Hioki 3275 Manuel utilisateur
INSTRUCTION MANUAL
3275
CLAMP ON PROBE
Contents
Introduction 1
Inspection 1
Notes on Safety 1
Notes on Use 4
Chapter 1 Overview 9
1.1 Product Overview 9
1.2 Features 9
1.3 Names of Parts 10
1.4 Parts of the Sensor 11
Chapter 2 Specifications 13
2.1 Product Specifications 13
2.2 Standards Applying 14
Chapter 3 Measurement Procedure 17
3.1 Notes on Use 17
3.2 Preparations for Measurement 20
3.3 Demagnetizing and Zero Adjustment 21
3.4 Measurement Procedure 22
1
___________________________________________________________________
___________________________________________________________________
WARNING This device is designed to comply with IEC 61010
Safety Standards, and has been thoroughly tested for
safety prior to shipment. However, mishandling
during use could result in injury or death, as well as
damage to the device. Be certain that you understand
the instructions and precautions in the manual before
use. We disclaim any responsibility for accidents or
injuries not resulting directly from device defects.
Introduction
Inspection
Notes on Safety
Thank you for purchasing this HIOKI 3275 CLAMP ON PROBE.
To obtain maximum performance from the device, please read this
manual first, and keep it handy for future reference.
When you receive the device, inspect it carefully to ensure that no
damage occurred during shipping. If damage is evident, or if it
fails to operate according to the specifications, contact your dealer
or Hioki representative.
Supplied accessories
Instruction manual 1
Carrying case 1
2
___________________________________________________________________
___________________________________________________________________
The symbol printed on the device indicates that the user
should refer to a corresponding topic in the manual
(marked with the symbol) before using the relevant
function.
In the manual, the symbol indicates particularly
important information that the user should read before
using the device.
Wear appropriate protective insulation (insulating rubber
gloves and boots, helmet and etc.) when connecting and
disconnecting from live electric circuits.
DANGER
Indicates that incorrect operation presents an extreme
hazard that could result in serious injury or death to the
user.
WARNING
Indicates that incorrect operation presents a significant
hazard that could result in serious injury or death to the
user.
CAUTION Indicates that incorrect operation presents a possibility of
injury to the user or damage to the device.
NOTE Indicates advisory items related to performance or correct
operation of the device.
Safety Symbols
This manual contains information and warnings essential for safe
operation of the device and for maintaining it in safe operating
condition. Before using the device, be sure to carefully read the
following safety notes.
The following symbols in this manual indicate the relative
importance of cautions and warnings.
3
___________________________________________________________________
___________________________________________________________________
Measurement categories (Overvoltage categories)
This device conforms to the safety requirements for CAT II
(600V), CAT III (300V) measurement instruments.
To ensure safe operation of measurement devices, IEC 61010
establishes safety standards for various electrical environments,
categorized as CAT I to CAT IV, and called measurement
categories. These are defined as follows.
CAT I: Secondary electrical circuits that are connected to a wall
outlet through a transformer or similar instrument.
CAT II: Primary electrical circuits in equipment connected to a
wall outlet via a power cord (portable tools, household
appliances, etc.)
CAT III: Primary electrical circuits of heavy equipment (fixed
installations) connected directly to the distribution panel,
and feeders between the distribution panel and outlets.
CAT IV: The circuit from the service drop to the service entrance,
then to the power meter and to the primary overcurrent
protection instrument.
Higher-numbered categories correspond to electrical environments
with greater momentary energy. So a measurement device
designed for CAT III environments can endure greater momentary
energythanadevicedesignedforCATII.
Using a measurement device in an environment designated with a
higher-numbered category than that for which the device is rated
could result in a severe accident, and must be carefully avoided.
Never use a CAT I measuring device in CAT II, III, or IV
environments.
The measurement categories comply with the Overvoltage
Categories of the IEC60664 Standards.
4
___________________________________________________________________
___________________________________________________________________
DANGER To avoid short circuits and potentially life-threatening
hazards, follow these precautions.
zNever attach the clamp to a circuit that operates at
more than the maximum rated voltage to earth.
zFor safety's sake, avoid clamping around bare
conductors, while clamping or measuring.
zWhile clamping and measuring, do not touch the
clamp in front of the barrier or the conductor being
measured.
zBe careful to avoid damaging the insulation surface
while taking measurements.
zThis device is made for use with the 3269 or 3272
POWER SUPPLY. It is possible to use a power
supply other than the 3269 or 3272, provided that
the connector and pin assignments match, and that
voltage and other electrical specifications are
satisfied. In the interest of safety, make sure that
the power supply has a protective earthing with
double-insulation construction.
zMake sure that the waveform measuring equipment
connected to this device's output terminal (BNC) is
equipped with a protective earthing with double-
insulation construction.
Notes on Use
Follow these precautions to ensure safe operation and to obtain
the full benefits of the various functions.
5
___________________________________________________________________
___________________________________________________________________
DANGER zIf the waveform measuring instrument being
connected to the output terminal (BNC) on this
device is equipped with any other measurement
terminals, take the following precautions to ensure
that the other instrument does not form a bridge
between the probe and any hazardous live of a
part.
1. Isolate the terminal to which the probe is
connected from other terminals on the measuring
instrument using basic insulation conforming to
the measurement category, working voltage, and
pollution degree requirements of the circuit being
tested.
2. If basic insulation requirements cannot be met
between the terminal to which this device is
connected and other terminals of the measuring
instrument, make sure that the voltage input to
the measurement terminal does not exceed the
Separated Extra-Low Voltage Earthed (SELV-E).
3. Read and observe all warnings and precautions
relating to electrical safety for the measuring
instrument being connected to the probe.
Refer to the following standards regarding the
meanings of underlined terms.
IEC 61010-1
IEC 61010-031
IEC 61010-2-032
6
___________________________________________________________________
___________________________________________________________________
DANGER zBe sure to observe all operating precautions for the
waveform monitoring instrument (oscilloscope or
recorder) and other measurement instruments to
which this device is connected
zWhen using a measurement instrument that does
not provide isolation between its input terminals
and chassis or other input terminals, please pay
attention to the following points.
If a signal is applied to an input terminal other than
that to which this device is connected, do not
connect the ground-side terminal to any non-
ground potential. Otherwise, short-circuit current
will flow through the 3269 or 3272, or this device
from the ground terminal, which could cause an
electrical accident or damage.
WARNING zDo not allow the device to get wet, and do not take
measurements with wet hands. This may cause an
electric shock.
Table des matières
Autres manuels Hioki Instrument de mesure
Hioki
Hioki 3470 Manuel utilisateur
Hioki
Hioki PQ3198 Manuel utilisateur
Hioki
Hioki SAFETY HiTESTER 3258 Manuel d'instructions
Hioki
Hioki 2331-20 Manuel utilisateur
Hioki
Hioki MR8740T Manuel d'instructions
Hioki
Hioki 8835-01 Manuel utilisateur
Hioki
Hioki RM2611 Manuel utilisateur
Hioki
Hioki MEMORY HiCORDER MR8870-20 Manuel utilisateur
Hioki
Hioki P9000-01 Manuel utilisateur
Hioki
Hioki MR8875 Manuel utilisateur
Hioki
Hioki 3196 Manuel utilisateur
Hioki
Hioki Super megohm SM7110 Manuel utilisateur
Hioki
Hioki PW3198 Manuel utilisateur
Hioki
Hioki 3332 Manuel utilisateur
Hioki
Hioki CM4002 Manuel utilisateur
Hioki
Hioki IM3533-01 Manuel d'utilisation et d'entretien
Hioki
Hioki FT3424 Manuel utilisateur
Hioki
Hioki TM6101 Manuel utilisateur
Hioki
Hioki 3664 Manuel utilisateur
Hioki
Hioki 2300 Smart Site Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur