Hitachi Highly WHP07600PSDPC9KQ Manuel utilisateur

HitachiHighly

Rollkolbenverdichter

Rotary Compressors

Spezifikation

Installation Manual

WHP07600PSDPC9KQ

RIES GmbH, Rudolf-Diesel-Str. 10, D 64569 Nauheim, GERMANY

Phone: +49 6152 9741 0, Fax: +49 6152 9741 21, Email: [email protected], Website: www.ries-gmbh.de

R 290

30,7 cm3/rev

900 - 7200 min-1

CONTENTS

————— 1～4

WHP07600PSDPC9KQ SPECIFICATION

1. SCOPE

2.SPECIFICATION OF THE MODEL

3.THE PARAMETER OF MOTOR

4.CHARACTERISTICS

5.PARTS AND DRAWING LIST

—— 5～15

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

——————— 16

CHECK UPON DELIVERY

1. BASIS FOR CHECKING UPON DELIVERY

2. RULE FOR CHECKING UPON DELIVERY

——————————— 17～29

DRAWINGS

————— 30

SPECIFICATION REVISION RECORD

SUBJECT

M od el W HP0 76 00 PS DPC 9K Q SP ECI FI CA TI ON PAGE：1/30

1. SCOPE

This specification is applied to SHANGHAI HIGHLY Heat pump water heater

compressor.

2. SPECIFICATION OF THE MODEL

Item Spec

2.1 Model Type WHP07600PSDPC9KQ

2.2 Power source input to inverter Rated voltage / Rated frequency/Phase

380V/50Hz/3Ф

2.3 Output 1480W(@3600 min-1)

2.4 Application Heat pump water heater

2.5

Performance

Item Rated Condition

Rotational speed 3600 min-1

Nominal Heating Capacity 7475W

Motor input 1580W

Current 6.4A

COP(see*) 4.73

Evaporating temp. 7.2℃

Condensing temp. 54.4℃

Liquid temp. entering

expansion valve. 46.1℃

Return gas temp. 35℃

Ambient temp. 35℃

Wind speed 2m/s

SUBJECT

Model WHP07600PSDPC9KQ SPECIFICATION PAGE：2/30

*.COP= Heating capacity (W)

Motor input (W)

*.Rated Capacity and input are measured with HITACHI inverter circuit by secondary Refrigerant

calorimeter Methods of JIS B8606 by SHANGHAI HIGHLY Electrical Appliances Co., Ltd.

Allowable capacity should be more than 95% of the rated capacity and allowable input

should be less than 107% of rated motor input.

2.6 Refrigerant R290

2.7 Displacement 30.7ml /rev

2.8 Allowable frequency range 900～7200 min-1

2.9 Oil HAF68 840±20ml

2.10 Allowable amount of refrigerant

charge

Below 800g

2.11 Compressor cooling Forced air

2.12 Hermetic Terminal

2.13 Space volume of inner case 1500cm3

2.14 Compressor weight 17.5kg incl. Oil

2.15 Motor Type

Insulation class

Direct current brushless motor E class

2.16 19.9Hz/21.7Hz/24.5Hz

3. THE PARAMETER OF MOTOR

Item Spec参数

explanation

3.1 Rotor Pole（Pole）4 ——

3.2 Rated Frequency Range（Hz）30-240

Electrical Frequency，Relating to

VDCmax of Inverter

3.3 Demagnetizing Current（A）54.01A Peak Current，at 120℃，-5%

Demagnetizing Rate

SUBJECT

SPECIFICATION

M od el W HP0 76 00 PS DPC 9K Q PAGE：3/30

Current 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

q5.44 5.39 5.34 5.29 5.24 5.18 5.12 5.06 5.00 4.95 4.89 4.83 4.78 4.72 4.66

d3.71 3.65 3.65 3.64 3.63 3.61 3.59 3.56 3.54 3.51 3.48 3.45 3.42 3.39 3.36

4. CHARACTERISTICS

4.1 Appearance

The surface of the compressor is painted to black, without obvious flaw ,impact scar, paint peel

off, rust and so on.

4.2. Indication

Compressor model type, manufacturing data are clearly indicated on the surface of compressor。

4.3. Residual moisture 150mg MAX

4.4. Residual impurities 90mg MAX

3.4 Inductance Ld（mH） Sheet 2 ——

3.5 Inductance Lq（mH）Sheet 2 ——

3.6 Stator coil resistance（20℃）（Ω）

0.502（20℃） line-to-line

3.7 Voltage Constant（Vrms/krpm）43.10V/krpm line-to-line

3.7 Torque Constant（N·m/Arms）0.69 Torque/Current

3.9 Inertia （Kg·m2）0.000666

3.10 Flux Φa（Wb）0.1702

φ(Per Phase，Peak)= 32 02f

3.11 Magnet Material NdFeB

Running effective value current（A）

3 4 5 6 7 8 9 10

Running torque（N.m）2.1 2.8 3.4 4.1 4.8 5.5 6.2 6.9

SUBJECT

SPECIFICATION

M od el W HP0 76 00 PS DPC 9K Q PAGE：4/30

5 PARTS AND DRAWING LIST

PARTS NAME QTY/SET DRAWING NO. REMARKS

Compressor 1 4CYCH**** Dimensioned sketch

Mounting

Parts

Rubber grommet

Bolt

Nut

4CYC00643

4CYC00700

Electrical

Parts

hermostat

erminal cover

Gasket

Nut

Rubber washer

Sleeve

4CYC01036

4CYC00988

4CYC01047

3CYC00004

4CYC00174

4CYC01042

4CYC01272

Lead routing

Pressure guarantee

Chart

Oil level datum

Notes for rotational

speed change

Performance curse

Appendix

*. Out of supply, for reference.

H EA T PU MP WA TE R HEA TE R CO MPR ES SO R CRI TE RI A

PAGE：5/30

COMPRESSOR CRITERIA

1 Strictly observe the specification

The compressor should be used in specifications written in this “compressor specification” and

not be used in specifications outside it.. The main circuit must link up with fuse or breaker.

2 Source voltage

Specified inverter is linked up with compressor terminals . Applied voltage of this inverter should

be voltage specified in this “compressor specification”. Alternating voltage should never be applied

on terminals (for example：commercial alternating voltage of 1φ100V,200V,3φ200V).This is because

that if applied alternating current the direct current motor will demagnetize.

3 Operating voltage range

The compressor should be operated in the range of rated voltage ±10% , under standard condition

and overload condition of rated frequency (applied voltage to inverter).It must be satisfied

with item 5 ,6,7.

4 Operating temperatures and pressures

The operating temperatures and pressures of a compressor should be within the range shown in

the table 2 and graph 1.

5Oil Back and height of the oil level

The oil should be returned continuously to the compressor and the structure of the refrigerating

system should not make oil stay in the system. The oil level in compressor should be satisfied

with chart 2.If not keep the oil level, the shortage will occur, and influence the reliability of

the compressor.(please check the oil level in the compressor with the sight glass which supplied

form SHEC.

H EA T PU MP WA TE R HEA TE R CO MPR ES SO R CRI TE

RI A PAGE：6/30

The compressor should be continuously oiled back, and there should be no oil storage part in the refrigeration system

configuration. Also, the oil level in the compressor should meet the conditions in Figure 2. However, when a foam state

occurs and the liquid becomes foamy, this portion does not belong to the oil level. If the oil level is not met, the oil supply

to the sliding part will be insufficient, which will seriously affect the reliability. (It can be confirmed by a compressor with

a sight glass for observing the oil level).

Thereshouldbe superheated gas returned to thecompressorunderall normal operatingconditions.

Table 2

Item Operating Envelope

Discharge pressure

MPa

3.13 {30.91}MAX

（condensing temperature :80℃）

（see graph 1）

Suction Pressure

MPa

0.168~0.95 {0.69~8.67}

(Evaporation Temperature ：-30℃~25℃)

Compressor case

bottom temp

99℃or below and 6 degrees

higher than condensing

temperature

Motor winding temp R.Voltage±10%: 120℃ MAX

Accumulator temp Higher than outlet pipe of evaporator

Ambient temp Meet for the condition of above mentioned motor winding temp.

H EA T PU MP WA TE R HEA TE R CO MPR ES SO R CRI TE RI A

PAGE：7/30

Graph 1 图 1

P1 P2 P3 P4 P5 P6 P7 P8

Condensing temperature 70℃25℃10℃10℃65℃80℃80℃80℃

Evaporation Temperature 25℃25℃10℃-30℃-30℃-10℃-5℃15℃

6 Current limitation

Current peak among motor terminals（include instantaneous current peak）should be

below demagnetizing current in order to prevent magnet in motor from demagnetization.

7 Pressure difference between suction and discharge

In all allowable rotational speed range, the difference of pressure should be more than

0.39MPa{4kgf/cm2}. But if there is no problem of noise when assembled in air conditioner,

it can also below this value.

HEAT PUMP WATER HEATER COMPRESSOR CRITERIA

PAGE：8/30

8 Discharge pipe temperature

Discharge pipe temperature is measured at a distance 300mm from the surface of compressor

and should be less than 110℃. The tip of the thermocouple is fixed by soldering when

measuring discharge pipe temperature .Furthermore, soldering point is covered with urethane

foam to prevent the effect of wind.

9 Dust of compressor hermetic terminals

Compressor hermetic terminals should be mounted with specified cover in right way to prevent

dust entering, and should be used in direction which dust is hard to enter in.

10 Lead wire of compressor hermetic terminals

Measuring the temperature of hermetic terminals , lead wire should be resist to the temperature

and be clamped so as not in touch with the surface of compressor and pipe.

11 Start-stop frequency

The frequency should be less than 6 times per hour. Operating time from start to stop should

be more than 3 minutes. Stopping time should be more than 3minutes.

12 Rate of rotational speed change

The rate of compressor rotational speed (acceleration) should be less than 133min-1/s, But if

The variable range is below 120min-1, rate can also be less than 600min-1/s when rotational

speed is reduced to avoid temporary over-current.

13 Air and moisture in refrigerating system

The degree of vacuum in refrigerating system should be less than 20Pa (150×10－3mmHg) at

room temperature just before charging refrigerant. The quantity of water should be less

than 0.15ml.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hitachi Compresseur d'air

Hitachi

Hitachi SRL Series Manuel utilisateur

Hitachi

Hitachi EC 710S Manuel utilisateur

Hitachi

Hitachi EC1110 Manuel de l'opérateur

Hitachi

Hitachi EC 79 Manuel de l'opérateur

Hitachi

Hitachi EC25E - Lon Wheelbarrow Air Compressor Manuel utilisateur

Hitachi

Hitachi EC 6C Manuel utilisateur

Hitachi

Hitachi EC 2510 E Manuel de l'opérateur

Hitachi

Hitachi Highly WHP09100VUKPA8LT6 Manuel utilisateur

Hitachi

Hitachi WHP09500AEDPC9EQ Manuel utilisateur

Hitachi

Hitachi Highly WHP05600VUKQA7JG6 Manuel utilisateur

Hitachi

Hitachi BEBICON SRL-5.5MB5A Manuel utilisateur

Hitachi

Hitachi EC 510 Manuel utilisateur

Hitachi

Hitachi EC 2610E Manuel de l'opérateur

Hitachi

Hitachi HIGHLY WHP08750VCDNC9AU Manuel utilisateur

Hitachi

Hitachi NEXT Series Manuel utilisateur

Hitachi

Hitachi Highly WHP07850VUK Manuel utilisateur

Hitachi

Hitachi EC6B Manuel utilisateur

Hitachi

Hitachi EC1433H Manuel utilisateur

Hitachi

Hitachi EC 10SB (SL) Instructions de montage

Hitachi

Hitachi Highly WHP13100AEDPC9EQ Manuel utilisateur

Hitachi

Hitachi EC 28M Manuel de l'opérateur

Hitachi

Hitachi EC 10SB (SL) Manuel de l'opérateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Hitachi

Hitachi CA47TLA-D2PE3 Manuel utilisateur

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur

Devair

Devair HDI-01 Manuel