HIK VISION ECI-T22Fx Manuel utilisateur

Network Turret Camera

ECI-T22Fx

Quick Start Guide

Appearance Description

This turret camera a earance is shown as the figures below.

Figure 1-1

Turret Camera Overview

Ty e Descri tion

Table 1-1

No. Description

1 Enclosure

2 Camera Body

3 Mounting Base

4 Power Cord

5 Network Cable

Note:

For cameras that su ort ower over Ethernet (PoE), the ower is assed along with data on

Ethernet cabling. A switch that su orts the PoE function is required.

Installation

Make sure of the following before you start:

●

The device included in the ackage is in good condition and all required arts are

included.

●

The standard ower su ly is 12 VDC or PoE (802.3af), and must be consistent with

camera requirements.

●

Equi ment is owered-off during installation.

●

The installation environment is correct.

●

The wall is strong enough to withstand four times the weight of the camera and bracket.

●

There are no reflective surfaces too close to the camera lens. The IR light from the

camera may reflect back into the lens and cause reflection.

Note:

Four camera ty es have the same installation method. We will use the III/IV turret camera as

an exam le to illustrate the installation.

Before you start:

Both wall and ceiling mounting are suitable for the turret camera. Ceiling mounting will be

used as an exam le for this section, and can be used as a reference for wall mounting.

Steps:

1. Paste the drill tem late (su lied) to the desired mounting osition on the ceiling.

2. Drill the screw holes and the cable hole in the ceiling according to the drill tem late.

Note:

Drill the cable hole if using the ceiling outlet to route the cable.

Φ85 mm

(3.35

)

Φ110 mm

(4.33

)

-Φ4.2 mm

(0.17

)

Screw Hole

Φ20 mm

(0.79

)

Figure 2-1 The Drill Tem late

3. Disassemble the camera.

1). Rotate the camera to align the notch with one of the marks.

2). Pry the mounting base with a flat object (e.g., a coin) to remove it from the camera

body.

Figure 2-2 Disassemble the Camera

4. Attach the mounting base to the ceiling with the su lied screws.

Notes:



The su lied screw ackage contains both self-ta ing screws and ex ansion bolts.



If the ceiling is made of cement, ex ansion bolts are required to fix the camera. If the

ceiling is made of wood, self-ta ing screws are required.

Figure 2-3 Fix the Mounting Base

5. Route the cables through the cable hole or side o ening.

6. Install the camera body back to the mounting base.

Figure 2-4 Install the Camera Body

7. Connect the ower cord and network cable.

8. Power the camera on, and set the network configuration (for details, refer to 3 Network

Camera LAN Configuration and 4 Access via Web Browser) to check whether the image is at

an o timum angle. If not, adjust the surveillance angle.

Pan: 0° to 360°

Tilt: 0° to 75° Rotation: 0° to 360°

Figure 2-5 Adjust Surveillance Angle

1). Hold the camera body and rotate the enclosure to adjust the an angle [0° to 360°].

2). Move the camera body u and down to adjust the tilt angle [0° to 75°].

3). Rotate the camera body to adjust the rotation angle [0° to 360°].

Network Camera LAN Configuration

Note:

The use of roducts with internet access carries inherent security risks. In order to avoid

network attacks and information leakage, strengthen your own network rotection.

If the roduct does not work ro erly, contact your dealer or the nearest service center for

hel .

3.1 Wiring

Connect the camera to the network as follows:

Network Cable

Network Camera

Computer

Connect Directly

Figure 3-1

Network Cable

Network Camera

Computer

Connect via a Switch or a Router

Figure 3-2

3.2 Activate t e Camera

Activate the camera by setting a strong assword. Activation via web browser, activation via

SADP, and activation via client software are su orted. Activation via SADP software and web

browser will be used as exam les to introduce camera activation.

Note:

Refer to the Network Camera User Manual for activation via client software.

3.2.1 Activation via Web Browser

Steps:

Power the camera on. Connect the camera to your com uter or the switch/router that

your com uter connects to.

In ut the IP address into the address bar of the Web browser, and ress Enter to enter the

activation interface.

Notes:



The camera’s default IP address is 192.168.1.64.



The com uter and the camera should belong to the same subnet.



For cameras that have DHCP enabled by default, use the SADP software to search for the

IP address.

Activation Interface (Web)

Figure 3-3

Create and in ut a assword.

STRONG PASSWORD RECOMMENDED – We highly recommend creating a strong

assword of your own choosing (using a minimum of eight characters, including

u er case letters, lower case letters, numbers, and s ecial characters) in order to

increase the security of your roduct. We recommend regularly resetting your

assword on a weekly or monthly basis, es ecially in high security systems.

Confirm the assword.

Click OK to save the assword and enter the live view interface.

3.2.2 Activation via SADP Software

SADP software is used for detecting online devices, activating cameras, and resetting

asswords.

SADP can be obtained from the su lied disk or the official website, and installed by

following the rom ts.

Follow the ste s to activate the camera.

Steps:

Run SADP to search for online devices.

Check the device status from the device list, and select the inactive device.

Select inactive device.

In ut and confirm

assword.

SADP Interface

Figure 3-4

Note:

SADP su orts batch camera activations. Refer to the SADP user manual for further details.

3. Create, in ut, and confirm the assword.

STRONG PASSWORD RECOMMENDED – We highly recommend creating a strong

assword of your own choosing (using a minimum of 8 characters, including u er

case letters, lower case letters, numbers, and s ecial characters) in order to

increase the security of your roduct. We recommend regularly resetting your

assword on a weekly or monthly basis, es ecially in high security systems.

Note:

You can enable the Hik-Connect service for the device during activation. Refer to Cha ter

5.1 for detailed information.

Click Activate to start activation.

You can check whether the activation is com lete in the o u window. If activation failed,

make sure that the assword meets the requirements, and try again.

Modify t e IP Address

3.3

Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the

network camera in the same subnet as your PC.

Use the SADP software or client software to search and change the IP address of the device.

IP Address modification via SADP software will be used as an exam le.

In order to modify the IP address via client software, refer to the user manual of the client

software.

Steps:

1. Run SADP.

2. Select an active device.

3. Change the device IP address to the same subnet as your com uter by either modifying

the IP address manually, or by checking the Enable DHCP checkbox.

Modify the IP Address

Figure 3-5

Note:

Hik-Connect can be enabled during activation. Refer to Cha ter 5.1 for detailed

information.

4. In ut the admin assword and click Modify to com lete IP address modification.

SADP su orts batch IP address modification. Refer to the SADP user manual for details.

Access via Web Browser

System Requirement:

O erating System: Microsoft Windows XP SP1 and above

CPU: 2.0 GHz or greater

RAM: 1 Gb or greater

Dis lay: 1024×768 resolution or higher

Web Browser: Internet Ex lorer 8.0 or higher, A le Safari 5.0.2 or higher, Mozilla Firefox 5.0

or higher, and Google Chrome 18 or higher

Steps:

1. O en the Web browser.

2. In the browser address bar, in ut the IP address of the network camera, and ress the

Enter key to enter the login interface.

Note:

The default IP address is 192.168.1.64. It is suggested that you change the IP address to the

same subnet as your com uter.

3. In ut the user name and assword.

The admin user should configure the device accounts and user/o erator ermissions

ro erly. Delete the unnecessary accounts and user/o erator ermissions.

Note:

The device IP address gets locked if the admin user erforms 7 failed assword attem ts (5

attem ts for the user/o erator).

4. Click Login.

Figure 4-1

5. Install the lug-in before viewing the live video and managing the camera. Follow the

installation rom ts to install the lug-in.

Note:

You may have to close the web browser to com lete lug-in installation.

Download Plug-in

Figure 4-2

6. Reo en the web browser after lug-in installation and re eat ste s 2 to 4 in order to login.

Note:

For further configuration instructions, lease refer to the network camera user manual.

Hik-Connect

Purpose:

Hik-Connect is a mobile a lication to view live camera images, receive alarm notifications,

etc.

Enable Hik-Connect for Use wit Cameras

5.1

Purpose:

Enable Hik-Connect should on your camera before using the service.

You can enable the service either via SADP software or a Web browser.

Enable Hik-Connect Service via SADP Software

5.2

Steps:

1. Check the Enable Hik-Connect checkbox:

1). For the “Activate the Device” age that a ears during camera activation, refer to

Cha ter 3.2.2.

2). For the “Modify Network Parameters” age that a ears while modifying the IP

address, refer to Cha ter 3.3.

2. Create or change the verification code.

Verification Code Setting (SADP)

Figure 5-1

Note:

The verification code is required when adding the camera to Hik-Connect.

3. Click and read the “Terms of Service” and “Privacy Policy.”

4. Confirm the settings.

Enable Hik-Connect via a Web Browser

5.2.1

Before You Start:

Activate the camera before enabling the service. Refer to Cha ter 3.2. for more information.

Steps:

1. Access the camera via the Web browser. Refer to Cha ter 4.

2. Enter the latform access configuration interface, as follows: Configuration > Network >

Advanced Settings > Platform Access.

Platform Access Configuration (Web)

Figure 5-2

3. Set the Platform Access Mode to Hik-Connect.

4. Check the Enable checkbox.

5. Click and read the “Terms of Service” and “Privacy Policy” in the o -u window.

6. Create or change the verification code for the camera.

Note:

A verification code is required when you add the camera to Hik-Connect.

7. Save the settings.

Add Camera to Hik-Connect

5.3

Before You Start:

Enable Hik-Connect on the camera before adding it to your Hik-Connect account. See

Cha ter 5.1.

Steps:

1. Use a network cable to connect camera to a router if the camera does not su ort Wi-Fi.

Figure 5-3 Connect a Router

Autres manuels pour ECI-T22Fx

Table des matières

Autres manuels HIK VISION Caméra de sécurité

HIK VISION

HIK VISION DS-2DT6232X-AELY Manuel utilisateur

HIK VISION

HIK VISION DS-2CD2532F-I Manuel utilisateur

HIK VISION

HIK VISION UD04363B Manuel utilisateur

HIK VISION

HIK VISION DS-2CD2063G0-I Manuel utilisateur

HIK VISION

HIK VISION TurboHD H0T Series Manuel utilisateur

HIK VISION

HIK VISION 26 series Manuel utilisateur

HIK VISION

HIK VISION TURBO HD DS-2CE5AC5T-AVPIT3Z Manuel utilisateur

HIK VISION

HIK VISION UD.6L0201B1015A01 Manuel utilisateur

HIK VISION

HIK VISION DS-2DY7236IX-A Manuel utilisateur

HIK VISION

HIK VISION UD04315B Manuel utilisateur

HIK VISION

HIK VISION E-series Manuel utilisateur

HIK VISION

HIK VISION DS-2XS6A25G0-I/CH20S40 Manuel utilisateur

HIK VISION

HIK VISION UD06820B Manuel utilisateur

HIK VISION

HIK VISION HiLook THC-B129-LPS Manuel utilisateur

HIK VISION

HIK VISION UD.6L0201D0151A01 Guide de l'utilisateur

HIK VISION

HIK VISION UD05331N Manuel utilisateur

HIK VISION

HIK VISION iDS-2CD9136-AIS Manuel utilisateur

HIK VISION

HIK VISION E-series Manuel utilisateur

HIK VISION

HIK VISION DS-2CD2D21G0/M/NF Manuel utilisateur

HIK VISION

HIK VISION DS-2XM6756FWD-IS Manuel utilisateur

HIK VISION

HIK VISION DS-2CC5197P-VPIR Manuel utilisateur

HIK VISION

HIK VISION HiLook IK-4142B-MH/W Manuel utilisateur

HIK VISION

HIK VISION DS-2AF1-513 Manuel utilisateur

HIK VISION

HIK VISION TurboHD H0T Series Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur