Honeywell EVOTOUCH CONTROLLER Manuel utilisateur

Installation | Installation | Installatie | Installation | Installazione

evotouch

The Honeywell evotouch comfort control

system is a programmable zoning controller

with the following key features:

Features

• Largetouch-screendisplayforintuitive

operation by ﬁnger.

• Wallortable-topmounting.

Conguration

• Step-by-stepcongurationprocedure

bindsthecontrollertoeachofthe

devicesinthesystem.

• ChoiceofGuidedConguration,

forsimpleapplications,orExpert

Conguration,forcustomisingthe

conﬁguration.

 Note:evohomesystempacksarealready

precongured(seesystempackcontents

sheet).

Programmability

• Upto6periodsperdayineachofthe8

zones.

• Holidaymodereducesthetemperature

for1to99days.

• Economymodereducesthetemperature

settingsinallzones,toreducefuelbills.

Control

• Wirelesscontroltoboiler,radiator

controllers,roomsensors,andunder

ﬂoor heating controllers.

• Independentcontrolofupto8zones,to

optimisecomfortandminimiseenergy

usage.

• OptimumStartfeatureautomatically

calculates when to start heating to

achieve the correct temperature.

• AutomaticSummer/Wintertimechange.

Future expansion

• AUSBport,forfutureupdates.

Installation

Theproductisshippedwithpre-charged

batteries.However,formaximumtimeoffthe

dock,placetheproductoncharge.

Two mounting options are available:

• Awall-mounteddock.

• Atabletopstand.

Whenremovedfromthestand/dockthe

evotouchwillremainpoweredforabout

2hoursbeforeneedingtobereplacedfor

charging.

Productoverview

ENGLISH

Table-topstand

Theevotouchcanbepoweredfromthe

table-topstand.

• Attachtothestandasshown.

Removefrontcovertoexchangecoverplate

or access batteries.

Remove tab to activate batteries.

Batteriesandfrontcover

Rechargeable batteries. Replace with

AA1.2VNiMH2000-2400mAhbatteriesonly.

✓

✗✗

Installation instructions for wall mounting

StandardEU

SchukoWallbox

Minimum

depth

40mm

Insertwiresintopowermodule,observing

correct polarity

Pushpowermoduleintowallboxwithmains

wiring to the rear

Thepowermodulecanbeinstalledina

differentlocationfromtheevotouchunit.

Disconnect low voltage cable from wallplate

terminalblockandextendtheconnectionby

up to 10m max. using 1.0mm² cable. If smaller

sizecableisusedthemaximumdistancewill

reduce(e.g.5m max with 0.5mm² cable).

Observecorrectpolaritywhenconnectingthe

extensioncable.PowerSupplyCablewiresare

Red(+),Black(-).

Attention:Exceedingthemaximumcable

lengthcouldcausesystemmalfunction!

Attachwallplatetowallboxorsurface

(Powermoduleremote).

Optionalspacerforsurface

mounting.

1.2–1.5m

Positionwallboxataheightof1.2m-1.5m.

Caution:Isolatepowersupplyandmakesafebeforewiring

theunittopreventelectricshockandequipmentdamage.

Installationshouldbecarriedoutbyacompetentperson.

Wiresshould

protrude55mm

230V~mains.

230V~

mains.

Usescrewdriver

with 2.5mm

head

Remove

protective ﬁlm

Knock out

requiredholes

Attachevotouchto

wallplate

Notused

+ – X Y

Setting the language, date, and time

The ﬁrst time you apply power to the

evotouchyouwillbepromptedtoselecta

language for the user interface:

• Presstheappropriatelanguage.

Youwillthenbepromptedtosetthedate:

• Press or tosettheday,month,and

year respectively.

• PressDONEtoproceedtosettingthe

time.

• Press or tosetthehourand

minutes respectively.

You can optionally press CLOCK SETTINGS

tochangethetimeformatbetween24HR

and12HR,andchooseautomaticDaylight

Savingtime:

• PressDONEtoproceedwith

conﬁguration.

System conguration

Asequenceofscreensthenguides

you through an automatic conﬁguration

procedure:

• PressYEStoproceed.

YoucanalsoenterGuidedConguration

at any time by pressing the MENU button

for10seconds,andthenselecting

GUIDED CONFIG from the SYSTEM

CONFIGURATION menu.

Settingupevotouch

ENGLISH

Binding

GuidedCongurationbindseachofthe

controldevicesandsensorstoevotouch,to

ensure that the wireless communication is

working correctly.

Afterbindingeachdevice,aprompt

showswhetherbindingwassuccessful;for

example:

Bindingcanfailforthefollowingreasons:

- Thedeviceisnotswitchedon.

- Thedeviceistoofaraway.

- Therearetoomanysolidobjectsinthe

pathtothedevice.

Correcttheproblemandtryagain.

Editing names

During conﬁguration you are given the

optionofeditingthenamesusedtoidentify

the zones in the system. These are the

names seen by the user on the main Home

screen.

Toeditanamethefollowingscreenis

displayed:

• Presstodeletecharacters.

• PressABCtoenterupper-caseletters,

abctoenterlower-caseletters,or123 to

enterdigits.

• Presstheblankkeytoenteraspace.

• PressDONEwhennished.

Conguring mixed applications

TheGuidedCongurationdescribedonthe

following pages assumes all your zones use

thesametypeofcontrol.Ifyouhaveamixed

application,suchas5zoneswithradiator

controland3zoneswithunderoorheating

control,youcansetupthecongurationas

follows:

• UsetheGuidedCongurationto

congurethe5zonesforradiatorcontrol.

• UsetheADD ZONEoptiontoaddthe

3zonesforunderoorheatingcontrol;

see Adding a zone,page9.

• FinallyusetheSYSTEM

CONFIGURATION menu BINDING AND

RF TESToption,doingtheRFtestfor

eachzone.Formoreinformationseethe

Extended Installation Guide.

Conguration–GeneralFeatures

GuidedCongurationistherecommended

optionthersttimeyoucongureevotouch,

asitleadsyouthroughtheessentialstepsin

setting up a system.

• AtthepromptpressYEStoproceed.

Heat demand control

The ﬁrst step is to specify whether the

systemincludesaheatdemandboiler:

• PressNO or YES as appropriate.

IfyoupressedYESproceedasfollows.

IfyoupressedNO skip to the section

Applications below.

Ifthesystemincludesheatdemandcontrol,

thenextstepistocongurethewirelesslink

to the boiler controller:

• PressBIND.

ForinformationaboutbindingseeBinding

on the previous page.

• WhenbindingissuccessfulpressNEXT.

Thefollowingpromptisdisplayed:

• Installthedemanddeviceinitsproper

locationandputthedeviceintothetest

mode.

• PressNEXTwhenready.

Thefollowingpromptisdisplayed:

• PressNEXT.

Applications

The following menu allows you to specify

whichothercomponentsinthesystemneed

tobecongured:

• Selectthetypeofapplicationyouare

conﬁguring.

GuidedConguration

ENGLISH

Inasimplesystem,withevotouchacting

asthethermostattoaheatdemandboiler,

select Thermostat (1 zone),andasingle

zone will automatically be set up for you.

Inalargersystem,withradiatorcontrol

orunderoorheatingprovidingindividual

controlofseparateareas,youwillbe

promptedtosetupeachzone.

Thermostat (1 zone)

IfyouselectedTHERMOSTAT(1zone)the

zonenameisinitiallysettoLIVINGROOM:

• PressLIVING ROOMtoeditthename,

asdescribedinEditing namesearlier,or

NEXT to accept it.

NowproceedasdescribedinSpecifying the

sensors below.

Multizoning radiator heating or

Zone valves

IfyouselectedRADIATORHEATINGor

ZONEVALVESyouneedtospecifythe

number of zones in the system:

• Press or to specify the number of

zones,thenpressNEXT.

Thefollowingscreenletsyoueditthedefault

names chosen for the zones:

• Pressanyzonenametoeditit,as

describedinEditing namesearlier,or

press NEXT to continue.

Ifyouspeciedmorethan6zonespressMORE

toseeoredittheremainingzonenames.

Specifying the sensors

Foreachzonethedisplaypromptsyouto

specify the type of sensor:

• PressINTERNAL or EXTERNAL as

appropriate.

IfyouspeciedEXTERNAL you will then be

promptedtobindthesensor,asdescribed

in Binding earlier in this section.

• PressNEXT to repeat for the sensors in

each zone.

Whenallthezoneshavebeensuccessfully

conguredaconrmationisdisplayed.

•

Press DONE to return to the Home screen.

Note:Onlyonezonecanbecontrolledby

theinternalsensor.Selectingtheinternal

sensor automatically conﬁgures all other

zonestouseexternalsensors.

Addingazone

Thissectionexplainshowtoaddazone

toanexistingconguration,suchasafter

addinganHR80RadiatorControllerto

provideindependentcontrolofaroom.

• PressMENU from the home screen to

displaytheMainMenu.

• PressZONING MENUontheMainMenu

todisplaytheZoningMenu.

• PressZONING CONFIG on the Zoning

Menu.

Thefollowingwarningisdisplayed:

• Pressthebuttonfor5secondstodisplay

theZoningCongurationMenu.

• PressADD ZONE.

Youarerstpromptedtospecifythetypeof

application for the zone:

Formoreinformationaboutapplicationssee

the Extended Installation Guide.

Youarenextpromptedtonamethezone.

Thefollowingmenuthenallowsyoutobind

anactuatorandsensortothezone,andset

uptheschedule:

Forinformationaboutprogramminga

scheduleseetheQuick Start User Guide.

• PressBINDING MODEtobinddevicesto

the new zone.

Youarerstpromptedtobindtheactuatorin

the zone.

• PuttheactuatorinBINDmodeandpress

BIND.

Whenasuccessfulresponsehasbeen

received:

• PressDONE.

Thenextstepistobindasensorinthe

zone. You are given the option of using the

evotouchinternalsensor,oranexternal

room sensor.

Ifthezonecontainstheevotouchcontroller,

andyouwanttousetheinternalsensor,

press INTERNAL.

OtherwisepressEXTERNAL,andyouwill

bepromptedtobindaroomsensorinthe

zone.

• PresstheBIND button on the sensor.

Whenasuccessfulresponsehasbeen

received:

• PressDONE to return to the ADD ZONE

menu.

ENGLISH

Zoning boiler control with

BDR90 Relay module or RF

bridge

Initssimplestsingle-zone

congurationevotouchsensesand

controls the temperature in the main

room,usingitsinternalsensorand

calling for heat from the boiler via the

BoilerRelayorOpenthermBridge

accordingtothedesiredsetpoint.

HR80 radiator control with

central operation

Theevotouchcancontrolupto8zones

usingtheHR80radiatorcontroller.The

evotouch uses the valve position of the

HR80todeterminewhetherornotheat

isrequired.Itwillcontroltheboilervia

theboilerrelayorOpenthermBridge.

In this conﬁguration only the set point

issenttotheHR80s.TheHR80swill

comparethereceivedsetpointto

themeasuredzonetemperatureand

adjustthevalvepositionaccordingly.

Under oor heating control

with central operation and

room units DT92/HCW82

The evotouch can also integrate with

anunderoorheatingcontroller,and

roomunitsDT92/HCW82,toprovide

individualcontrolofupto8rooms.

TheDT92/HCW82roomsensorsand

setpointadjusterscommunicate

directlywithevotouch.

Three simple system applications

Relay module

Boiler Relay or Opentherm Bridge

Boiler

0 .. 100%

ON/OFF

19.

HR80

Relay module

Boiler Relay or Opentherm Bridge

Up to 8 zones

Boiler

0 .. 100%

ON/OFF

19.

Relay module

Boiler Relay or Opentherm Bridge

Antenna

HRA80

Up to 8 zones

Boiler

HCW82

DT92

0 .. 100%

ON/OFF

Underfloor heating

controller

HCE80(R)/HCC80(R)

19.5

Autres manuels pour EVOTOUCH CONTROLLER

Table des matières

Langues :

Autres manuels Honeywell Système de contrôle

Honeywell

Honeywell Farenhyt Series Mode d'emploi

Honeywell

Honeywell W7080A Manuel utilisateur

Honeywell

Honeywell SILENT KNIGHT SK-Zone-6 Manuel utilisateur

Honeywell

Honeywell W180 Manuel utilisateur

Honeywell

Honeywell VR8404 Manuel utilisateur

Honeywell

Honeywell Tema-Voyager Compact Manuel utilisateur

Honeywell

Honeywell Excel 800 Manuel d'installation et d'exploitation

Honeywell

Honeywell BCS 3600 Manuel utilisateur

Honeywell

Honeywell W180 Manuel utilisateur

Honeywell

Honeywell VR8205 Manuel utilisateur

Honeywell

Honeywell Excel 5000 System Series Manuel utilisateur

Honeywell

Honeywell MRP-2002E Manuel utilisateur

Honeywell

Honeywell Excel 500 Manuel utilisateur

Honeywell

Honeywell RP-2002 Manuel utilisateur

Honeywell

Honeywell SPZ-8000 Manuel

Honeywell

Honeywell LYNX Touch L7000 Series Manuel utilisateur

Honeywell

Honeywell ComfortPoint Open Manuel d'installation et d'exploitation

Honeywell

Honeywell vk41 series Manuel utilisateur

Honeywell

Honeywell XLS80e Manuel utilisateur

Honeywell

Honeywell R4184D Manuel utilisateur

Honeywell

Honeywell SmartVFD Manuel utilisateur

Honeywell

Honeywell Experion LX 8 series Manuel utilisateur

Honeywell

Honeywell Experion LX Manuel

Honeywell

Honeywell MCBA14C Manuel de service

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur

EMKO

EMKO TRANS-SYNCRO Manuel utilisateur

Dover

Dover TWG GC ELEMENT II Manuel de programmation