Hollywood Racks rv1 Guide de configuration rapide
HOLLYWOOD RACKS
Parts Included (Fig. 1):
Item Description Quantity
A welded tube frame 1
B support legs 2 each
C 8mm bolts 4 each
8mm nuts 4 each
8mm flat washers 4 each
8mm split washers 4 each
D 10mm nuts 4 each
10mm flat washers 4 each
10mm split washers 4 each
E locking caster 4 each
RACK VALET ™
Mobile hitch rack storage solution
Fits all 1 ¼” and 2”hitch racks
Assembly & Use Instructions
Tools Required: two adjustable
wrenches or two 13mm (1/2”) and
one 17mm wrench.
Assembly:
1. Per Fig. 2, position the legs (B)
below the frame (A) as shown.
Insert the 8mm bolts (C) through
frame and legs from the bottom up.
Install the 8mm flat washers, then
split washers and 8mm nuts onto
bolts. Tighten securely using the
adjustable or 13mm wrenches.
Be sure rear bolts are installed into
the rear most holes per Fig. 2.
2. Per Fig. 4, carefully press down
on the tab of the caster (E) so it will
not spin. Per Fig. 3, Insert threaded
stem of the caster through the hole.
Install (D) 10mm flat washer, then
split washer and nut onto threaded
stem. Next, hold the caster and
tighten the nut with adjustable or
17mm wrench. Repeat for other
three casters.
Fig. 2
Fig. 3
Fig. 1
LOCKING THE CASTER (Fig. 4): Wearing shoes, gently
press the tab of the caster down with your foot to lock
it. When locked, the caster will not spin or roll. (NOTE:
The tab should not be pressed flat against the wheel. If
by accident it is “over pressed”, you will need to pull it by
inserting a small flat screwdriver between the wheel and
tab, then gently pry it back. UNLOCKING THE CASTER:
Place the tip of your shoe below the tab and lift up.
Fig. 5
Fig. 6
Fig. 7
General Notes: Per Fig. 5: The Rack Valet will accommodate both 1.25” and 2” hitch sizes. Use the upper opening
for 1.25” and lower opening for 2” hitch tubes. Per Fig. 6: The openings are slightly oversized for easy insertion of
the bike rack into the Rack Valet. The bike rack may seem to be a little “wobbly” but it actually is very stable.
Per Fig. 7: For safety reasons, never step or stand on the support legs of the Rack Valet.
Using the Rack Valet: Step 1: Fold the bike rack as if it were flat against the back of your car. Step 2: Lock all
four casters per Fig. 5. Step 3: Insert the bike rack into the Rack Valet. Step 4: Install hitch pin. Step 5: Unlock
the casters and roll the Rack Valet to its destination. If on a downward slope or hill, do not release the Rack Valet
and rack until the casters are locked. Before removing bike rack from Rack valet, be sure to lock the casters.
Never step or stand on the support legs of the Rack Valet. For 2+2 style hitch racks (i.e. Hollywood Sport Rider
4), first install the base 2 bike rack into the Rack Valet, then install the outer 2 bike add-on into the base rack.
Fig. 8
Fig. 9
HOLLYWOOD RACKS Los Angeles, California
Family owned and operated since 1973
For customer service, please email us at
Call 800-747-4085 M-F 8:00 AM –3:00 PM PST
For warranty information, please visit
www.hollywoodracks.com/about
Rack Valet™Patent Pending Model# RV1
V3 022417
www.hollywoodracks.com
Fig. 4
Table des matières
Autres manuels Hollywood Racks Support et étagère
Hollywood Racks
Hollywood Racks SP1-HW - BUZZRIDER Manuel utilisateur
Hollywood Racks
Hollywood Racks Destination HR4200 Guide de l'utilisateur
Hollywood Racks
Hollywood Racks HR1600 Manuel utilisateur
Hollywood Racks
Hollywood Racks Baja 2 Manuel utilisateur
Hollywood Racks
Hollywood Racks HR1450E Manuel utilisateur
Hollywood Racks
Hollywood Racks Sportrider HR1450R Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
