Honeywell XENON 1902G-BF Manuel utilisateur

Xenon™ 1902G-BF

CCB01-010BT-BF

Battery-Free Wireless Area-Imaging Scanner and 

Charge Base

Quick Start Guide

Rev C

2/17

Note: Refer to your user’s guide for information about cleaning

your device.

Getting Started

Turn off the computer’s power before connecting the base, then

power up the computer once the base is fully connected. When

the base is connected and powered up, put the scanner in the

base to establish a link. The green LED on the base flashes to

indicate the scanner’s instant charge pack is charging. The

scanner must be returned to the base when not in use. A scan-

ner charged on the base with the power supply for 35 seconds

will result in 100 scans, with one scan every second.

Power Supply Assembly (if included)

Note: The power supply must be ordered separately, if needed.

Connecting the Scanner

USB:

Note: If you are charging the scanner using the USB cable, the

current available for charging is reduced and charge times

are increased. Charging via the power supply is faster.

Keyboard Wedge:

RS232 Serial Port:

RS485:

LED Sequences and Meaning

When charging, the base indicates the progress while the scan-

ner resides in the base.

Base Button/LED Charge Level Approximate

Expected Scans*

Green on 100% 450

Green slow blink 50-99% 200

Green fast blink 30-50% 100

Yellow fast blink 0-30% Charging - do not

scan

The following feedback is provided by the scanner when the

scanner is out of the base and has been idle for 5 seconds.

* The number of scans was measured with a clearly printed UPC code in

good light. The approximate number of scans varies with changes in

label quality, symbology, and environmental factors.

Reading Techniques

The view finder projects an aim-

ing beam that should be centered

over the bar code, but it can be

positioned in any direction for a

good read.

Hold the scanner over the bar

code, pull the trigger, and center

the aiming beam on the bar code.

The aiming beam is smaller when

the scanner is closer to the code

and larger when it is farther from the code. Hold the scanner

close to smaller bar codes, and farther away from large bar

codes to get a proper read.

Scanner LED Scanner Beep Charge

Level

Approximate

Expected

Scans*

Yellow 

3 sets of flashes

2 short beeps per

flash

30% 100

Red 

3 sets of flashes

2 short beeps per

flash

10% 50

If the bar code is highly reflective (e.g., laminated), you may need

to tilt the scanner at an angle so the bar code can be scanned.

Note: If the scanner beeps 3 times when scanning a bar code, the

link has not been established. If the scanner beeps once,

the link has been established.

Standard Product Defaults

The following bar code resets all standard product default set-

tings.

RS485 Interface

The RS485 interface defaults to port 5B. If you have an IBM POS

terminal using port 9B, scan the appropriate code below to pro-

gram the terminal, then power cycle the cash register.

Note: For additional RS485 interface selections, see the User’s

Guide for your product at our website,

www.honeywellaidc.com.

Standard Product

IBM Port 9B HHBCR-1

Interface

IBM Port 9B HHBCR-2

Interface

USB Serial

Scan the following code to program the scanner to emulate a

regular RS232-based COM Port. If you are using a Microsoft®

Windows® PC, you will need to download a driver from the Hon-

eywell website (www.honeywellaidc.com). The driver will use the

next available COM Port number. Apple® Macintosh computers

recognize the scanner as a USB CDC class device and automati-

cally use a class driver.

Note: No extra configuration (e.g., baud rate) is necessary.

USB PC Keyboard

Scan the following code to program the scanner for a USB PC

Keyboard.

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan

the numeric bar code(s) from page 2, then the Save bar code to

program the keyboard for your country. As a general rule, the

following characters are not supported by the scanner for coun-

tries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

USB Serial

USB PC Keyboard

Program Keyboard Country

Note: For a complete list of country codes, see the User’s Guide

for your product at our website, www.honeywellaidc.com.

Locked Link

If you link a scanner to a base using the Locked Link Mode,

other scanners are blocked from being linked if they are inad-

vertently placed into the base. If you do place a different scan-

ner into the base, it will charge the scanner, but the scanner will

not be linked.

Country Code Scan Country Code Scan

Arabia 91 Korea 93

Belgium 1 Portugal 13

China 92 Russia 26

France 3 Spain 10

Germany/Austria 4 Sweden/Finland 2

Great Britain 7 Switzerland 6

Hungary 19 Thailand 94

IBM Financial 90 Turkey (Q) 24

Italy 5 USA (Default) 0

Japan 28 Vietnam 95

Save

Locked Link Mode

(Single Scanner)

To use a different scanner, you need to unlink the original scan-

ner by scanning the Unlink Scanner bar code.

Override Locked Scanner

If you need to replace a broken or lost scanner that is linked to a

base, scan the Override Locked Scanner bar code with a new

scanner, and place that scanner in the base. The locked link will

be overridden; the broken or lost scanner’s link with the base will

be removed, and the new scanner will be linked.

Unlinking the Scanner

If the base has a scanner linked to it, that scanner must be

unlinked before a new scanner can be linked. Once the previous

scanner is unlinked, it will no longer communicate with the

base. Scan the Unlink Scanner bar code to unlink a scanner.

Override Locked Scanner

Unlink Scanner

Autres manuels pour XENON 1902G-BF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Honeywell Scanner

Honeywell

Honeywell 8670 Manuel utilisateur

Honeywell

Honeywell 4022 Guide de l'utilisateur

Honeywell

Honeywell N3680 Manuel utilisateur

Honeywell

Honeywell 6300dpm Manuel utilisateur

Honeywell

Honeywell 8680i Series Manuel utilisateur

Honeywell

Honeywell SF61 Manuel utilisateur

Honeywell

Honeywell Xenon 1902HC Manuel utilisateur

Honeywell

Honeywell VOYAGER 1250G Manuel utilisateur

Honeywell

Honeywell QuantumT MS3580 Manuel utilisateur

Honeywell

Honeywell Voyager XP 1472g Series Manuel utilisateur

Honeywell

Honeywell XENON 1900 Manuel utilisateur

Honeywell

Honeywell 4800dr - Document Camera Manuel utilisateur

Honeywell

Honeywell Voyager 1450g Series Manuel utilisateur

Honeywell

Honeywell HH400 Manuel utilisateur

Honeywell

Honeywell 3900 Manuel utilisateur

Honeywell

Honeywell HF680 Manuel utilisateur

Honeywell

Honeywell Voyager 1602g Manuel utilisateur

Honeywell

Honeywell YOUJIE YJ-HH360 Manuel utilisateur

Honeywell

Honeywell Xenon 1902h Manuel utilisateur

Honeywell

Honeywell Eclipse 90 Manuel utilisateur

Honeywell

Honeywell Xenon XP 1952g Manuel utilisateur

Honeywell

Honeywell Granit 1280i Manuel utilisateur

Honeywell

Honeywell Vuquest 3330g Manuel utilisateur

Honeywell

Honeywell XENON 1900 Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Fujitsu

Fujitsu CardMinder Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur