Hioki 7015 Manuel utilisateur
SIGNAL SOURCE
OPERATION GUIDE
7015
1
――――――――――――――――――――――――――
―――――――――――――――――――――――
SOURCE FUNCTIONS
1. source DCCV function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV
(3) Press SHIFT to source standby mode
(4) Press MODE proper times to select 1.5V range or 15V
range
(5) Press or to select digit adjustment
(6) Press ▲or ▼to set the value of digit
(7) Press OUTPUT to output DCCV source
2. source DCCC function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CC
(3) Press SHIFT to source standby mode
(4) Press or to select digit adjustment
(5) Press ▲or ▼to set the value of digit
(6) Press OUTPUT to output DCCC source
3. source SCAN DCCV(DCCC) CONTINUOUS
function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select CONTINUE
(6) Press OUTPUT to output DCCV(DCCC) source
2
――――――――――――――――――――――――――
―――――――――――――――――――――――
4. source SCAN DCCV(DCCC) CYCLE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select CYCLE
(6) Press OUTPUT to output DCCV(DCCC) source
5. source SCAN DCCV(DCCC) STEP function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press proper times to select STEP
(6) Press OUTPUT to output DCCV(DCCC) source
(7) Press ▲or ▼to change STEP output
3
――――――――――――――――――――――――――
―――――――――――――――――――――――
6. source SCAN DCCV(DCCC) output
adjustment
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for SCAN (In case CV,
also choose 1.5V or 15V range)
(5) Press MODE again and hold 1 second
(6) Press MODE to cycle through STEP, TIME
INTERVAL and AMPLITUDE adjustments
(7) Press ▲or ▼to adjust STEP from 1 to 16 and
TIME INTERVAL from 0 to 99
(8) Press OUTPUT to save your setting
(9) Press MODE again and hold 1 second
7. source RAMP DCCV(DCCC) CONTINUOUS
function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press proper times to select CONTINUE
(6) Press OUTPUT to output DCCV(DCCC) source
4
――――――――――――――――――――――――――
―――――――――――――――――――――――
8. source RAMP DCCV(DCCC) CYCLE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press proper times to select CYCLE
(6) Press OUTPUT to output DCCV(DCCC) source
9. source RAMP DCCV(DCCC) output
adjustment
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to CV(CC)
(3) Press SHIFT to source standby mode
(4) Press MODE proper times for RAMP (In case CV, also
choose 1.5V or 15V range)
(5) Press MODE again and hold for 1 second
(6) Press MODE to cycle through POSITION,
RESOLUTION and AMPLITUDE adjustments
(7) Press ▲or ▼to adjust the RESOLUTION from 1 to
999
(8) Press OUTPUT to save your setting
(9) Press MODE again and hold 1 second
5
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
10. source PULSE function
(1) Set the slide switch to M/S position
(2) Rotate FUNCTION SWITCH from OFF to PULSE
(3) Press SHIFT to source standby mode
(4) Press ▲or ▼to select FREQUENCY
(5) Press MODE to display DUTY CYCLE
(6) Press ▲or ▼to adjust the DUTY CYCLE
(7) Press MODE to display PULSE WIDTH
(8) Press ▲or ▼to adjust the PULSE WIDTH
(9) Press MODE to display AMPLITUDE
(10) Press ▲or ▼to select the AMPLITUDE
(11) Press OUTPUT to output PULSE source
･Set SLIDE SWITCH to M/S position for source
functions
･The inside CIRCLE(FUNCTION) SWITCH labels
are for measurement functions
･The outside CIRCLE(FUNCTION) SWITCH labels
are for source functions
6
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
±1.5V ±15V SCAN
±1.5V
SCAN
±15V
SCAN
±1.5V
SCAN
±15V
±25mA SCAN
±25mA
SCAN
±25mA
Hz %ms Level
･In case FUNCTION SWITCH is at CV, Press
MODE to cycle through DCCV 1.5V range, DCCV
15V range, SCAN DCCV 1.5 range, SCAN DCCV
15V range, RAMP SCAN DCCV 1.5V range and
RAMP SCAN DCCV 15V range
･In case FUNCTION SWITCH is at CC, Press MODE to
cycle through DCCC 25mA range, SCAN DCCC 25mA
range and RAMP SCAN DCCC 25mA range
･In case FUNCTION SWITCH is at PULSE, Press
MODE to cycle through FREQUENCY(Hz),
DUTY CYCLE(%), PULSE WIDTH(ms) and
AMPLITUDE(V)
7
――――――――――――――――――――――――――
―――――――――――――――――――――――
NOTE
INTERVAL TIMESTEP AMPLITUDE
STEPS of
RESOLUTION
START
POSITION
START
AMPLITUDE(V)
STEPS of
RESOLUTION
END
POSITION
END
AMPLITUDE(V)
▲
▼
･In case source SCAN DCCV(DCCC) output
adjustment, Press MODE to cycle through
STEP(address), INTERVAL TIME(s) and
AMPLITUDE(V)
･In case source RAMP SCAN DCCV(DCCC) output
adjustment, Press MODE to cycle through START
POSITION, STEPS of RESOLUTION and START
AMPLITUDE(V)
In case you want to change END menu, Press ▲or ▼at
START POSITION then you can set STEPS of
RESOLUTION and END AMPLITUDE(V)
8
――――――――――――――――――――――――――
―――――――――――――――――――――――
MEASUREMENT FUNCTION
1. measurement DCV(ACV, ACDCV) function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to V or mV
(3) Press AC/DC to select DCV(ACV, ACDCV)
measurement
2. measurement DCA(ACA, ACDCA) function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to mA
(3) Press AC/DC to select DCA(ACA, ACDCA)
measurement
3. measurement OHM function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to Ω
(3) Press AC/DC for CONTINUITY
4. measurement TEMPERATURE function
(1) Set the slide switch to Mor M/S position
(2) Rotate FUNCTION SWITCH from OFF to mV
(3) Press REL (TEMP) and hold for 1 second to display
temperature
(4) Press DUAL to swap ℃and display
Table des matières
Autres manuels Hioki Instrument de mesure
Hioki
Hioki 3181-01 Manuel utilisateur
Hioki
Hioki LR8450 Manuel utilisateur
Hioki
Hioki CM4371-50 Manuel utilisateur
Hioki
Hioki CM4375 Manuel utilisateur
Hioki
Hioki 8846 Manuel utilisateur
Hioki
Hioki PW3390 Manuel utilisateur
Hioki
Hioki 3290 Manuel utilisateur
Hioki
Hioki FT6380 Manuel utilisateur
Hioki
Hioki 3287 Manuel utilisateur
Hioki
Hioki CM4141-50 Manuel utilisateur
Hioki
Hioki DT4281 Manuel utilisateur
Hioki
Hioki 9010 Manuel utilisateur
Hioki
Hioki SM7420 Manuel utilisateur
Hioki
Hioki 9132-50 Manuel utilisateur
Hioki
Hioki DM7275-01 Manuel utilisateur
Hioki
Hioki 3275 Manuel utilisateur
Hioki
Hioki IM3523A Manuel utilisateur
Hioki
Hioki LCR HiTESTER 3535 Manuel d'instructions
Hioki
Hioki 8730-10 Manuel utilisateur
Hioki
Hioki 8835-01 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur