Herd KW01 Manuel utilisateur
1
Installation Guide
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: KW03-IG
Rev: A
Date: 19-Mar-19
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
This Guide is for all Truck Guard
Models, including (where
applicable):
Aero
Defender
Texas
Big Texas
Road Train
Super Road Train
Important
•Herd Truck Guards are vehicle "Make & Model" specific. Use of a Truck Guard on a vehicle other than the
model it was designed for will constitute improper use of the product and may void warranty.
•Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these
instructions, OEM hardware means the truck's original factory hardware.
•For further detail of warranty coverage and warranty repair information visit www.HERD.com.
Truck I.D.
Truck Models
KW01
Kenworth W900L -
SFA
General Safety
•Take time to fully read the instructions before installing the Herd Truck Guard.
•At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.
•Parts and components of the Herd Truck Guard can be heavy, handle with care to avoid injuries.
•Respect power tools and use them as advertised.
For assistance call
1-888-543-4373
www.HERD.com
Thank you for choosing HERD!
HERD North America Inc.
2168 Springfield Road
Box 28, Group 525, RR5
Sunnyside, MB Canada R5R 0J3
Reference this Parts List if your Truck Guard has a CEB (Captive Eye Bolt) Latching System
2
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: KW03-IG
Rev: A
Date: 19-Mar-19
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
Figure 1 –Captive Eye Bolt Latching System
Table 1: Parts and Hardware Included
Items marked with * are not shown in Figure 1 above
Item No
Part No
Description
Qty
1
BR-KW01-AT (Only with Aero, Road Train, Super Road
Train, Texas, & Big Texas Versions)
or
BR-KW01-FLT (Only with Defender Version)
BRACKET, Kenworth W900L - SFA
1
2
1MPA027 (Only with Aero, Road Train, Super Road
Train, Texas, & Big Texas Versions)
or
1MPA024 (Only with Defender Version)
ASSY - LEGACY LIFT ASSIST
2
3
7-EYEBOLT KIT
CAPTIVE EYEBOLT ASSEMBLY
2
5
HERD TRUCK GUARD
TRUCK GUARD APPEARANCE MAY VARY BY SKU
1
6
1-MP-KW01.60
MOUNTING ASSEMBLY, TOW EYE, KW01
2
*7
500088
BOLT-HEX 1/2-13X2-1/2 NC GR8 YZP
6
*8
500167
NUT-NYLOCK 1/2-13 NC GR8 YZP
6
*9
500206
WASHER-FLAT 1/2 SAE GR8 YZP
12
*10
500172
NUT-NYLOCK 3/4-10 NC GR8 YZP
2
*11
500211
WASHER-FLAT 3/4 SAE GR8 YZP
2
5
3
2
1
6
Reference this Parts List if your Truck Guard has a Slam Latch Latching System
3
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
Figure 2 –Slam Latch Latching System
Table 2: Parts and Hardware Included
Items marked with * are not shown in Figure 2 above
Item No
Part No
Description
Qty
1
BR-KW01-AT-SL (Only with Aero, Road Train, Super Road
Train, Texas, & Big Texas Versions)
or
BR-KW01-FLT-SL (Only with Defender Version)
BRACKET, Kenworth W900L - SFA
1
2
1MPA027 (Only with Aero, Road Train, Super Road Train,
Texas, & Big Texas Versions)
or
1MPA024 (Only with Defender Version)
ASSY - LEGACY LIFT ASSIST
2
4
4-MC-SLA-A
ASSY- LEGACY SLAM LATCH
1
5
HERD TRUCK GUARD
TRUCK GUARD APPEARANCE MAY VARY BY SKU
1
6
1-MP-KW01.60
MOUNTING ASSEMBLY, TOW EYE, KW01
2
*7
500088
BOLT-HEX 1/2-13X2-1/2 NC GR8 YZP
6
*8
500167
NUT-NYLOCK 1/2-13 NC GR8 YZP
6
*9
500206
WASHER-FLAT 1/2 SAE GR8 YZP
12
*10
500172
NUT-NYLOCK 3/4-10 NC GR8 YZP
2
*11
500211
WASHER-FLAT 3/4 SAE GR8 YZP
2
5
2
1
4
6
Installation Procedure
4
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
1. Remove the 6 OEM bolts on the
front of the OEM bumper. Retain
factory hardware. Disconnect
OEM driving lights if applicable.
Remove the OEM bumper. If
factory center tow pin is an
option on the truck, remove it as
well. If the truck has a collision
mitigation radar sensor, unplug
and remove it.
Figure 3 –OEM Bumper Removal Front View
2. Insert tow receiver inserts
(Item 6) into the tow receivers
on both passenger and driver
sides.
Secure in place using OEM
clevis pin.
Figure 4 –Tow Receiver Insert Installation
Remove & Retain 6 Bolts
6
Installation Procedure
5
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
3. Install Herd steel bracket
(Item 1) to truck using supplied
1/2”hardware (Items 7, 8, 9).
Be sure all 6 mounting points are
used and that the supplied
packers (Part of Item 1) are used
on the innermost 2 mounting
points.
The ¾” threaded rod portion of
the tow receiver insert (Item 6)
will pass through the backplate of
the bracket and be fastened
down in step 4.
Note:
If installer has a crane available,
truck guard can be attached onto
truck with bracket, otherwise
disassemble truck guard from
bracket first. Keep hardware. If
bumper is equipped with lift
assist, the springs must be
removed. Refer to instructions
S004 (Defender bumpers) or S005
(Aero/Texas bumpers) for proper
lift assist disassembly procedure.
Figure 5 –HERD Bracket Installation (Driver Side Shown)
Use Packers
1
Installation Procedure
6
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
4. Tighten 3/4" nut and washer
(Items 10, 11) onto threaded end
of the tow receiver inserts
(Item 6) to 70-80 ft-lbs. Do not
overtighten.
Figure 6 –HERD Bracket Installation (Driver Side Shown)
1
11
10
6
Installation Procedure
7
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
5. If the Herd Truck Guard was
disassembled from bracket in
step 3, reinstall Herd Truck Guard
onto bracket using the hardware
kept from step 3.
For DFLT & Defender models
only: To install the hinge bolts,
the bumper must be in the open
(down) position to allow the
bottom lip to go under and
around the steel hinge.
Figure 7 –View of Bracket Hinge
6. Close the truck guard and check
fitment. Truck guard position can
be adjusted side to side and up or
down as required. Once fitment
is confirmed, tighten all mounting
bolts. Torque 3/4” hardware to
75lb-ft. Torque 1/2” and 5/8”
hardware to 110lb-ft.
Figure 8 –Herd Truck Guard Installed
Installation Procedure
8
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
Important
•Check mounting points after the first 5000 km and every 3-6 months.
•If this truck guard is equipped with Legacy Herd Slam Latch, periodic adjustment is required. Refer to Legacy
Slam Latch Installation adjustment instructions to properly adjust your Slam Latch.
•The drop-forged eyebolts are an integral part of the strength of Herd Truck Guards. When tightened firmly,
they will minimize vibration and provide superior impact resistance.
•To help maintain the factory finish, avoid acid wash.
Installation Procedure
9
Part No: KW01-LEGACY-IG
Rev: B
Date: 2019-06-24
1-888-543-4373
www.HERD.com
1-888-543-4373
Autres manuels Herd Accessoires automobiles
Herd
Herd Aero Series Manuel utilisateur
Herd
Herd 404006 Manuel utilisateur
Herd
Herd SLAM LATCH Mode d’emploi
Herd
Herd PB11C4-02 Manuel utilisateur
Herd
Herd MK15C4-02 Manuel utilisateur
Herd
Herd IN24A2 Manuel utilisateur
Herd
Herd Aero Manuel utilisateur
Herd
Herd Aero Manuel utilisateur
Herd
Herd C4 Series Manuel utilisateur
Herd
Herd FL33BG Manuel utilisateur
