Heatcon! WG Manuel utilisateur

Installation guide

heatcon! System WG

0450000600-1915

heatcon! System

Installation guide

Edition: 04.2019

Art:0450000600-1915

We reserve the right to make technical and content changes to this document at all times without prior notice.

EbV assumes no responsibility for any errors or omissions in this document.

All rights to this document and the contained the contained themes and figures are reserved. Reproduction, disclosure to third parties or use of

the content, either in whole or in part, is forbidden without the prior written consent of EbV.

1Table of contents

1TABLE OF CONTENTS........................................................................................................................................... 3

2SAFETY................................................................................................................................................................ 4

2.1 GENERAL INFORMATION............................................................................................................................................4

2.2 STRUCTURE OF THE WARNING INSTRUCTIONS ................................................................................................................ 4

2.3 PERSONNEL QUALIFICATIONS......................................................................................................................................4

2.4 THE HOUSING HEATCON WG ..................................................................................................................................... 5

3HEATCON! WG .................................................................................................................................................... 5

4INSTALLATION..................................................................................................................................................... 5

5SUPPLY LINE AT THE HEATCON! WG.................................................................................................................... 6

6CONNECTION TERMINALS................................................................................................................................... 6

7INSTALLATION (PARAMETERIZATION) HEATCON! EC .......................................................................................... 6

7.1 INSTALLATION VIA MMI............................................................................................................................................ 6

7.2 INSTALLATION VIA COMPUTER/LAPTOP ........................................................................................................................7

7.2.1 Preparation ................................................................................................................................................. 7

7.2.2 Installation .................................................................................................................................................. 8

8FINISHING ........................................................................................................................................................... 8

2Safety

2.1 General Information

Any person charged with working on the device or system, must have read and understood this manual, especially the

chapter on “Safety”.

Instruction may be necessary, dependent on the professional qualifications of the persons in question.

The relevant accident prevention regulations and other generally accepted safety regulations must be complied with.

2.2 Structure of the warning instructions

Explanation of the warning instructions in this manual:

DANGER

Brief description of the hazard

The signal word DANGER indicates a directly threatening hazard.

Non-observation leads to severe injuries or death.

WARNING

Brief description of the hazard

The signal word WARNING indicates a possible hazard.

Non-observation may result in severe injuries or death.

CAUTION

Brief description of the hazard

The signal word CAUTION indicates a possible hazard.

Non-observation can result in slight or moderate injuries.

ATTENTION

Brief description

The signal word Attention indicates possible property damage.

Non-observation can lead to damage to the device or plant.

NOTE

The signal word note indicates further information about the device or its use.

2.3 Personnel qualifications

The electrical installation, initial operation and servicing of the device may only be performed by qualified electrical

technicians who have been authorised by the operator.

The technicians must have read and understood these operating instructions and follow their procedures.

Requirements to be met by a qualified electrical technician:

•Knowledge of general and special safety and accident prevention regulations.

•Knowledge of the relevant electrical regulations (e.g. DIN VDE 0100 Part 600, DIN VDE 0100-722) plus the

relevant national regulations.

•Ability to identify risks and avoid possible hazards.

2.4 The housing heatcon WG

The wall mounting housing heatcon! WG is intended for indoor installation and must not be installed outdoors.

Bevor installation and during use the housing must be checked for damage and thightness and replaced by a specialist

if necessary.

3heatcon! WG

heatcon! WG is a complete set consisting of

- Wall-mounted housing WG 1000

- heatcon! EC 1321 Pro

- heatcon! MMI 200

heatcon! EC and MMI 200 are mounted in the wall-mounted housing. All inputs and outputs of the heatcon! EC are

already wired to the terminals. The installation is carried out comfortably at the easily accessible terminals of the wall

mounting housing.

4Installation

Montieren Sie das Wandaufbaugehäuse an geeigneter Stelle an der Wand. Zur Montage können Sie wahlweise eine

Hutschiene EN 60715 (nicht im Lieferumfang enthalten) verwenden oder die mitgelieferten Wandhalter.

ATTENTION

Ensure that no pipes or cables are laid in the wall beneath the mounting location that could be damaged by the

installation.

5Supply line at the heatcon! WG

The electrical installation must be carried out with fixed wiring in accordance with DIN VDE 0100-520.

The supply line must be protected by the emergency heating switch.

6Connection terminals

The sensors, pumps and other components are connected according to the connection diagram in the housing ceiling

of the wall-mounted housing.

The setup wizard of the heatcon! EC preassigns the inputs and outputs. When wiring, pay attention to the desired

functions according to the preassignment of the connection terminals.

DANGER

When wiring, make sure that all live devices are voltage-free.

7Installation (Parameterization) heatcon! EC

The installation of the heatcon! EC is carried out via a menu-driven setup wizard.

7.1 Installation via MMI

After power on, the setup wizard appears in the MMI.

Install the heatcon! EC as described in the short instructions included the device. Detailed installation

instructions for the heatcon! Systems can be found at https://ebv-gmbh.eu/downloads.

7.2 Installation via Computer/Laptop

7.2.1 Preparation

For the installation of the heatcon! EC via PC/laptop it is necessary to make the internal connections LAN and USB

accessible.

Open the wall-mounted housing by loosening the screws and carefully lifting off the cover.

Note

Make sure that the existing cables remain in place. If cables are removed, their functionality will later be impaired or

no longer exist.

Plug in a USB extension cable to the USB port and a patch cable (LAN) to the LAN port of the heatcon! EC and lead the

cables into the area of the accessible terminal strips.

Carefully reinsert the housing cover and tighten the screws.

7.2.2 Installation

Connect the heatcon! EC with the network. Plug the LAN cable into a free port of the Internet router or a switch.

For installation, the USB port of the heatcon! EC is connected to the USB LAN Adapter from the heatapp! installation

kit. The LAN port is connected to the network card of your laptop.

The details of the installation can be found in the heatcon! system installation guide! Detailed

installation instructions for the heatcon! System can be found under https://ebv-gmbh.eu/downloads.

8Finishing

Finally, put on the cover of the wall mounting housing and tighten the screws.

Table des matières

Manuels Système de chauffage populaires d'autres marques

aerauliqa

aerauliqa QR350ABP Manuel utilisateur

WatchGas

WatchGas ATEX BEACON Manuel utilisateur

Viessmann

Viessmann Vitoligno 300-H Mode d'emploi

Lampoassa

Lampoassa 203GT Manuel utilisateur

MSA

MSA SOA-1022 Manuel utilisateur

nilan

nilan Compact P Manuel utilisateur

ITR

ITR OASIS NE-S Manuel utilisateur

Carrier

Carrier 48LJD Dimensions et guide d'installation

aldes

aldes EVEREST XV Manuel utilisateur

Kober

Kober C22SPV23MEF Manuel utilisateur

Oxygen

Oxygen X-Air V400 Manuel utilisateur

Carrier

Carrier FB4CNF Manuel utilisateur

Kroll

Kroll HM200 Manuel

Kroll

Kroll HM200 Manuel

NuAire

NuAire XBOXER XBC Series Manuel utilisateur

Trane

Trane VR104GD-U Series Manuel utilisateur

Vents

Vents VUT V mini Manuel utilisateur

Viessmann

Viessmann Divicon Manuel utilisateur

heatcon! WG Manuel utilisateur

Manuels Système de chauffage populaires d'autres marques