HCT MVP-R Series Manuel utilisateur

MVP-R

www.enovationcontrols.com

MVP-R

Proportional Valve Ramping Controller

User Manual

MVP-R

Revision Record

Rev Description

Date Released

Last Updated by

Rev A Initial Revision 16-Dec-13 WB

Rev B

Upgrade to 32V and IP65 ratings 14-Oct-14 WB

Rev C

Removed 2.5A Option 15-Feb-19 CB

MVP-R

Contents

Revision Record...................................................................................................................................................... 2

HCT Introduction..................................................................................................................................................... 4

Product Use Limitations .......................................................................................................................................... 4

Product Application Guidelines ............................................................................................................................... 5

MVP-R Ramping Controller .................................................................................................................................... 6

Operating Specifications ................................................................................................................................. 6

Physical Description........................................................................................................................................ 7

User Interface ................................................................................................................................................. 7

Configuration................................................................................................................................................... 8

Parameter List............................................................................................................................................... 11

Wiring ............................................................................................................................................................ 13

Order Information .................................................................................................................................................. 13

Application Examples............................................................................................................................................ 14

Single Solenoid Control ................................................................................................................................ 14

MVP-R

HCT Introduction

Welcome to High Country Tek Inc. HCT is North America’s foremost independent designer and producer of

modular, ruggedized digital and analog electronic controllers for the fluid power industry.

From our factory in California, we manufacture ‘specialty’ controllers for specific functions and the user

programmable ‘DVC family’ to enable large area networked system solutions.

The modules are used in mobile, industrial and marine applications. They are also applied successfully in other

industry segments.

HCT products are encapsulated in solid flame resistant material for maximum durability, electrical integrity and

complete environmental security.

HCT is a market leader in many application arenas, including hydraulic generator, e-Fan and hydraulic fan system

controls. These controllers facilitate significant fuel, emission and operational savings.

HCT’s market neutrality offers integration with any hydraulic OEM valves, pumps, sub-systems or systems.

For more information, please visit us at: www.enovationcontrols.com.

Product Use Limitations

HCT products may not be suited for any of the following applications:

•Any product which comes under the Federal Highway Safety Act, namely steering or braking systems for

passenger-carrying vehicles or on-highway trucks.

•Aircraft or space vehicles.

•Ordinance or military equipment.

•Life support equipment.

•Any end product which, when sold, comes under U.S. Nuclear Regulatory Commission rules and regulations.

HCT does not have any performance assurance programs for testing their products for the above applications.

HCT's products are not designed for these applications and HCT does not warrant, recommend, or specifically

approve its products for these applications.

The user shall be solely responsible for any loss or damages occasioned by breach of the provisions of this

paragraph and shall carry product liability and liability insurance to insure against such loss or damages.

MVP-R

Cautions

Changing setup values or operating modes while a machine is running may cause unintended machine movement.

It could lead to possible injury or death. Any moving parts should be disabled prior to changing setup values or

operating modes. In every case, exercise caution and work should be completed only by qualified personnel.

Product Application Guidelines

ALWAYS do the following

•FULLY read this manual and accompanying data sheets BEFORE starting.

•Isolate this unit from all other equipment BEFORE any form of welding.

•Isolate the controller from ANY form of battery charging or battery boosting.

•Be aware of the electrical & mechanical connections, and the expected reactions of the equipment.

•Operate the units within the temperature range.

•Use the correct tools to do the job (i.e. P.C., software) etc.

•Separate High Voltage AC cables from Low Voltage DC signal and supply cables.

•Make sure power supply is CORRECT, ELECTRICALLY CLEAN, STABLE, and rated for the full load.

•Make sure the controller output voltage & current is compatible with the equipment.

•All unused wires / terminals should be terminated safely.

•Ensure ALL connectors have no unintended SHORT or OPEN circuits.

•Ensure ALL connectors are wired correctly, secure, locked in place and fully connected.

•Disconnect or connect wires to or from this unit only when the power supply is disconnected.

•Use adequate screening in areas of intense Radio Frequency fields.

•Ensure ALL work areas are clear of personnel before operating the controller.

•Follow and abide by local and country health & safety standards.

MVP-R

MVP-R Ramping Controller

The MVP-R controller drives proportional solenoid valves with adjustable ramp times.

Once configured, the settings are permanently stored in the controller memory.

MVP-R Features

Easily configured using HCT Graphical User Interface (GUI) or HCT Hand Held Interface (HHI)

LED indication of power, output current and fault status

Permanently sealed, standard DIN 43650 Form A connector body with pre-wired 18AWG PVC cable

Single coil applications, programmable enable input

Output limits are independently adjustable

Adjustable output with short circuit protection

Adjustable ramp up and ramp down times (RP1 has ramp up only)

Operating Specifications

Supply Voltage 9 to 32VDC

Supply Current Valve current + 20mA (Quiescent Max)

Output Current -06A: 600mA MAX -12A: 1.2A MAX -25A: 2.5A MAX

Coil Resistance 2Ω MIN.

Dither Frequency 80, 100, 120, 140, 160, 180, 200, 220, 240, 260, 280, 300.

(Select OFF for 1000Hz)

Ramp Functions -RP1: ramp up only -RP2: ramp up and down

Enable Input Voltage (RP2) 9 to 32VDC

Operating Temperature Range -40º to 85º C (operating); -60º to 90º C (storage)

Enclosure 33% glass reinforced, heat stabilized, black polyamide 66

Dimensions Inch: 2.4 L x 1.2 W x 0.75 H; Mm: 60 L x 30 W x 19 H

NEMA/IP Rating NEMA 4 / IP67

MVP-R

Physical Description

There are two indicator LEDs: STATUS and OUTPUT. The STATUS LED is green when the applied voltage is

within the operating range.

The OUTPUT LED is yellow and the brightness will vary with the output current.

In the case of a fault the STATUS LED will flash red with a flash code. See Fault Status for details.

The MVP communicates with the Graphical User Interface through an infrared interface port to RS232. The infrared

adapter clips onto the MVP-R aligning with the notches in the sides. It must be powered when configuring the

settings.

User Interface

The MVP has a number of internal settings.

Users can open the Graphical User Interface to view, make changes and save the settings in a data file, which can

be uploaded to any MVP controller.

30mm

60mm

19mm

DIN

43650

Form A

MVP-R

The users can use the Hand Held Interface to view and make changes, but can not save the settings in a data file.

The programmer, cable and adapter are self-contained which makes HHI a viable alternative for field work.

Configuration

The GUI has 4 buttons: Lock, Unlock, Up, and Down. There are short-cut keys: ‘/’(lock), ‘*’(unlock), ‘+’(up), and ‘-

‘(down).

The HCT Hand Held Interface has the same 4 buttons and a 2-line LCD display.

Use the up and down arrows to navigate through the parameter list. The display will show the next parameter in the

list when pressed. The parameter name is on the first line and the value is on the second line. The list scrolls,

stepping down from the last parameter to the first and vice-versa.

There are three types of parameters: fixed; monitor; and variable. Fixed parameters show the module’s firmware

version, etc. Monitor parameters display output current and system voltage. Use variable parameters to configure

the controller, such as maximum output current, operating mode, etc. Some parameters combine variable and

monitor in one line. Use it to set a variable according to the current monitor value.

Press the unlock button to enter the edit mode. An asterisk (*) will appear at the beginning of the second line. Use

the up and down buttons to change the value. For parameters containing both variable and monitor, the monitor

data is in square brackets.

Press the lock button to save the parameters and end edit mode.

MVP-R

When the lock button is pressed, the changes take effect immediately. Change values only when the machine is

NOT running.

“Read settings from controller” displays a static table of values from non-volatile memory. The changes made to the

settings by selecting “lock” are not updated in the table unless “read settings from controller” is selected again.

To save the settings into a file for future use, click “read settings from controller” before clicking “save settings to

file”.

MVP-R

When uploading settings from a data file, the static table shows the settings from the data file, but they are not in

the controller yet.

Click “write settings to controller” before clicking “read settings from controller”. After this step, the static table will

display the MVP settings from the data file.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HCT Contrôleurs

HCT

HCT evc Manuel utilisateur

HCT

HCT DRF2 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur