HIK VISION Platinum Series Manuel utilisateur
IR Network Speed Dome
Quick Guide
IR High-Definition Network Speed Dome·Quick Guide
1
Thank you for purchasing our product. If there are any questions, or requests, please do
not hesitate to contact the dealer.
This manual applies to IR High-Definition Network speed dome.
This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new
version of this manual. We will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of
the security or signaling aspects of this product. UL has only tested for fire, shock or
casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or signaling aspects of this
product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
IR High-Definition Network Speed Dome·Quick Guide
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the EMC
Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
IR High-Definition Network Speed Dome·Quick Guide
3
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
All the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
Please use the power adapter, which is provided by normal company. The standard of
the power adapter is 24VAC10% or 12VDC10% (depending on models). The power
consumption cannot be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
Please make sure that the power has been disconnected before you wire, install or
dismantle the speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the speed dome yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire
or electrical shock will occur. The operating temperature should be -30°C ~ 65°C .
The dome cover for indoor use shall be kept from rain and moisture.
Warnings Follow these safeguards
to prevent serious injury or death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
IR High-Definition Network Speed Dome·Quick Guide
4
Exposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
Do not aim the speed dome at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
Please use the provided glove when open up the dome cover, avoid direct contact
with the dome cover, because the acidic sweat of the fingers may erode the surface
coating of the dome cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome
cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the speed dome to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the speed dome
and lead to additional costs.
Do not stare at infrared LED closely to avoid hurting your eyes when the infrared
lights are on.
IR High-Definition Network Speed Dome·Quick Guide
5
Table of Contents
1 Overview ..................................................................................................................6
2 Installation................................................................................................................7
3 Setting the Network Dome over the LAN.................................................................10
4 Accessing via Web Browser .....................................................................................13
IR High-Definition Network Speed Dome·Quick Guide
6
1Overview
Please make sure the power of the speed dome has been disconnected before
connecting the cables.
The cable interfaces of network speed dome are shown in following figure (left). The
cables are distinguished by different colors. The labels attached on the cables are for
identification.
Figure 1-1 Overview
Table 1-1 Overview
No.
Description
1
Network Cable
2
Audio Cable
3
Alarm Out
4
Alarm In
5
RS-485
6
Video Cable
7
Power Cable
8
SD Card Slot
Note: No. 8 is the SD card slot of the network speed dome. Remove the slot cover and
insert the SD card into the SD card slot, then install the slot cover back.
RED AC24V
YELLOW/GREEN
BLACK AC24V
YELLOW R485 -
ORANGE R485 +
VIEOD
1
2
3
4
6
5
7
SD CARD 8
IR High-Definition Network Speed Dome·Quick Guide
7
2Installation
Before you start:
Check the package contents and make sure that the device in the package is in good
condition and all the assembly parts are included.
Please make sure the wall is strong enough to withstand more than 8 times the
weight of the dome and the mount.
For cement wall, you need to use the expansion screw to fix the mount.
The long-arm wall mount is taken as the example for following mounting steps.
Note: Do not drag the speed dome with its waterproof cables as shown in Figure 1-1,
otherwise the waterproof performance is affected.
Figure 1-1 Do Not Drag the Cables
Steps:
1. Remove the protective sticker from the dome drive.
Figure 2-1 Protective Sticker
2. Drill 4 screw holes in the wall according to the holes of the mount.
3. Secure the wall mount to the wall with the M8 expansion screws.
Protective
Sticker
IR High-Definition Network Speed Dome·Quick Guide
8
Figure 2-2 Secure the Mount
Notes:
The mount in Figure 2-2 is the recommended mount for this series of speed dome,
and a pendent adapter is required if any other mount is selected. See Figure 2-3.
The dimension of pendant adapter is G11
2.
Figure 2-3 Pendent Adapter
4. Install the speed dome to the mount.
1). Hang the safety rope to the speed dome and then hook to the mount as shown in
Figure 2-4.
2). Route the cables of the speed dome through the wall mount.
3). Connect the corresponding video/audio/power/RS-485/alarm cables.
4). Loosen the two lock screws on the wall mount.
5). Install the speed dome to the mount, and secure the speed dome by rotating the
speed dome clockwise.
6). Secure the two lock screws with the Allen wrench.
Pendent
adapter
IR High-Definition Network Speed Dome·Quick Guide
9
Figure 2-4 Secure the Speed Dome
Safety Rope
Lock
Screw
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels HIK VISION Caméra de sécurité
HIK VISION
HIK VISION DS-2DF8A836IX-AEL Manuel utilisateur
HIK VISION
HIK VISION DS-2CD3021G0-I Manuel utilisateur
HIK VISION
HIK VISION AE-VC224T-IT Manuel utilisateur
HIK VISION
HIK VISION ECI-B62Z2 Manuel utilisateur
HIK VISION
HIK VISION iDS-TCR803-B Manuel utilisateur
HIK VISION
HIK VISION DS-2CE16C0T-IRF Manuel utilisateur
HIK VISION
HIK VISION DS-2CD852F Series Manuel utilisateur
HIK VISION
HIK VISION DS-2TXS2628-7P/QA/GLT/CH30S80 Manuel utilisateur
HIK VISION
HIK VISION DS-MH2211/32G Manuel utilisateur
HIK VISION
HIK VISION UD04334B Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2D21G0/M/NF Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2763G0-IZS Manuel utilisateur
HIK VISION
HIK VISION DS-2CD2D21G0/M-D/NF Manuel utilisateur
HIK VISION
HIK VISION DS-2CC11D3S-IR Manuel utilisateur
HIK VISION
HIK VISION U0T Series Manuel utilisateur
HIK VISION
HIK VISION UD07275B Manuel utilisateur
HIK VISION
HIK VISION THC-T129-PS Manuel utilisateur
HIK VISION
HIK VISION DS-2CD8153F-EWI Manuel utilisateur
HIK VISION
HIK VISION DS-2CD1T23G0-I Manuel utilisateur
HIK VISION
HIK VISION DS-2CD883F-EW series Manuel utilisateur
