Honeywell VERSAFLOW VORTEX 200 Manuel utilisateur

Quick Start

For initial set up, we strongly recommend the use of the relevant manuals in addition!

07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 1

VERSAFLOW VORTEX 200

Vortex flowmeter

Installation, assembly, start-up and maintenance may only be performed by appropriately

trained personnel.

For use in hazardous areas, special codes and regulations are applicable which are supplied in

a separate document that describes all hazardous area relevant information.

The responsibility as to the suitability, intended use and corrosion resistance of the used

materials against the measured fluid of this device rests solely with the operator.

For complete documentation (manuals, supplementary manuals, data sheets and certificates)

please refer to www.honeywellprocess.com.

1 Installation

Liquids

Steam & gases

Sandwich design – centering rings

Centering rings

(part of scope of supply)

Transport

Pipelines with control valve

Remote: wall mounting of the field housing Remote: pipe mounting of the field housing



5 DN

07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 2

2 Electrical connection

Minimum inlet section



15 DN

 50 DN



20 DN

 20 DN

 40 DN



30 DN

> 5 DN



5 DN



5 DN

Minimum outlet section Heat insulation for Tmedium > +160°C / +320°F

1 1

1 Marking of max. height of the insulation

2 Max. thickness of the insulation up to the bend of the pressure pipe

3 Insulation

1 Open the housing cover of the electrical terminal compartment using the key

2 Signal converter supply and 4...20 mA loop

3 4...20 mA current input, - external transmitter, optional

4 Terminal M1 binary (high current)

5 Terminal M3 binary (NAMUR)

6 Terminal M2/4 binary, common minus connection

7 Ground terminal in housing

8 Ground terminal on connection piece between flow sensor and signal converter

Connecting the signal converter

Sunshade

07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 3

Terminal Strand colour

rd red

bu blue

bk black

gr grey

ye yellow

gn green

gnye Shielding

Current output

Current input

Pulse output / frequency output

Limit switch output

Power supply for the signal

converter

Current input (I1+ and I2-) of an external

temperature or pressure transmitter

Connect current loop 4..20 mA to

terminals C1+ and C2-

Connection NAMUR:

M2/4 (common); M3 (open collector)

Connection transistor output:

M2/4 (common); M1 (open collector)

The maximum frequency of both pulse

output and frequency output is 1000 Hz

The connection is made between terminal

M2/4 Common (-) and M1 for Hi Current

(+) or M3 NAMUR (+)

Status output

The connection is made between terminal M2/4 Common (-) and M1 for Hi Current (+) or

M3 NAMUR (+)

Connection of remote version

1 Connection terminal flow sensor

2 Connection terminal signal converter

3 Connection shielding flow sensor

4 Shielding (drain wire and overall shield)

5 Connection shielding signal converter

6 Heat shrink tubing

7 Shielding

1 2

7 7

Grounding of compact version

1 Ground terminal in housing

2 Ground terminal on connection piece between

flow sensor and signal converter

Grounding of remote version

1 Ground terminal on flow sensor

2 Ground terminal on signal converter housing

07/2019 - 4007779101 - 34-VF-25-76 iss.1 GLO July 2019 US 4

3 Quick Setup

Meas. Menu A Submenus



 >



 >





A Quick

Setup

A1 Language

A2 Contrast

A3 Login

A4 Tag

A5 Long Tag

A6 Message View

A7 Fluid

A8 Medium

A9 Units

A9.1 Volume Flow A9.2 Cst. Vol. Flow

A9.3 Norm. Vol. Flow A9.4 Cst. N.Vol.Flow

A9.5 Mass Flow A9.6 Cst. Mass Flow

A9.7 Power A9.8 Cst. Power

A9.9 Volume A9.10 Cst. Volume

A9.11 Norm. Volume A9.12 Cst. Norm. Volume

A9.13 Mass A9.14 Cst. Mass

A9.15 Energy A9.16 Cst. Energy

A9.17 Pressure A9.18 Cst. Pressure

A9.19 Temperature A9.20 Cst. Temp.

A9.21 Density A9.22 Cst. Density

A10 Meter Type

A11 Application Assistant

A11.1 Liquids

A11.2 Saturated Steam

A11.3 Superheated Steam

A11.4 Heat Measurement

A11.5 Gas

A11.6 FAD

A12 Cluster Checks Cluster 1...12

Access level Def ault p a ssword Permis sions

User 0000

(any unassigned password)

 View device information

 Configure the display (C5), including changing the display

language and the content of the measurement pages

Operator 0009  All rights of "User" access level

 Configure binary output (C2.2)

 Configure all HART® communication options (C3) with the

exception of "C3.1.1 Current Loop Mode"

 Change "Operator" password (C6.2.2) – note that the new

password must have three leading zeroes ("000")

 Activate a different meter type

Expert 0058  All configuration rights, especially process setup (C1) and

current output (C2.1)

 Change "Expert" password (C6.2.2) – note that the new

password must have two leading zeroes ("00")

Contact

Honeywell Process Solutions

1250 W Sam Houston Pkwy S

Houston, TX 77042

www.honeywellprocess.com

Subject to change without notice.

Operation with open front cover Operation with

closed

front cover

(with bar magnet)

Autres manuels pour VERSAFLOW VORTEX 200

Table des matières

Autres manuels Honeywell Instrument de mesure

Honeywell

Honeywell OELD Manuel utilisateur

Honeywell

Honeywell A700 Manuel utilisateur

Honeywell

Honeywell QX Manuel utilisateur

Honeywell

Honeywell COCON 26 DRA-LP/MP Manuel utilisateur

Honeywell

Honeywell TS34C Manuel utilisateur

Honeywell

Honeywell DPR180 Manuel utilisateur

Honeywell

Honeywell Sensepoint XCL Manuel utilisateur

Honeywell

Honeywell HTRAM-V1-W Manuel utilisateur

Honeywell

Honeywell SmartLine RMA801 Manuel utilisateur

Honeywell

Honeywell AirAlert 96d Manuel

Honeywell

Honeywell W8710A Manuel utilisateur

Honeywell

Honeywell BendixKing KLR 10 Manuel utilisateur

Honeywell

Honeywell DR 4300 Mode d’emploi

Honeywell

Honeywell Bendix/King KN 63 Manuel utilisateur

Honeywell

Honeywell Q4000 Manuel utilisateur

Honeywell

Honeywell AD1200-CT Manuel utilisateur

Honeywell

Honeywell HAQ Series Guide d'installation

Honeywell

Honeywell 90DM4 Manuel utilisateur

Honeywell

Honeywell HERMetic UTImeter Gtex Chem IIC Manuel d'utilisation

Honeywell

Honeywell DVC100 (M) MK2 Manuel utilisateur

Honeywell

Honeywell Enraf 977 Manuel utilisateur

Honeywell

Honeywell UDA2182 Guide d'installation

Honeywell

Honeywell RABO Manuel utilisateur

Honeywell

Honeywell BW RigRat Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur