Honeywell ControlEdge 900R04-0200 Manuel utilisateur

ControlEdge PLC and ControlEdge RTU

Getting Started

RTDOC-X287-en-152A

April 2019

Release 152

ControlEdge PLC

ControlEdge RTU

DISCLAIMER

This document contains Honeywell proprietary information.

Information contained herein is to be used solely for the purpose

submitted, and no part of this document or its contents shall be

reproduced, published, or disclosed to a third party without the

express permission of Honeywell International Sàrl.

While this information is presented in good faith and believed to be

accurate, Honeywell disclaims the implied warranties of

merchantability and fitness for a purpose and makes no express

warranties except as may be stated in its written agreement with and

for its customer.

In no event is Honeywell liable to anyone for any direct, special, or

consequential damages. The information and specifications in this

document are subject to change without notice.

CONTENTS

Contents 3

Chapter 1 - About this guide 7

Chapter 2 - Overview 11

Chapter 3 - Hardware 15

ControlEdge 900 platform 15

Hardware components 16

Installing the assembly 24

Wiring and cabling 25

I/O network Topology 27

Power on 31

ControlEdge 2020 platform 31

Hardware components 32

Installing the assembly 37

Wiring and cabling 37

I/O network topology 39

Power on 39

Chapter 4 - Software 41

Installing ControlEdge Builder 41

Launching ControlEdge Builder 41

Checking firmware versions 42

Creating a project 42

Configuring hardware 44

Setting controller name 44

Configuring the controller IP address 44

Configuring controller start up 45

Contents

Configuring controller redundancy 46

Configuring an I/O module 47

Configuring serial modules 49

Configuring a controller simulator 52

Programming with IEC 61131-3 58

Adding a library 58

Creating a data type 58

Creating a variable 61

Creating a Programming Organization Unit 62

Associating a program to a task 64

Compiling a project 65

Chapter 5 - Operating 67

Connecting a controller 67

Downloading a project to the controller 68

Configuring date/time 69

Setting time source 69

Setting time zone 70

Upgrading firmware 70

Upgrading firmware for a non-redundant controller 71

Upgrading firmware for a redundant controller 72

Upgrading EPM firmware 75

Upgrading ControlEdge 900 I/O module firmware 76

Upgrading serial module firmware 77

Upgrading ControlEdge 2020 Expansion I/O firmware 78

Upgrading the FDAP and field device firmware via Wireless 79

Upgrading the field device firmware 79

Upgrading the FDAP firmware 81

Uploading a project 82

Contents

Chapter 6 - Communication 83

Configuring Modbus 83

Configuring a Modbus Slave 83

Configuring a Modbus TCP Master 84

Configuring a Modbus Serial Master 86

Configuring EtherNet/IP devices 92

Configuring OPC UA 94

Configuring an OPC UA Server 94

Configuring an OPC UA Client 97

Communicating with Experion via OPC UA 99

Configuring an OPC UA server 99

Publishing to Experion 100

Configuring DNP3 Slave 100

Communicating with Experion via DNP3 102

Configuring a DNP3 slave 102

Publishing to Experion 102

Configuring HART 103

Configuring a HART-IP Server 103

Configuring a HART Function Block 104

Configuring CDA 106

Installing ControlEdge integration service 107

Configuring a CDA Responder 108

Publishing to Experion 110

Configuring Wireless I/O 111

Configuring User Defined protocol 113

Chapter 7 - Application 115

FDM integration 115

Getting started with FDM 115

Contents

Updating the FDM license 115

Configuring FDM for ControlEdge PLC/RTU network 116

Building networks 118

Chapter 8 - Security 119

Logon feature 119

Setting operating modes 119

Built-in Firewall 122

Configuring IPsec 122

Notices 124

Contents

CHAPTER

1ABOUT THIS GUIDE

Revision history

Revision Date Description

A April 2019 Initial release of this document

Intended audience

This documentation allows the following audience to quickly startup

ControlEdge PLC and ControlEdge RTU system: Users who plan,

install, configure, or operate ControlEdge PLC and ControlEdge RTU

running the eCLR (IEC 61131-3) execution environment.

Prerequisite skills

Knowledge of SCADA systems and experience of working in a

Microsoft Windows environment are required.

Introduction to ControlEdge Technology

Item Description

ControlEdge

PLC

ControlEdge 900 controllers running the eCLR (IEC 61131-3) execution

environment with PLC software options configured with ControlEdge

Builder.

ControlEdge

RTU

ControlEdge 2020 controllers running the eCLR (IEC 61131-3)

execution environment with RTU software options configured with

ControlEdge Builder.

ControlEdge

UOC

ControlEdge 900 controllers running the Honeywell control execution

environment (CEE) configured with Experion Control Builder.

Special terms

The following table describes some commonly used industry-wide

and Honeywell-specific terminology:

Terminology Description

ACE Application Control Environment

Adapter A communication device which connects to the EtherNet/IP network to

serve data from a set of devices or modules underneath it. Adapter

typically supports I/O connectivity from Scanners via implicit

EtherNet/IP connections.

Assembly A set of data passed between a Originator and a Target after an implicit

I/O connection has been established on an EtherNet/IP network.

CDA Control Data Access

ControlEdge

Builder

A integrated configuration tool to design, configure, program and

maintain ControlEdge controllers.

CPM Control Processor Module

DTM Device Type Manager

EDS Electronic Data Sheet. A text file which specifies all the properties of an

EtherNet/IP device necessary for a Scanner module to communicate

with it. EDS files my be used in the first step of creating an I/O module

or device type for interfacing to an EtherNet/IP device.

EPM Expansion Processor Module

Expansion

I/O rack

I/O rack with EPM installed

Expansion

IOM

I/O Module (IOM) external to the CPM that expand the I/O capacity

FDAP Field Device Access Point

FDM Field Device Manager

FTE Fault Tolerant Ethernet

HMI Human Machine Interface

IOTA Input Output Termination Assembly

Left End

Plate

Left end plate is used only in multi-row 2020 I/O systems. It starts a new

row of IOMs and provides connections for 24Vdc supply to the row

along with I/O Network connections.

Local I/O

rack

I/O rack with CPM installed (non-redundant)

Mixed IOM Mixed input/output module, which supports DC current or voltage type

Chapter 1 - About this guide

Terminology Description

signals, such as analog input, analog output, digital input, digital output

and pulse input.

Onboard

IOM

I/O Module (IOM) 'onboard' with the CPM

OPC UA An industrial machine-to-machine (M2M) communication protocol is

developed by the OPC Foundation, which provides a path forward from

the original OPC communications model (namely the Microsoft

Windows only process exchange COM/DCOM) to a cross-platform

service-oriented architecture (SOA) for process control, while enhancing

security and providing an information model.

Originator Originator is the controller that initiate any data exchange with

EtherNet/IP devices on the EtherNet/IP network.

PSM Power Status Module

PSU Power Supply Unit

Redundant

CPM Rack

Rack installed redundant CPM

Right End

Plate

A right end plate is required at the end of each row of expansion I/O

modules, including the row connected to a controller. It allows

additional rows to be added or terminates the I/O network.

RIUP Removal and Insertion Under Power

RPI Requested Packet Interval. The repetitive interval by which assemblies

are periodically transported over EtherNet/IP I/O connections between

Producer and Consumer.

RTU Remote Terminal Unit

SCADA Supervisory Control and Data Acquisition

Scanner A device which connects to the EtherNet/IP network to act as a client of

other EtherNet/IP connected devices. ControlEdge 900 Controller acts

as EtherNet/IP Scanner. It connects to and exchanges data with

Adapters of Modular IO stations, directly connected devices and

Rockwell AB ControLogix controllers.

SIM-300 Simulation for C300

SIM-ACE Simulation for ACE

Target Target is the EtherNet/IP device that address any data requests

Chapter 1 - About this guide

Terminology Description

generated by the controller.

UIO Universal Input/Output Module

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur