Hitachi CPS240 SVGA Manuel utilisateur

ENGLISH

Projector

CP-S240/CP-X250

CP-S245/CP-X255

User's Manual – Quick Guide

Thank you for purchasing this projector.

WARNING ►Before using this product, please read the "User's Manual -

Safety Guide" and related manuals to ensure the proper use of this product. After

reading them, store them in a safe place for future reference.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this

manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

Contents of package

(1) Projector

(2) Remote control

with two AA batteries

(3) Power cord

(4) RGB cable

(5) Audio/Video cable

(6) Soft case

(7) User’s manuals

(8) Lens cover, Rivet and Strap

(1) (2) (3)

(6)

NOTE • Keep the original packing materials for future reshipment. For

moving the projector, be sure to use the original packing materials. Use special

caution for the lens part.

(7)

(4) (5)

HOME

PAGE UP

PAGE DOWN

END

VIDEO RGBSEARCH

FREEZE

OFF

MAGNIFY

ASPECT AUTO BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

(8)

4:3

(a)

16:9

(a)

Arrangement

WARNING ►Install the projector in a suitable environment according to

instructions of the "User's Manual - Safety Guide".

CAUTION ►This projector has some intake vents also on the bottom. Avoid

blocking vents. Put nothing that is sucked or sticks to the bottom of projector.

(calculated for a full size screen, ±10%)

For the model CP-X250/CP-X255

For the model CP-S240/CP-S245

(b)

(a) Screen

size

[inch (m)]

4 : 3 screen 16 : 9 screen

(b) Projection distance

[m (inch)]

[cm (inch)]

(b) Projection distance [m

(inch)]

[cm (inch)]

min. max. down up min. max. down up

30 (0.8) 0.9 (36) 1.1 (43) 5 (2) 41 (16) 1.0 (39) 1.2 (47) -1 (0) 39 (15)

40 (1.0) 1.2 (48) 1.5 (57) 6 (2) 55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)

50 (1.3) 1.5 (60) 1.8 (72) 8 (3) 69 (27) 1.7 (65) 2.0 (79) -2 (-1) 64 (25)

60 (1.5) 1.8 (72) 2.2 (87) 9 (4) 82 (32) 2.0 (79) 2.4 (94) -2 (-1) 77 (30)

70 (1.8) 2.1 (84) 2.6 (101) 11 (4) 96 (38) 2.3 (92) 2.8 (110) -3 (-1) 90 (35)

80 (2.0) 2.4 (96) 2.9 (116) 12 (5) 110 (43) 2.7 (105) 3.2 (126) -3 (-1) 103 (41)

90 (2.3) 2.8 (109) 3.3 (130) 14 (5) 123 (49) 3.0 (118) 3.6 (142) -4 (-1) 116 (46)

100 (2.5) 3.1 (121) 3.7 (145) 15 (6) 137 (54) 3.3 (132) 4.0 (158) -4 (-2) 129 (51)

120 (3.0) 3.7 (145) 4.4 (174) 18 (7) 165 (65) 4.0 (158) 4.8 (190) -5 (-2) 154 (61)

150 (3.8) 4.6 (182) 5.5 (218) 23 (9) 206 (81) 5.0 (198) 6.0 (238) -6 (-2) 193 (76)

200 (5.1) 6.2 (242) 7.4 (291) 30 (12) 274 (108) 6.7 (264) 8.1 (317) -8 (-3) 257 (101)

250 (6.4) 7.7 (303) 9.3 (364) 38 (15) 343 (135) 8.4 (330) 10.1 (397) -10 (-4) 322 (127)

300 (7.6) 9.2 (364) 11.1 (437) 46 (18) 411 (162) 10.1 (397) 12.1 (476) -12 (-5) 386 (152)

(a) Screen

size

[inch (m)]

4 : 3 screen 16 : 9 screen

(b) Projection distance

[m (inch)]

[cm (inch)]

(b) Projection distance [m

(inch)]

[cm (inch)]

min. max. down up min. max. down up

30 (0.8) 0.9 (36) 1.1 (43) 5 (2) 41 (16) 1.0 (39) 1.2 (47) -1 (0) 39 (15)

40 (1.0) 1.2 (48) 1.5 (58) 6 (2) 55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)

50 (1.3) 1.5 (60) 1.8 (73) 8 (3) 69 (27) 1.7 (66) 2.0 (79) -2 (-1) 64 (25)

60 (1.5) 1.8 (73) 2.2 (87) 9 (4) 82 (32) 2.0 (79) 2.4 (95) -2 (-1) 77 (30)

70 (1.8) 2.2 (85) 2.6 (102) 11 (4) 96 (38) 2.4 (93) 2.8 (111) -3 (-1) 90 (35)

80 (2.0) 2.5 (97) 3.0 (117) 12 (5) 110 (43) 2.7 (106) 3.2 (127) -3 (-1) 103 (41)

90 (2.3) 2.8 (109) 3.3 (132) 14 (5) 123 (49) 3.0 (119) 3.6 (143) -4 (-1) 116 (46)

100 (2.5) 3.1 (122) 3.7 (146) 15 (6) 137 (54) 3.4 (133) 4.0 (159) -4 (-2) 129 (51)

120 (3.0) 3.7 (146) 4.5 (176) 18 (7) 165 (65) 4.0 (159) 4.9 (192) -5 (-2) 154 (61)

150 (3.8) 4.6 (183) 5.6 (220) 23 (9) 206 (81) 5.1 (200) 6.1 (240) -6 (-2) 193 (76)

200 (5.1) 6.2 (244) 7.5 (294) 30 (12) 274 (108) 6.8 (266) 8.1 (320) -8 (-3) 257 (101)

250 (6.4) 7.8 (306) 9.3 (367) 38 (15) 343 (135) 8.5 (333) 10.2 (400) -10 (-4) 322 (127)

300 (7.6) 9.3 (367) 11.2 (441) 46 (18) 411 (162) 10.2 (400) 12.2 (480) -12 (-5) 386 (152)

ENGLISH

Adjusting the projector's elevator

CAUTION ►

If you press the elevator button without holding the projector,

the projector might crash down, overturn, smash your ﬁngers and possibly result

in malfunction. To prevent damaging the projector and injuring yourself, always

hold the projector whenever using the elevator buttons to adjust the elevator feet.

►

Do not incline the projector rightward or leftward. Also do not incline it backward

or forward exceeding 9 degrees. Exceeding these range could cause malfunction,

and could shorten the lifetime of the consumables.

►

Except for inclining by the elevator feet adjustment, place the projector horizontally.

1. After making sure that the projector is cool

adequately, press and hold in the elevator buttons

while holding the projector. The elevator buttons and

the elevator feet are on the both sides.

2. Raise or lower the projector to the desired height

and release the elevator buttons.

When you release the elevator buttons, the elevator

feet will lock into position.

3. If necessary, you can also ﬁnely adjust the height of the projector by twisting

the elevator feet by hand.

Elevator

button

Elevator feet

Connecting your devices

Examples of connection with a computer

* In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2

ports. To change the settings, refer to the AUDIO item in the SETUP menu.

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

RGB IN2

RGB OUT

Audio out RS-232C

RGB out

Stereo mini audio cable

RGB cable

Audio out

RS-232C cable

USB

RGB out

Use the RGB IN OUT

switch to select RGB IN2

(RGB IN2 is selected if

the switch is not pushed

in).

USB cable

Stereo mini

audio cable

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

LAN

LINK

ACT

VIDEO

S-VIDEO

CB/PB

CR/PR

RGB out

RGB cable

LAN

LAN cable

For the models CP-S245/CP-X255

* Only the CP-S245/CP-X255 have a

LAN port.

ENGLISH

Connecting your devices

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Examples of connection with a VCR/DVD player

Audio (R) out

Video out

Audio cable

Audio/Video cable

Audio (R) out

S-Video out S-Video cable

Audio (R) out

Component video out

Audio cable

Audio (L) out

CB/PB

CR/PR

Audio (L) out

Component video cable

In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEO and

COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the SETUP menu.

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2 USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

Y R

AUDIO IN2

AUDIO OUT

CONTROL RGB IN1

RGB IN2USB

RGB OUT

AUDIO IN1

VIDEO

S-VIDEO

CB/PB

CR/PR

RGB IN2

RGB OUT

RGB in

Stereo mini audio cable

Connecting to a monitor (output)

Connecting to a speaker with ampliﬁer (output)

Use the RGB IN OUT switch to select RGB OUT

(RGB OUT is selected if the

switch

is pushed in).

RGB cable

Audio in

Putting batteries into the remote control

WARNING ►Always handle the batteries with care and use them only as

directed. Improper use may result in battery explosion, cracking or leakage,

which could result in ﬁre, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries speciﬁed. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

• Make sure the plus and minus terminals are correctly aligned when loading a

battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not allow a battery in a ﬁre or water. Keep batteries in a dark, cool and dry place.

•

If you observe a leakage of a battery, wipe out the ﬂower and then replace a battery.

If the liquid adheres to your body or clothes, rinse well with water immediately.

1. Remove the battery cover.

Slide back and remove the battery cover in the direction of

the arrow.

2. Insert the batteries.

Align and insert the two AA batteries according to their plus

and minus terminals as indicated in the remote control.

3. Close the battery cover.

Replace the battery cover in the direction of the arrow and

snap it back into place.

Putting batteries into the remote control / Connecting the power supply

Connecting the power supply

WARNING ►Please use extra caution when connecting the power cord, as

incorrect or faulty connections may result in ﬁre and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, contact

your dealer to newly get correct one.

• Only plug the power cord into an outlet rated for use with the power cord's

speciﬁed voltage range.

• Never modify the power cord. Never attempt to defeat the ground connection of

the three-pronged plug.

1. Connect the connector of the power cord

to the AC inlet of the projector.

2. Firmly plug the power cord's plug into

the outlet.

AC inlet

Connector

of the power cord

ENGLISH

Zoom knob

Focus ring

Operating

WARNING ►

When the power is on, a strong light is emitted. Do not look into

the lens of projector. Also do not peep at the inside of projector through a hole.

Turning on the power

1. Set the power switch to the ON position.

2. Press the STANDBY/ON (projector or

remote control) button.

Displaying

1. To select an input signal, use the button of INPUT (projector), or the buttons

of RGB, VIDEO or SEARCH (remote control).

2. To change the aspect ratio, use the button

ASPECT (remote control).

3. To adjust the zoom and focus, use the

zoom knob and the focus ring.

Turning off the power

This product is able to turn off the main power during the cooling. However, please

pay special attention to below two points when you do:

(1) Please do not turn the projector on again for at least 1 minute in this case.

Neglect could shorten the lifetime of the lamp.

(2) During use or immediately after use, do not touch around the lamp and vents

of the projector. It could cause a burn.

1. Press the STANDBY/ON (projector or remote control) button.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON (projector or remote control) button again while the

message appears.

The projector lamp will go off, and the POWER

indicator will begin blinking in orange. Then the

POWER indicator will stop blinking and light in

steady orange when the lamp cooling is complete.

Make sure that the power indicator lights in steady

orange, and set the power switch to the OFF position. The POWER indicator will go off.

POWER

(Blinking in orange)

POWER

(Steady orange)

POWER POWER

(Blinking in green) (Steady green)

POWER

(Steady orange)

SEARCH button

RGB button

VIDEO button

ASPECT button

HOME button

MAGNIFY

ON button

OFF button

END button

FREEZE button

POSITION button

ESC button

STANDBY/ON button

AUTO button

BLANK button

PAGE UP button

VOLUME button

MUTE button

PAGE DOWN button

KEYSTONE button

MENU button

Cursor buttons

▲,▼,◄,►

ENTER button

RESET button

Control buttons / Remote control

Control buttons

Remote control

LAMP indicator

TEMP indicator

POWER indicator

Cursor buttons

▲,▼,◄,►

STANDBY/ON button

INPUT button

Battery cover

(on the back)

HOME

PAGE UP

PAGE DOWN

END

VIDEO RGBSEARCH

FREEZE

OFF

MAGNIFY

ASPECT AUTO BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

ENGLISH

Lamp

WARNING HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp can break

with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn

over time. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them. In addition, when the bulb bursts, it is

possible for shards of glass to ﬂy into the lamp housing, and for gas containing

mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not

put it in a trash. Dispose of it in accordance with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in

the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug

the power cord from the outlet, and make sure to request a replacement

lamp from your local dealer. Note that shards of glass could damage the

inside of the projector, or cause injury during handling, so please do not

try to clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does),

ventilate the room well, and make sure not to breathe the gas that

comes out of the projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

Handling the lamp while hot can cause burns, as well as damaging the

lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is suspended from

the ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. To replace the

lamp, make sure that the screws are tightened firmly. Loose screws

could result in damage or injury.

• Use only the lamp of the speciﬁed type.

• If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, contact your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could cause it dark, not to light

up or to burst. When the pictures appear dark, or when the color tone

is poor, please replace the lamp as soon as possible. Do not use old

(used) lamps; this is a cause of breakage.

Disconnect

the plug

from the

power

outlet

Lamp (continued)

A lamp has a ﬁnite product life. Using the lamp for long periods of time could

cause the pictures darker or the color tone poor. Note that each lamp has a

different lifetime, and some may burst or burn out soon after you start using them.

Preparation of a new lamp and early replacement are recommended.

To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number = DT00731.

1. Turn the projector off, and unplug the power cord. Allow the lamp to cool for

at least 45 minutes.

2. Prepare a new lamp.

If the projector is mounted on the ceiling, or if the lamp has broken, also ask

the dealer to replace the lamp.

In the case of replacement by yourself,

3. Loosen the lamp cover screw (marked by arrow)

and then slide the lamp cover to the side to

remove it.

4. Loosen the 2 screws (marked by arrow) of the

lamp, and slowly pick up the lamp by the handles.

5. Insert the new lamp, and retighten ﬁrmly the two

screws that are loosened in the previous process

to lock it in place.

6. Slide the lamp cover back in place and ﬁrmly

fasten the lamp cover screws.

7. Turn the projector on and reset the lamp time

using the LAMP TIME function in the OPTION

menu.

(1) Press the MENU button to display a menu. Only

when the EASY MENU has appeared, please

perform the next step (2).

(2) Point at the “Go To Advance Menu …” in the menu

using ▼/▲ button, then press the ► button.

(3) Point at the “OPTION” in the left column of the

menu using ▼/▲ button, then press the ► button.

(4) Point at the ”LAMP TIME” using ▼/▲ button, then

press the ► button. A dialog will appear.

(5) Press the ▲ button to select “RESET” on the

dialog. It performs resetting the lamp time.

Lamp cover

Screw

Handle

Screws

NOTE • Please reset the lamp time only when you have replaced the lamp,

for a suitable indication about the lamp.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Projecteur

Hitachi

Hitachi CP-WX1100 Manuel d'utilisation et d'entretien

Hitachi

Hitachi CP-D32WN Manuel utilisateur

Hitachi

Hitachi CP-A302WNM Manuel utilisateur

Hitachi

Hitachi CP-CX300WN Manuel utilisateur

Hitachi

Hitachi CPX305 - XGA LCD Projector Instructions d'installation et d'entretien

Hitachi

Hitachi CP-SX8350 Manuel utilisateur

Hitachi

Hitachi CPX605 - 4000 Lumens XGA LCD Projector Manuel utilisateur

Hitachi

Hitachi CPWX8 Manuel utilisateur

Hitachi

Hitachi CPX1 Series Manuel utilisateur

Hitachi

Hitachi CP-X440 series Manuel utilisateur

Hitachi

Hitachi X807 - CP XGA LCD Projector Mode d’emploi

Hitachi

Hitachi CP-S225WA Manuel utilisateur

Hitachi

Hitachi CP-TW2505 Manuel utilisateur

Hitachi

Hitachi CP-X990 Manuel utilisateur

Hitachi

Hitachi CP-EX5001WN Manuel utilisateur

Hitachi

Hitachi Innovate CP-X2521WN Manuel utilisateur

Hitachi

Hitachi CP-X9110 Manuel utilisateur

Hitachi

Hitachi CP-X885W Manuel utilisateur

Hitachi

Hitachi CP-RS56W and Mode d’emploi

Hitachi

Hitachi FT-01 Manuel utilisateur

Hitachi

Hitachi CP-DW10N Manuel utilisateur

Hitachi

Hitachi CP-EX3051WN Document technique

Hitachi

Hitachi CP-WX410 Manuel utilisateur

Hitachi

Hitachi CP-RX61 series Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur