HESHBON HO-250A Manuel d'instructions
Installation/Operation & Maintenance Manual
Please read this manual carefullybefore operation.
You must read and understand the precautions for safety
and avoid any damages and injury.
Fully Automatic A.T.F Changer
HO-250A
Installation/Operation & Maintenance Manual
1. Introduction
1-1. Features and characteristics
1-2. Names of each part
1-3. Description
1-4. Specification
1
1
2
3
4
2. Safety
2-1. Danger/Warning/Caution
5
5
3. Operation
3-1. Check points before operation
3-2. Calibration
3-3. Operation
7
7
7
8
4. Maintenance
4-1. Trouble-Shooting
5. Sparepart List
11
11
TABLE OF CONTENTS
▶This manual was prepared in January 2017 the product specifications
contained in this manual are subject to change without notice.
1
1-1.
Features and characteristics
DIGITAL
DIGITAL
DIGITAL
Possible to work for 4-10 shift
transmission
Exchanging level gauge Mode
Possible to work for car type without
level gauge
Voice guidance Mode
One-touch oil line
change Mode
Input car data
Etc.
•Equiped electronic digital scale
•Oil saving Mode
(Some of car type are excluded)
•Installed oil exchange program on cooler line
•Display oil temperature
•Possible transmission flushing by chemical
•Used oil sampling function (Application of selected model)
•Installed 40L used oil tank
•Installed anti-overflowing sensor of used oil
Introduction
2
Introduction
1-2.
Description
① Exchanging level gauge Mode ⑩ Up button
④ Recovery used oil In the vehicle
set amount ⑬ Pause button
⑦ Possible transmission flushing
by chemical ⑯ Menu button
② Exchanging IN/OUT Cooler line ⑪ Down button
⑤ inject new oil In the vehicle set
amount ⑭ Stop button
⑧ Recovery : Recovery of waste oil into the
device in a vehicle.
(It works only when pressing the start button)
⑰ Line change(option) : Change
Injection and recovery hose lines.
③ Oil saving Mode : 0.1 liters of used oil
recovery and inject new oil, so you let
healing the least. (Except for some models) ⑫ Start button
⑥ Drain the used oil. ⑮ Calibration the scale.
⑨
Inject : Inject of new oil into the device in
a vehicle.
(It works only when pressing the start button)
⑱ FUNC : System settings
⑲ ENTER button
Only trained personnel may
operate the equipment.
Inexperience can cause
accidents.
Work only on the horizontal
place for safety purpose.
3
Safety
2-1.
Danger / Warning / Caution
Danger / Warning/ Caution
Make sure you follow the instructions, otherwise critical injury or death can occur.
Make sure you follow the instructions, otherwise critical injury or damage can occur.
Make sure you follow the instructions; otherwise, injury or damage can occur
The terms are described to enhance the understanding of the equipment.
Danger / Warning / Caution
Model No. HO-250A
Control type Computer control
Measurement Digital scale control
Motor 0.2kw 1PH 220V
Pump Type TRO CHOID Relief Auto
New oil tank 20ℓ
Used oil tank 40ℓ
Net weight Approx. 50kg
Dimension 530(W) x 595(L) x 900(H)mm
1-3. Specification
Do not touch power cord with
wet hands.
▶ It may cause injuries or even
death.
Do not use damaged
power plug or loosened
outlet.
▶ It may cause injuries or
even death.
Do not expose this product
directly to rain and moisture.
▶It may cause injuries or even
death.
Do not work with this product
close to heating source.
▶It may cause injuries or even
death.
Do not apply excessive
force to unplug power
cord.
▶ It may cause an electric
shock or a fire.
Make sure to install
it indoors only and protect it
from rain or snow.
Do not insert multiple plugs
on the socket.
▶ It may cause an electric
shock or a fire.
Make sure that electric oulet/
pins must be
maintained clean.
▶ It may cause an electric
shock or a fire.
Do not apply any impact
on the body frame[housing]
or expose it to dust.
▶It may cause unexpected
malfunction.
Do not expose this product
to direct sun light.
▶ It may cause unexpected
malfunction.
Do not attempt to push any
incorrect button during
operation.
▶ It may cause unexpected
malfunction
Do not modify the control
panel and structure volun-
tarily.
▶ It may cause unexpected
malfunction.
Make sure to install
it indoors only and protect
it from rain or snow.
Read this manual carefully
before use.
▶ Serious accidents may
happen due to negligence of
danger & warning information.
Do not use unprescribed
oil.
▶ It can cause damage to
the machine.
Do not bend the power
cord or place any heavy
article on it.
4
Safety
Make sure that you read and understand them.
Operation
3-1. Preparing to work
3-2. How to calibration new oil Scale
(1) Fill up new oil in the new oil tank.
(2) Connect power supply and turn on the power switch.
(3) FWD vehicle shift the gear into N and RWD vehicle shift the gear
into P.
(4) Connect coupler to recovery hose and injection hose.
(5) Make sure oil flow direction is upward(⇡) in the sight glass.
(6) If oil flow direction is downward(), switch line change lever.
Then oil flow direction will be changed to upward.
1-1) Put 20 liter empty oil tank on the electronic scale.
1-2) Connect the oil inlet hose.
1-3) Press the calibration button.
1-4) Press DOWN button and hold (3sec) until COMPLETE message
shown on the screen.
1-5) Make sure the process is completed.
2-1) Put 20 liter full oil tank on the electronic scale.
2-2) Connect the oil inlet hose.
2-3) Press the calibration button.
2-4) Press UP button and hold (3sec) until COMPLETE message shown
on the screen.
2-5) Make sure the process is completed.
1) Calibration with 20 liter empty oil tank
2) Calibration with 20 liter full oil tank.
▶ Park vehicle on the flat floor and make sure the vehicle is securely
braked.
(*If necessary, prop up wheels to prevent rolling the wheel.)
▶ Operator should wear safety glasses and protective equipment.
▶ Precise electronic scale equipped in the product, so pay attention to
prevent damage from impact or shock.
CALIBRATION
UP = 20 liter
DOWN = 0 liter
5
6
Operation
3-3. How to Use
1) Insert the hose to the oil check gauge of the vehicle.
2) Connect the appropriate accessories in the vehicle.
(Accessories for level gauge)
3) Connect a hose on any device orientation.
4) Select the level gauge mode(AUTO1).
5) Use the ▲ ▼ buttons to set the amount of oil changes. (Initial value 8.0 liters)
6) Press the Start button.
7) If necessary after checking whether the end-of-job message comes up oil
level is potent using a setting recovery, setting injection and align the oil level.
8) Finish the work.
1) Remove the cooling line of the vehicle.
2) Connect the appropriate accessories in the vehicle.
3) Connect a hose on any device orientation.
4) Check the oil flow direction. (The normal flow is flowing over, under it.) ⇡
5) Switch the direction lever to replace the line if the oil flow direction does not
match.
6) AUTO2 Select the exchanging cooler line mode.
7) Use ▲ ▼ to set the amount of oil changes. (Initial value 8.0 liters)
8) Press the Start button.
9) If necessary after checking whether the end-of-job message comes up oil
level is potent using a setting recovery, setting injection and align the oil level.
10) Finish the work.
AUTO_1
volume: 8.0 0.0
0.0
(1) Exchanging level gauge mode
(2) Exchanging cooler line mode
AUTO_2
volume: 8.0 0.0
0.0
7
Operation
1) Select
Setting recovery or Setting injection
.
2) Use the ▲ ▼ buttons to set.
3) Press Start button.
RECOVERY
volume: 1.0 0.0
0.0
CHARGE
volume: 1.0 0.0
0.0
(4)
Setting recovery / Setting injection
1) Remove the cooling line of the vehicle.
2) Connect the appropriate accessories in the vehicle.
3) Connect a hose on any device orientation.
4) Check the oil flow direction. (The normal flow is flowing over, under it.) ⇡
5) Switch the direction lever to replace the line if the oil flow direction does not match.
6) AUTO3 Select the oil saving mode.
7) Use ▲ ▼ to set the amount of oil changes. (Initial value 8.0 liters)
8) Press the Start button.
9) If necessary after checking whether the end-of-job message comes up oil
level is potent using a setting recovery, setting injection and align the oil level.
10) Finish the work.
(3) Oil saving Mode
AUTO_3
volume: 8.0 0.0
0.0
8
Operation
1) Standby : Display oil temperature, new oil and
used oil.
2) Manual Recovery : Only works if press the
START button
3) Manual Injection : Only works if press the
START button
4) Cleaning mode : After chemical Injection,
setting UP/DOWN buttons and
START button to begin
1) Pull the exchange lever forward.
2) Connect the hose accessories at the end of Injection hose (red).
3) Press the discharge used oil button.
4) Press the Start button.
5) Check that the discharge through an Injection hose.
DISCHARGE
volume: 5.4 0.0
CLEANING
5 minute
CHARGE
volume: 0.0
RECOVERY
volume: 0.0
(5) Discharge used oil
(6) Other information Description
NEW : 0.0 L
USED : 0.0 L
TEMPERATURE
: 00℃
Table des matières
