for use where the path length is between 0.5 and 5

metres for applications such as air intake ducts. It consists of a Transmitter and Receiver unit, and a separate

HeatedReectorPanel.

The detector operates on the principle of infrared (IR) absorption. If a cloud of methane gas is present, part

of the infrared light is absorbed by the gas, causing a reduction in the signal received that is proportional to

the amount of gas in the beam.

The detector output signal is proportional to 0-100%LEL (Lower Explosive Limit) of gas.

Searchline Excel Cross-Duct is suitable for use in Zone 1 or 2 hazardous areas (International) and for

Class 1 Division 1 or 2 area applications (North America).

Note: THE INFRARED BEAM IS INVISIBLE AND EYE SAFE.

Thishandbookconsistsofthefollowingparts:

• Chapter 1 Introduction

• Chapter 2 Overview

A brief description of the system components

• Chapter 3 Installation and Operation

Important information regarding detector positioning, electrical

connections, power supply requirements, mechanical installation and

commissioning, including an installation check list

• Chapter 4 Maintenance

Regular maintenance requirements and instructions for functional

checks

• Chapter 5 Problem Solving

 • Chapter6 Specications

 • Chapter7 Certication

• Appendix A Handheld Interrogator

• Appendix B Glossary

• Appendix C Accessories & Spare Parts

1. Introduction

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

Information notices

Thetypesofinformationnoticesusedthroughoutthishandbookareasfollows:

Caution: Indicates hazardous or unsafe practice which could result in minor injury to personnel, or

product or property damage.

Note: Provides useful/helpful/additional information.

If more information beyond the scope of this technical handbook is required please contact

HoneywellAnalytics.

Associated Documents

DX100SeriesTerminationUnitsTechnicalHandbook PartNo:2104M0701

DVC100(M)MK2TerminationUnitQuickStartGuide PartNo:2104M0409

WARNING

Indicates hazardous or unsafe practice that could result in severe injury

or death to personnel.

1. Introduction

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

2.1 Introduction

SearchlineExcelCross-DuctgasdetectorconsistsofaTransmitterandReceiverunit,andaHeatedReector

Panel.TheTransmitterandReceiverunitgeneratesanddetectstheinfraredbeam.TheHeatedReectorPanel

ismountedattheoppositesideoftheducttoreectthebeamfromtheTransmitterbacktotheReceiver.

Note: THE INFRARED BEAM IS INVISIBLE AND EYE SAFE.

TherearetworangesofSearchlineExcelCross-Ductgasdetector.Theseare:

Version Path Length (m) Path Length (ft) Certication

Short Range: 0.5 — 2.5m (20in — 8ft) ATEX, IECEx, UL

Long Range: 2.5 — 5m (8ft — 15ft) ATEX, IECEx

ThelongrangegasdetectorusesalargerReectorPanelthantheshortrangeversion.

2. Overview

Heated Reflector Panel

Mounting Plate

Mounting Block

Transmitter

Conduit

Receiver

Junction Box

(type DVC100 (M) MK2)

MAN0889_Issue 3_03/13 Searchline Excel Cross-Duct Technical Handbook

2.2 Transmitter and Receiver Unit

2.2.1 Transmitter

TheTransmitterproducesanintense,collimatedinfraredbeamfromaXenonarcashlamp.TheTransmitter

window is heated to minimise condensation and frosting. During particularly cold operating conditions, the

heating of the Transmitter window is increased to turbo levels. The turbo mode can be disabled if not required.

ElectricalconnectionstotheTransmitteraremadeviawireswhichrunthroughtheprotective,exibleconduit.

There are three Transmitter wires, red (+24V), black (0V) and green/yellow (GND).

Note: The infrared beam is invisible and eye safe.

2.2.2 Receiver

The Receiver collects infrared radiation from the Transmitter and performs measurements to enable methane

gas in the beam path to be detected.

The Receiver output signal is 4 - 20mA available as a source or sink option. The output is calibrated for a

range of 0 to 100% LEL methane.

Note: The detector uses the duct width in the calculation of gas reading – it is essential that this is

specied correctly during installation (See Appendix B.2 for the explanation of how open path gas

detectors measure gas concentration)

Output signal levels below 4mA are used to indicate Fault (0mA), Inhibit (2mA), Beam Blocked (2.5mA) and

Low Signal (3mA).

TheReceivercommunicateswiththeSHC1HandheldInterrogatorusinganRS485output.TheSHC1isused

to perform commissioning, functional testing and diagnostic procedures.

The Receiver window is heated to minimise condensation and frosting.

ElectricalconnectionstotheReceiveraremadeviawireswhichrunthroughtheprotectiveexibleconduit.

There are six Receiver wires, red (+24V), black (0V), white (4 - 20mA), orange (RS485 A), blue (RS485 B) and

green/yellow (GND).

2. Overview

Air Shield

Slot for test filter

Gas In/Out

Gassing Cell

Transmitter

Mounting Block

Beamsplitter

Receiver

Table des matières

Autres manuels Honeywell Capteur de sécurité

Honeywell

Honeywell NOTIFIER IRX-751CTEM Manuel utilisateur

Honeywell

Honeywell ESSER 784763 Manuel utilisateur

Honeywell

Honeywell SPM Flex Manuel utilisateur

Honeywell

Honeywell Lyric YCHW4000W4004 Guide d'installation

Honeywell

Honeywell W1KS Manuel utilisateur

Honeywell

Honeywell FlexGuard FG-1625SN V-Plex Manuel utilisateur

Honeywell

Honeywell Notifier FST-851 Series Manuel utilisateur

Honeywell

Honeywell Miller Twin Turbo G2 Connector Manuel de l'opérateur

Honeywell

Honeywell EC-P2 Manuel

Honeywell

Honeywell Ex-Or Digital Gold Series Manuel d'installation et d'exploitation

Honeywell

Honeywell Miller Falcon MP50G-LE Instructions d'installation

Honeywell

Honeywell Miller MightyLite Series Manuel utilisateur

Honeywell

Honeywell EC-FX-NH3 Manuel

Honeywell

Honeywell HAQSPA-R Manuel utilisateur

Honeywell

Honeywell FSL100-IR3 Note de version

Honeywell

Honeywell Peha D MLS2001AF Manuel d'installation et d'exploitation

Honeywell

Honeywell Ex-Or MR1500P Manuel d'installation et d'exploitation

Honeywell

Honeywell Ex-Or MLS2500CDR Manuel d'installation et d'exploitation

Honeywell

Honeywell FS20X Series Manuel utilisateur

Honeywell

Honeywell Miller 8172 Manuel de l'opérateur

Honeywell

Honeywell 5800CO Instructions de montage

Honeywell

Honeywell SiXCOMBO Manuel utilisateur

Honeywell

Honeywell LightSpot LS1000R Manuel utilisateur

Honeywell

Honeywell Connected Home DO8EZS Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur