Honeywell DR 4300 Mode d’emploi

Form 43-DR-33-74 Page 1 of 3

Model DR 4300

Circular Chart Recorder

Replacement Instruction

Display Module Printed Circuit Assembly (51404459-501)

Document Number Form: 43-DR-33-74

Effective: 3/98

Supersedes: None

Kit Contents This Display Module Printed Circuit Assembly (PCA) Kit contains the

following parts:

•Display PCA

•#6 x 3/8 Plastite Screws (2)

•Cables (2)

Summary Enclosed are a new display module PCA and parts for your DR4300

recorder. Use the following procedure to install the new display module.

WARNING Never access components inside the case with power applied.

Continued next page

Kit Instruction, continued

Page 2 of 3 Form 43-DR-33-74

Component Location Refer to Figure 1 for the component locations and Table 1 for the

installation procedure.

24229

Screws

Display

ModulePCA

Cable

Pen 2

Cable

Pen 1

Figure 1 – Component Location

Kit Instruction, continued

Form 44-DR-33-74 Page 3 of 3

Installation Procedure Follow the procedure in Table 1 to install the new display module PCA in

your recorder.

Table 1 – Display Module Printed Circuit Assembly Installation

Step Action

1Power down the recorder. Open the chart door and swing the chart

plate out.

2 Note cable orientation before removing the two screws holding the

display module PCA to the top of the case.

3 Disconnect cable(s) from the back side of old PCA. Pull outward

on the connector’s end tabs then pull out the ribbon cable(s).

You can leave the cable(s) attached to J4 on the main PCA(s)

unless you are also replacing the cable. If you are replacing the

cable(s), disconnect each one from J4 on its specific PCA and

remove it, noting the routing layout.

4 Install the cable(s) on the new display PCA. Insert the cable in the

connector and push in on end of connector tabs to lock cable(s) in

place.

If you are replacing the cable(s), go to Step 5.

If you are using the existing cable(s), go to Step 6.

5 Feed the pen 1 ribbon cable behind the transmitter power

assembly, behind the Main PCA for pen 1 (right side of case) to its

J4 connector (upper right corner).

If applicable, run the pen 2 ribbon cable behind the transmitter

power assembly, behind the pen 1 Main PCA, bringing it to the J4

connector on the Main PCA for pen 2 (left side of case). This

ribbon should be on top of the pen 1 ribbon cable.

6 Secure the new display PCA to the case with the screws provided.

7 Close the chart plate and apply power. Check for normal display

indication.

Table des matières

Autres manuels Honeywell Instrument de mesure

Honeywell

Honeywell AUTOCUBE 8200 Manuel utilisateur

Honeywell

Honeywell EWA600C-RF55C Manuel utilisateur

Honeywell

Honeywell eZtrend GR Series Manuel utilisateur

Honeywell

Honeywell RABO G65 Manuel utilisateur

Honeywell

Honeywell NK Manuel utilisateur

Honeywell

Honeywell Morley-IAS MI-IM10 Manuel utilisateur

Honeywell

Honeywell Envitec MySignO Manuel utilisateur

Honeywell

Honeywell VERSAFLOW MAG 200 Manuel utilisateur

Honeywell

Honeywell VERSAFLOW SONIC 2000 Supplément

Honeywell

Honeywell 6108 Comment utiliser

Honeywell

Honeywell FlexLine SmartServo 954 Manuel utilisateur

Honeywell

Honeywell BW RigRat Manuel utilisateur

Honeywell

Honeywell RMA300-ME Manuel utilisateur

Honeywell

Honeywell S7751A Manuel d'utilisation

Honeywell

Honeywell Vertex Edge Manuel utilisateur

Honeywell

Honeywell enCore Series Manuel utilisateur

Honeywell

Honeywell AC-250NXS Manuel utilisateur

Honeywell

Honeywell TWM 9000 Schéma de câblage

Honeywell

Honeywell RABO Manuel utilisateur

Honeywell

Honeywell QX Manuel utilisateur

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Manuel utilisateur

Honeywell

Honeywell BENDIX/KING KRA 405 Manuel utilisateur

Honeywell

Honeywell E-Mon Comment utiliser

Honeywell

Honeywell AreaRAE Pro Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur