Honeywell Silent Knight 5860 Manuel technique

5860/5860R

Remote Fire Annunciator

Product Installation Document

Document 151042:E 2/15/2022 ECN: 151062

1 Description

The 5860 (gray) and 5860R (red) are optional 4x20 remote annunciators

that can be surface or flush-mounted.

2 Compatibility

The 5860/R is compatible with Honeywell Silent Knight FACPs. For

more information, see the FACP Installation manual.

3 Specifications

4 Installing the 5860/R

5860/R installation involves the following steps:

1. Ensure power is turned off at the panel.

2. Mount the 5860/R in the desired location.

3. Connect the 5860/R to the panel (see Figure 5).

4. Use the DIP switches on the back of the 5860/R to assign an ID

number. See the FACP Manual for more details.

5. The new 5860/R module must be added to the system through

programming. The JumpStart®Auto-programming feature will add

the module automatically. Refer to the FACP Manual for more

information.

5 Mounting

The 5860/R comes from the factory fully assembled. You must disas-

semble it for mounting. To disassemble the annunciator, use a 5/64” hex

wrench to remove the set screws, located on the bottom of the annuncia-

tor bezel.

FIRE ALARM ANNUNCIATOR

Figure 1 5860/R Remote Annunciator

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 58 mA

Alarm: 68 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

1".25

(3.175cm)

6.44"

(16.35cm)

8"(20.64cm).125

7".375

(18.73cm)

1”

.25

(3.175cm)

Figure 2 Annunciator Dimensions

backbox bezel

side

view

5860/5860R Installation Document — P/N 151042:E 2/15/2022 2

5.1 Surface Mounting

The 5860/R can be mounted directly to a surface or can be attached to a

single, double, or four-square electrical box. Trim Ring Kit 5860TG

(gray) and 5860TR (red) available for use when surface mounting.

1. Drill holes in the surface to match the screw holes on the backbox.

Refer to Figure 4.20 for locations.

2. Fit the trim ring over the backbox, if used.

3. Attach the backbox to the wall using screws provided.

5.2 Flush-Mounting

1. Cut a hole in the sheet rock to the following dimensions: 8.25” W x

6.625” H. If an electrical box is used, the box must be 1.375” back

from face of wall to accommodate the annunciator.

2. Remove knockout holes as needed for wires.

3. Fit the annunciator backbox into the hole and stabilize with

mounting wires. Angle the mounting wires into the first hole past

the sheet rock. Secure the wires behind the screws as shown in

Figure 4. When all four wires are in place, the backbox should fit

snugly into the hole in the sheetrock.

4. After the annunciator wiring to the panel has been completed (refer

to Figure 4.22), replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws on the

bezel.

5.2.1 Flush-Mounting with an Electrical Box

The 5860/R annunciator can be used with the following types of electri-

cal boxes: 4S, single-gang, and double-gang.

If an electrical box is used, the box must be 1.375” back from the face of

the wall to accommodate the annunciator. Studs used with an electrical

box must be 2x4” (or larger).

6 Wiring Connections

Wire the 5860/R to the FACP as shown below.

Figure 3 Trim Ring for Surface-mounting

backbox

trim ring

Attach second set of wires to top of backbox.

Secure wires behind screw.

Insert wires at an angle into the

first holes past sheetrock.

Figure 4 Flush Mounting the Backbox

SBUS OUT

–+AB

SB SA S+ S-

12345

Figure 5 SBUS Connections

5860/R

FACP SBUS

supervised,

power-limited,

Class B

Ce manuel convient aux modèles suivants

Autres manuels Honeywell Panneau de contrôle

Honeywell

Honeywell Excel 5000 System Series Manuel utilisateur

Honeywell

Honeywell Domonial CMI Series Guide de l'utilisateur

Honeywell

Honeywell IFP-75 Manuel utilisateur

Honeywell

Honeywell Accenta Manuel utilisateur

Honeywell

Honeywell Notifier NFS-320/E/C Manuel utilisateur

Honeywell

Honeywell Symphony Mode d’emploi

Honeywell

Honeywell AQ25A Series Manuel utilisateur

Honeywell

Honeywell NOTIFIER INSPIRE E10 Manuel de formation

Honeywell

Honeywell Securit 800L Manuel utilisateur

Honeywell

Honeywell NOTIFIER SLC Manuel utilisateur

Honeywell

Honeywell ADEMCO VISTA SERIES Guide d'installation

Honeywell

Honeywell Galaxy 2-44+ Manuel utilisateur

Honeywell

Honeywell SLC Manuel utilisateur

Honeywell

Honeywell Notifier ST.PL4+ Manuel utilisateur

Honeywell

Honeywell Galaxy 18Galaxy Manuel du propriétaire

Honeywell

Honeywell nfs2-3030 Manuel du propriétaire

Honeywell

Honeywell Fire-Lite Alarms MS-9600 Manuel utilisateur

Honeywell

Honeywell FCI Gamewell Flex 404 Manuel utilisateur

Honeywell

Honeywell IQ8Control C Manuel utilisateur

Honeywell

Honeywell AQ250 Series Manuel d'utilisation

Honeywell

Honeywell Accenta Manuel utilisateur

Honeywell

Honeywell NOTIFIER NFW-50X Manuel utilisateur

Honeywell

Honeywell DX Connexion Series Manuel utilisateur

Honeywell

Honeywell AQ252 Series Manuel utilisateur

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques