Honeywell 10260S series Mode d’emploi

62-86-33-26 Page 1 of 5

10260S Series Actuators

Auto-Manual Switch Replacement Instruction

Document Number

Form: 62-86-33-26

Effective: 06/01

Supersedes: none

Overview

These instructions apply to the following kit: 51500581-501 Auto-Manual Switch Kit and its application to

the 10260S Series Actuators.

Summary

The AUTO-MANUAL switch of the 10260S Actuator is used as a manual override to drive the actuator

motor to position during set up. The Auto-Manual switch kit contains the components needed to add the

switch function to your actuator, or replace a defective switch. Follow the procedure in Table 1 to install the

Auto-Manual switch.

Tools Needed

To perform the replacement procedure, you will need the following tools:

•Medium Flat-blade screwdriver

•Medium Phillips screwdriver

•Small jeweler’s screwdriver set

•Small adjustable wrench

•Needle-nosed pliers

•Heat gun

Procedure

WARNING

Disconnect power before accessing components inside the actuator.

ATTENTION

When working with Printed Wiring Assemblies (PWAs) always protect against electrostatic discharge by

wearing a grounded wrist strap.

Auto-Manual Switch Instruction, continued

Page 2 of 5 62-86-33-26

AUTO-MANUAL

Switch

Terminal Panel

Figure 1 AUTO-MANUAL Switch Location

Table 1 AUTO-MANUAL Switch Installation Procedure

Step Action

1 Remove AC power to the actuator.

2 Remove four screws and the terminal panel cover from the actuator. See Figure 1

3 Remove two screws and pull out the terminal panel from the actuator case.

NOTE: It may be necessary to loosen the external cable entrance on the side of the actuator case to

gain greater access to the AUTO-MANUAL switch location behind the terminal panel.

Procedure continued on next page

⇒

Auto-Manual Switch Instruction, continued

62-86-33-26 Page 3 of 5

Step Action

4 If replacing the switch, disconnect switch wires and remove switch:

•Carefully disconnect auto-manual switch wires at the rear of the terminal panel from the following

lugs: TB1-1, TB1-8,

TB1-9, TB2-12,

TB2-13, TB2-10, TB2-11.

(Looking at the rear of the terminal panel - TB1 is the top terminal board. TB1-1 is the rightmost

terminal on the top terminal board.)

•Disconnect auto-manual switch wires from the connector at P6-1 and P6-2 on the main PWA.

•Remove switch knob by loosening the set screw and then sliding it off the shaft.

•Remove nut securing switch to side of case.

•Pull switch out of case.

5 Slide heat shrink tubing over the body of the new switch so it covers the soldered wire terminals. With

a heat gun, apply hot air to the shrink tubing to seal the wire terminals of the switch.

6 Install new switch:

•Remove plug from access hole in actuator case, (if present) where switch shaft will be installed.

See Figure below.

•.Attach switch label to side of case.

•Remove nut from threads on switch. Insert switch shaft through case access hole. Carefully

rotate switch until is seats in case. Make sure the stub engages the small hole.

•Screw the nut onto the switch shaft and tighten it securely.

•Attach knob to shaft with set screw on flat side of shaft.

AUTO-MANUAL

Switch

Nut

Knob

Label

7 Identify the correct terminal lugs on the back of the terminal panel for connecting the switch wires.

Procedure continued on next page

⇒

Auto-Manual Switch Instruction, continued

Page 4 of 5 62-86-33-26

Step Action

8 Connect switch wires:

•If adding (not replacing) the switch, remove blue and orange wires from TB1-8 and TB1-9.

Connect blue wire to TB2-13 and orange wire to TB2-12.

•If adding or replacing the switch, one at a time connect auto-manual switch wires as follows:

AUTO-MANUAL

Switch Wires

TO: Terminal Panel Lugs

Black

White

Brown

Green

Violet

Orange

Red

TB1-1

TB1-8

TB1-9

TB2-12

TB2-13

TB2-10

TB2-11

Red (24 AWG) Æ

White (24 AWG) Æ

TO: Main PWA Connector

P6-1

P6-2

NOTE: Some terminal lugs have dual (piggyback) wires attached; make sure the wires are attached to

the correct terminals. Make sure piggyback wires on outermost terminals are facing the inner

terminals, not facing away from the terminals. For example, TB1-1 should have its piggyback terminal

positioned between TB1-1 and TB1-2.

9 Reinsert the terminal panel back into the actuator case being careful not to pinch any wires. Secure

terminal panel with two screws.

10 Install a new gasket and replace the terminal panel cover. Secure with four screws.

11 Reapply AC power to the actuator.

12 Verify actuator configuration and check AUTO-MANUAL switch for correct function.

13 Return actuator to service.

Auto-Manual Switch Instruction, continued

Sensing and Control

Honeywell

11 West Spring Street

Freeport, IL 61032

62-86-33-26 06/01 Printed in USA www.honeywell.com/sensing

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship.

Contact your local sales office for warranty information. If warranted goods are returned to Honeywell

during the period of coverage, Honeywell will repair or replace without charge those items it finds defective.

The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied,

including those of merchantability and fitness for a particular purpose. Specifications may change

without notice. The information we supply is believed to be accurate and reliable as of this printing.

However, we assume no responsibility for its use.

While we provide application assistance personally, through our literature and the Honeywell web site, it is

up to the customer to determine the suitability of the product in the application.

Table des matières

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell SILENT KNIGHT SK-Control Manuel

Honeywell

Honeywell VCA Series Manuel utilisateur

Honeywell

Honeywell DC1000 SERIES Manuel utilisateur

Honeywell

Honeywell HW-AV-LTE-M Manuel utilisateur

Honeywell

Honeywell AutoRAE 2 Manuel utilisateur

Honeywell

Honeywell V4055A Manuel d'utilisation

Honeywell

Honeywell VU443A Manuel d'utilisation

Honeywell

Honeywell Enhanced Micro TDC 3000 Manuel utilisateur

Honeywell

Honeywell HJK7000 UltraKey Plus Mode d’emploi

Honeywell

Honeywell Excel Web XL1000A Manuel utilisateur

Honeywell

Honeywell WEB-VA00IB24NM Manuel utilisateur

Honeywell

Honeywell MN7505 Manuel utilisateur

Honeywell

Honeywell SUPER TRADELINE L4064B Manuel utilisateur

Honeywell

Honeywell Spyder 5 Manuel utilisateur

Honeywell

Honeywell EXCEL 10 W7753A Manuel utilisateur

Honeywell

Honeywell Lyric Manuel d'instructions

Honeywell

Honeywell Lyric LCP300-LC Fiche d'information produit

Honeywell

Honeywell H112 Manuel utilisateur

Honeywell

Honeywell CP-UL1012S Manuel utilisateur

Honeywell

Honeywell SHC Series Manuel utilisateur

Honeywell

Honeywell SmartValve SV9510 Manuel utilisateur

Honeywell

Honeywell VR8245 Manuel utilisateur

Honeywell

Honeywell 9782 Series Manuel utilisateur

Honeywell

Honeywell Elster Jeavons J125 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur