hestan KICS 36 Manuel utilisateur
INDOOR COOKING
Smart Induction Cooktop
KICS
Installation Manual
©2018 Hestan Commercial Corporation
EN
SAFETY DEFINITIONS
THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY OCCUR
AS A RESULT OF NOT OBSERVING THIS WARNING
THIS INDICATES THAT MINOR OR MODERATE INJURY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.
THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR
PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING THIS
WARNING.
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE INSTALLING OR
USING YOUR APPLIANCE TO REDUCE THE RISK OF FIRE, BURN HAZARD, OR OTHER
INJURY. KEEP THIS MANUAL FOR FUTURE REFERENCE.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
Installation and service must be performed by a qualified installer or service agency.
DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS
SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,
SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER
TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY
A QUALIFIED TECHNICIAN.
INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.
HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
©2018 Hestan Commercial Corporation
1
EN
When properly cared for, your Hestan appliance will provide safe, reliable service for many years.
When using this appliance, basic safety practices must be followed as outlined below.
IMPORTANT: Save these instructions for the local electrical inspector’s use.
INSTALLER: Please leave these Installation Instructions with the owner.
OWNER: Please retain these Installation Instructions for future reference.
Do NOT install this appliance outdoors.
SAFETY PRECAUTIONS - BEFORE YOU BEGIN
ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing appliance. Failure to do so
can result in death or electrical shock.
ELECTRICAL GROUNDING
This appliance must be grounded. Grounding reduces the risk of electric shock in the event of
a short circuit. Read the ELECTRICAL CONNECTIONS section of this manual for complete
instructions.
DO NOT ground to a gas pipe.
DO NOT use an extension cord with this appliance.
DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL or
GROUNDING circuit could result in an electrical shock.
TABLE OF CONTENTS
1 SAFETY PRECAUTIONS - BEFORE YOU BEGIN
2 MODEL NUMBERS
2 RATING LABEL
2 REGULATORY / CODE REQUIREMENTS
3 CUTOUT DIMENSIONS AND REQUIREMENTS
6 COOKTOP INSTALLATION
8 ELECTRICAL CONNECTIONS
11 FINAL SETUP
12 PARTS LIST
12 SERVICE
©2018 Hestan Commercial Corporation
2
EN
MODEL NUMBERS
RATING LABEL
The rating label contains important information about your Hestan appliance such as the model
and serial number, electrical rating and the minimum installation clearances.
The rating label is located on the bottom of the cooktop.
If service is necessary, contact Hestan Customer Service with the model and serial number
information shown on the label.
COOKTOP MODELS
MODEL NO. DESCRIPTION CIRCUIT BREAKER
REQUIRED
KICS 36 36” Smart Induction Cooktop 50 Amp
REGULATORY / CODE REQUIREMENTS
Installation of this cooking appliance must be made in accordance with local codes. In the
absence of local codes, this unit should be installed in accordance with the National Electrical
Code and local codes.
This appliance must be electrically grounded in accordance with local codes or in the absence of
local codes with the National Electrical Code
ANSI/NFPA 70
, or Canadian Electrical code
CSA
C22.1
.
Rating label
Figure 1. Typical rating label
©2018 Hestan Commercial Corporation
3
EN
CUTOUT DIMENSIONS AND REQUIREMENTS
CABINET REQUIREMENTS
To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage units
located above the surface units should be avoided. If cabinet storage is to be provided, the risk can
be reduced by installing a range hood that projects horizontally a minimum of 5 inches [ 12.7 cm]
beyond the bottom of the cabinets.
Model A B C
36” [91.4cm] 30” [76.2 cm] min. or as
required by ventilation hood. * 18” [45.7 cm] min height
from counter-top to nearest
cabinet on side of unit. *
36” [91.4 cm]
min.
Model D E
36” [91.4cm] 2” [5.1 cm] min clearance from
cutout to side wall on the left
or right of the unit. **
13” [33 cm] depth of
unprotected overhead
cabinets.
* 30” [76.2 cm] minimum clearance between the top of the cooking surface and the bottom of an
unprotected wood or metal cabinet.
** It is permissible to mount the cooktop as close as 2” away from a cabinet or wall on one side.
The other side must be unobstructed.
B
A
C
D
E
WALL COVERING, CABINETS,
AND COUNTERTOP MUST
WITHSTAND HEAT UP TO
212° F [100° C]
Figure 2. Cabinet clearances
©2018 Hestan Commercial Corporation
4
EN
CUTOUT DIMENSIONS AND REQUIREMENTS
(CONT.)
BEFORE YOU START
Do not install the cooktop above an unventilated oven or a dishwasher.
The cooktop is 2 1/8” deep, and requires a minimum 1” clearance below it.
If a drawer is directly below the cooktop, it and its contents must be heat resistant. Such a
drawer should be placed/arranged so that nothing can be drawn from the drawer into the
ventilation fans of the cooktop.
IMPORTANT PREPARATION SUGGESTIONS
Chamfer all exposed edges of decorative laminate to prevent damage from chipping.
Radius corners of cutout and file to ensure smooth edges and prevent corner cracking. A 1/4” or
3/8” diameter drilled hole at each corner to start the cut is recommended.
Rough edges, inside corners which have not been rounded and forced fits can contribute to
cracking of the countertop laminate.
If the countertop material is susceptible to moisture, the cut edges should be sealed with a
suitable sealer. All materials and adhesives must be able to withstand temperatures up to 212F
[100C].
The junction box must be accessible with the cooktop in place.
For service purposes it is advisable to have enough access to the bottom of the cooktop so that
it can be lifted out.
©2018 Hestan Commercial Corporation
5
EN
CUTOUT DIMENSIONS AND REQUIREMENTS
(CONT.)
Figure 3. Cooktop dimensions
36 ⁄”
[929 mm]
22 ⁄”
[573 mm]
2 ⁄”
[46.5 mm]
3/8”
[10 mm]
2” [5.1 cm]
MIN CLEARANCE
3 ⁄” [7.9 cm]
min depth
HOLE FOR
POWER CABLE
ENCLOSURE
BOTTOM
(OPTIONAL)
34 ¼
[87 cm] 19-¼” [48.9 cm]
Figure 4. Cutout dimensions
©2018 Hestan Commercial Corporation
6
EN
COOKTOP INSTALLATION
Always consult the countertop manufacturer for specific instructions.
Ensure the countertop is square and level and ensure no structural members interfere with
space requirements.
Prepare the cutout according to the instructions (see cutout dimensions).
Make sure the wall coverings, countertop and cabinets around the cooktop can withstand heat
(up to 212° F / 100°C).
STEP 1
Remove packaging materials and literature package from the cooktop before beginning
installation. Remove Installation Manual from literature pack and read them carefully before
you begin.
EXCESSIVE WEIGHT HAZARD
Use two or more people to move and install cooktop. Failure to do so can result in back or
other injury.
CUT HAZARD
Beware of sharp edges. Wear protective gloves or use the polystyrene ends when carrying the
product. Failure to use caution could result in minor injury or cuts.
Figure 5. Needed tools
COOKTOP HOUSING
TOWEL OR CLOTH
Figure 6. Protecting the surface
©2018 Hestan Commercial Corporation
7
EN
COOKTOP INSTALLATION
(CONT.)
STEP 2
Place a towel or cloth on the work surface. Place the cooktop face down on the protected area.
Step 3
A foam tape is provided to seal the cooktop to the countertop. Apply tape to the underside of the
cooktop glass between the body of the cooktop and the inner edge of the frame.
There should be about .08” [2mm] between the edge of the tape and the edge of the glass. Use tape
around the entire glass perimeter.
The tape will retain the cooktop and seal against leaks into the cabinet. Trim the tape ends so that
they meet with no gaps.
STEP 4
Make a final check that all required clearances are met.
Feed the cable through the cabinet as needed. Insert the cooktop centered into the cutout opening.
Make sure the front edge of the counter top is parallel to the cooktop.
COOKTOP HOUSING
FOAM
TAPE
COOKTOP GLASS
GLASS FRAME
2 mm
Figure 7. Apply foam tape
Figure 8. Placing cooktop
©2018 Hestan Commercial Corporation
8
EN
COOKTOP INSTALLATION
(CONT.)
Use the countertop opening dimensions that are given with these instructions.
The cooktop may be installed over a single oven. The oven must exhaust out of the cooktop
enclosure.
The cooktop should be centered over the oven.
The cooktop and the oven must be installed according to each specific installation instruction.
ELECTRICAL CONNECTIONS
B
A
JUNCTION BOX LOCATION
The ELECTRICAL CONDUIT is 4 1/2 FEET
LONG.
The junction box must be located where it
will allow considerable slack in the conduit
for serviceability.
A: Place junction box so that the conduit
will easily reach it. Make sure that the
conduit will clear any drawers or other
obstructions.
B: Install junction box so that it can be
reached through the front of the
cabinet.
Figure 9. Location of electrical connection
Autres manuels pour KICS 36
1
Table des matières
Langues :
Autres manuels hestan plaque de cuisson
hestan
hestan KGC Series Manuel utilisateur
hestan
hestan KBGIT Manuel utilisateur
hestan
hestan KIC Manuel utilisateur
hestan
hestan KICS 36 Manuel utilisateur
hestan
hestan KIC series Manuel utilisateur
hestan
hestan KEC 30 Manuel utilisateur
hestan
hestan KGC30-NG Manuel utilisateur
hestan
hestan KEC series Manuel utilisateur
hestan
hestan KICS30 Manuel utilisateur
hestan
hestan KIC 30 Manuel utilisateur
