Hawg Wired MPS3004 Manuel utilisateur

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 2 NEWARK, CA

CONGRATULATIONS! YOU’VE JUST PURCHASED WHAT WE CONSIDER TO BE THE FINEST MOTORCYCLE

AUDIO EQUIPMENT AVAILABLE. WE TAKE PRIDE IN THE FACT THAT YOU’VE CHOSEN HAWG WIRED

PRODUCTS, AND WELCOME YOU TO OUR FAMILY OF AUDIOPHILE ENTHUSIASTS. OUR GOAL HERE IS

SIMPLE – TO BRING HIGH PERFORMANCE AUDIO FIDELITY TO YOU, THE RIDER, WITHOUT COMPROMISING

YOUR BIKE’S ELECTRICAL SYSTEM OR STORAGE SPACE. SOME SIDE EFFECTS MAY OCCUR HOWEVER,

INCLUDING BUT NOT LIMITED TO; PUZZLED LOOKS FROM OTHER MOTORISTS, OCCASIONAL SHOUTS

FROM YOUR NEIGHBORS, AND THE ENVY OF YOUR FRIENDS. AFTER YEARS OF DESIGN

AND ENGINEERING, CUSTOM CRAFTSMANSHIP, AND A CRAVE FOR CLEAN, CLEAR,

LOUD MUSIC, WE BELIEVE WE’VE NAILED THIS STUFF DOWN RIGHT.

THANK YOU FOR YOUR SUPPORT

THE HAWG WIRED TEAM

PLEASE RECORD THE MODEL AND SERIAL NUMBER[S] OF YOUR EQUIPMENT IN THE SPACE PROVIDED

BELOW AS YOUR PERMANENT RECORD. THESE NUMBERS CAN BE FOUND ON THE FRONT AND/OR

BOTTOM OF EACH COMPONENT. THIS WILL ASSIST US WITH YOUR FACTORY WARRANTY COVERAGE, AND

MAY BE USEFUL TO YOU IN THE UNFORTUNATE EVENT THAT IT’S STOLEN.

MODEL NUMBER[S]: SERIAL NUMBER[S]:

KIT ITEMS INCLUDED (BY QUANTITY): MPS3002

RS4002

MPS3004

RS4004

MPS3002 / RS4002 2 CHANNEL MAIN AMPLIFIER 1 1

MPS150 / RS200 SATELLITE AMPLIFIER 1

10 AWG POWER / GROUND CABLE 1 1

MAIN I/O HARNESS (FRONT HIGH LEVEL / FRONT SPEAKER OUT / REMOTE) 1 1

REAR SPEAKER OUTPUT CABLE 1

REAR HIGH LEVEL INPUT CABLE 1

LOW LEVEL (RCA TO PHONO) INPUT CABLE 1 2

CONTROL CABLE 1

SATELLITE BRACKET (BATWING USE ONLY) 1

LARGE VELCRO PAD 1 1

SMALL VELCRO PAD 1

30 AMP ATC FUSE 1 1

18 AWG BARREL CRIMP 8

8” BLACK ZIP TIE 6 6

DIELECTRIC GREASE PACKET 1 1

ALCOHOL CLEANING PAD 2 2

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 3 NEWARK, CA

THIS SECTION IS INTENDED TO BRING YOU UP TO SPEED WITH OUR DOCUMENTATION CONVENTIONS.

WE RECOMMEND READING THIS MANUAL THOROUGHLY BEFORE BEGINNING YOUR INSTALLATION TO

ACHIEVE A TROUBLE FREE, LONG LASTING OUTCOME.

TERMINOLOGY USED IN THIS MANUAL:

SOURCE UNIT REFERS TO THE DEVICE THAT SUPPLIES THE AMPLIFIER WITH AUDIO INPUT,

TYPICALLY YOUR RADIO, HEAD UNIT, MEDIA DEVICE, ETC.

MAIN AMPLIFIER MPS3002 OR RS4002, MASTER 2 CHANNELS AMPLIFIERS THAT FUNCTION

STANDALONE. THE BIGGEST BOX IN THE KIT.

SATELLITE AMPLIFIER MPS150 OR RS200, ADD-ON AMPLIFIER THAT CONNECTS TO A MAIN AMPLIFIER.

ONLY USED FOR MORE THAN 2 CHANNELS. THE SMALL BOX IN YOUR KIT.

CONTROL CABLE USED TO CONNECT A SATELLITE AMPLIFIER TO THE MAIN AMPLIFIER FOR SYSTEMS

WITH MORE THAN 2 CHANNELS.

REMOTE TURN-ON WIRE USED TO SWITCH THE AMPLIFIER SYSTEM ON/OFF, USUALLY CONTROLLED BY YOUR

IGNITION SYSTEM (CIGARETTE LIGHTER METHOD), OR BY THE REMOTE LEAD OF AN

AFTERMARKET SOURCE UNIT.

LOW LEVEL INPUT CABLE USED WHEN RCA CONNECTORS ARE THE SOURCE OF INPUT TO THE AMPLIFIER,

TYPICALLY USED WITH AFTERMARKET SOURCE UNITS (PREFERRED METHOD).

HIGH LEVEL INPUT CABLE USED WHEN SPEAKER WIRES ARE THE ONLY SOURCE OF INPUT TO THE AMPLIFIER,

TYPICALLY USED WITH A FACTORY SOURCE UNIT.

BATWING FAIRING HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ELECTRA GLIDE MODELS, FORK

MOUNTED, SINGLE HEADLIGHT STYLE.

SHARKNOSE FAIRING HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ROAD GLIDE MODELS, FRAME

MOUNTED (FIXED), DUAL HEADLIGHT STYLE.

MANUFACTURER INSTRUCTIONS REFERS TO ANY DOCUMENTATION PROVIDED BY A MANUFACTURER OTHER THAN

HAWG WIRED (IE. HARLEY-DAVIDSON®SHOP REPAIR MANUAL, AFTERMARKET

SOURCE UNIT OR SPEAKER MANUAL, ETC.).

QUICK CONNECT SYMBOLS:

KEEP AN EYE OUT FOR THE “QUICK CONNECT” SYMBOLS THROUGHOUT THIS MANUAL; THEY PROVIDE A

VISUAL LINK BETWEEN INSTRUCTIONS, DIAGRAMS, AND THE SYSTEM COMPONENTS.

POWER BATTERY POSITIVE (+12VDC)

GROUND BATTERY NEGATIVE (–), CHASSIS GROUND

REMOTE REMOTE TURN-ON LEAD ACTIVATED BY +12VDC

FUSE ESSENTIAL PROTECTION FROM SHORTS

LINE-IN SOURCE INPUT, LOW LEVEL OR HIGH LEVEL INPUT

CONTROL MAIN AMPLIFIER TO SATELLITE AMPLIFIER CONNECTION

SPEAKER TERMINAL BLOCK CONNECTIONS FOR SPEAKER OUTPUT

CONFIGURE AMPLIFIER CONFIGURATION FEATURES (GAIN, CROSSOVERS, ETC.)

NOTE: IF ANYTHING ABOUT THE INSTRUCTION OR INFORMATION PROVIDED IN THIS MANUAL IS UNCLEAR, QUESTIONABLE,

OR YOU THINK WE’RE DEAD WRONG ABOUT SOMETHING, PLEASE CONTACT US.

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 4 NEWARK, CA

INITIAL TEAR-DOWN

IF YOU HAVEN’T ALREADY, GET FAMILIAR WITH YOUR NEW SYSTEM BY BROWSING THE “USER GUIDE” SECTION OF THIS

MANUAL. UNDERSTANDING YOUR EQUIPMENT FIRST CAN MAKE THE INSTALLATION INSTRUCTIONS EASIER TO FOLLOW.

1. WITH THE IGNITION SWITCH OFF, REMOVE THE SEAT.

WARNING: KEEP THE IGNITION SWITCH OFF THROUGHOUT THE ENTIRE INSTALLATION PROCESS.

TIP: REFER TO MANUFACTURER INSTRUCTIONS IF NECESSARY.

2. DISCONNECT THE NEGATIVE (–) SIDE OF THE BATTERY, FOLLOWED BY THE POSITIVE (+) SIDE.

WARNING: BE SURE TO PREVENT THE LOOSE BATTERY CABLES FROM CONTACTING THE EXPOSED BATTERY

TERMINALS ACCIDENTALLY DURING THE INSTALLATION PROCESS.

3. CAREFULLY REMOVE THE FRONT FAIRING COVER, NOTING WHICH HOLE EACH SCREW COMES

FROM, AS LENGTHS AND SIZES MAY DIFFER.

TIP: REFER TO MANUFACTURER INSTRUCTIONS IF NECESSARY, AND DON’T FORGET TO COVER YOUR FENDER.

WHILE YOU HAVE THIS THING APART, TAKE A MINUTE TO CHECK A FEW THINGS AT THE SAME TIME. BURNT OUT GAUGE

BULBS, LOOSE HARNESS CONNECTORS CAUSING RATTLES, THAT SEAL THAT NEVER FAILS TO FALL OFF THE EDGE OF

THE INNER FAIRING WITHOUT SOME TRIM ADHESIVE, INSTALLING THOSE NEW GAUGES YOU’VE BEEN WANTING TO GET…

4. DISCONNECT THE SPEAKER WIRING FROM THE FACTORY SPEAKERS (IF APPLICABLE).

4.1. FACTORY SOURCE UNIT

2 AND 4 CHANNEL SOURCE,

DISCONNECT THE FRONT

SPEAKER WIRES FROM THE

FACTORY SPEAKERS IN THE

FAIRING AND PUT ASIDE FOR

HIGH-LEVEL INPUT USE LATER.

4 CHANNEL SOURCE, IF RETAINING YOUR FRONT/REAR

FADER IS REQUIRED, GAIN ACCESS TO THE AUXILIARY

HARNESS AND CUT THE 4 WIRES IN A PLACE WHERE YOU

CAN EASILY BARREL CRIMP NEW WIRES TO ALL 8 WIRE

ENDS. PUT ASIDE FOR REAR HIGH-LEVEL INPUT AND NEW

SPEAKER WIRE USE LATER.

4.2. AFTERMARKET SOURCE UNIT

2 AND 4 CHANNEL SOURCE, DISCONNECT ANY FACTORY SPEAKER WIRES FROM THE BACK

OF SPEAKERS AND SECURE THEM OUT OF THE WAY.

4 CHANNEL

SOURCE WIRES

H-D® SOURCE UNIT MODELS

1998-2005

8 OHM

1998-20XX

CVO

2006-20XX

2 OHM

REAR LEFT +

BRN

(PIN 10)

BRN

(PIN 10)

BRN3

(PIN 2)

REAR LEFT –

WHT/BRN

(PIN 3)

WHT/BRN

(PIN 3)

WHT/BRN3

(PIN 25)

REAR RIGHT +

GRN

(PIN 11)

GRN

(PIN 11)

GRN3

(PIN 1)

REAR RIGHT –

L.GRN/BRN

(PIN 4)

L.GRN/BRN

(PIN 4)

L.GRN/BRN3

(PIN 24)

PIN NUMBERS APPLY TO OVERLAY HARNESS CONNECTOR

TIP: CUTTING A FEW WIRE TIES AND PULLING BACK LOOM WILL MAKE YOUR HARNESS MUCH EASIER TO WORK WITH.

CHECK AND RE-CHECK AGAIN BEFORE CUTTING ANY FACTORY WIRES.

AT THIS POINT, TAKE A VISUAL INVENTORY OF YOUR INNER FAIRING. SECURE ANY LOOSE WIRES OR LOOMS AWAY FROM

MOUNTING LOCATIONS WITH ZIP TIES. WITH THE MAIN AMPLIFIER TEMPORARILY IN PLACE, PERFORM A TEST FIT OF THE

FRONT FAIRING COVER TO ENSURE THAT NO CONTACT OCCURS BEFORE PROCEEDING.

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 5 NEWARK, CA

[

]

COMPONENT MOUNTING

USING VELCRO®AS A MOUNTING METHOD HAS THE FOLLOWING ADVANTAGES; IT HOLDS WELL UNDER EXTREME

VIBRATION CONDITIONS, PROVIDES SOME MEASURE OF SHOCK ABSORPTION, AND ALLOWS FOR SIMPLE INSTALLATION,

REMOVAL, AND ADJUSTMENT. HOWEVER, ONCE YOU STICK THOSE TWO SIDES TOGETHER WITH SOME PRESSURE, YOU’D

DO WELL TO USE A PUTTY KNIFE SEPARATING THE TWO AGAIN. USING A PIECE OF PAPER OR THIN CARDBOARD BETWEEN

THE 2 PIECES OF VELCRO WHEN TEST FITTING CAN MAKE THINGS A LOT EASIER.

NOTE: BE SURE TO CLEAN ALL ADHESIVE MATING SURFACES WITH THE INCLUDED ALCOHOL PADS BEFORE ATTACHING

THE ADHESIVE VELCRO®PATCHES. ONCE THE ADHESIVE SIDE IS APPLIED TO A CLEAN SURFACE, WORK OUT THE AIR

POCKETS WITH YOUR FINGER TIPS FOR MAXIMUM HOLDING STRENGTH AND LONGEVITY.

5. DETERMINE THE MOUNTING LOCATION FOR THE AMPLIFIER BASED ON YOUR FAIRING:

5.1. BATWING FAIRINGS

MOUNT THE MAIN AMPLIFIER (A) ON TOP OF THE

SOURCE UNIT USING ONE OF THESE METHODS:

2005 AND OLDER - USE THE LARGE VELCRO® PATCH

PROVIDED.

2006 AND NEWER - CUT THE LARGE VELCRO® PATCH IN

HALF AND CHOOSE THE APPROPRIATE METHOD BELOW:

WITH BOTH FACTORY XM AND CB MODULES INSTALLED ABOVE THE SOURCE UNIT, USE THE TWO PATCH

HALVES, ONE ON EACH MODULE.

WITH NO FACTORY MODULES INSTALLED ABOVE THE SOURCE UNIT, USE THE TWO PATCH HALVES, ONE ON

EACH SIDE OF THE RIB RUNNING DOWN THE MIDDLE OF THE SOURCE UNIT.

WITH ONLY ONE FACTORY MODULE INSTALLED ABOVE THE SOURCE UNIT, INSTALL THE HKA150 ADAPTER

BRACKET (SOLD SEPARATELY) IN THE BLANK MODULE SLOT, AND THEN USE THE TWO PATCH HALVES, ONE

ON EACH MODULE.

REMOVE BOTH LEFT AND RIGHT FACTORY SPEAKER BRACES AND INSTALL THE SATELLITE

BRACKET TO THE INNER FAIRING BRACE ON EITHER

SIDE REUSING THE FACTORY HARDWARE. MOUNT THE

SATELLITE AMPLIFIER (B) TO THE BRACKET USING THE

SMALL VELCRO®PATCH PROVIDED.

5.2. SHARKNOSE FAIRINGS

MOUNT THE MAIN AMPLIFIER (A) ON THE FLAT SPACE

BENEATH THE GLOVE BOX USING THE LARGE VELCRO®

PATCH PROVIDED. MOUNT THE SATELLITE AMPLIFIER

(B); IN FRONT OF MAIN AMPLIFIER USING THE SMALL

VELCRO®PATCH PROVIDED.

5.3. CUSTOM INSTALLS – MOUNTING LOCATIONS CAN VARY, AND MUST BE TEST FIT ON A ONE-

BY-ONE BASIS. CHECK FOR PROPER CLEARANCES BEFORE CONTINUING WITH THE

INSTALLATION. THE WIRING KIT MAY NOT INCLUDE LONG ENOUGH WIRING NEEDED TO

COMPLETE SOME CUSTOM INSTALLATIONS.

FOR ALL “TOP OF THE SOURCE UNIT” INSTALLATIONS, ENSURE THAT THE MAIN AMPLIFIER IS POSITIONED AS FAR BACK

TOWARDS THE INNER FAIRING AS POSSIBLE.

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 6 NEWARK, CA

[

]

WIRING THE MAIN AMPLIFIER

SOME BIKES MAY REQUIRE THAT THE GAS TANK BE LOOSENED OR REMOVED TO PROPERLY ROUTE THE POWER WIRE.

PLEASE TAKE EVERY POSSIBLE PRECAUTION NECESSARY WHEN DEALING WITH YOUR GAS TANK! DEFINITELY REFER TO

MANUFACTURER INSTRUCTIONS IF NECESSARY.

6. ROUTE AND CONNECT THE POWER WIRE (WITHOUT THE IN-LINE FUSE INSTALLED) FROM THE

POSITIVE (+) BATTERY TERMINAL (FIG. 6.A), UNDER THE RIGHT SIDE (PASSENGER, STARBOARD,

ETC.) OF THE GAS TANK, THROUGH THE FAIRING, AND TO THE MAIN AMPLIFIER. THE BLACK

SLEEVE SHOULD END UP COVERING THE EXPOSED POWER WIRE BETWEEN THE GAS TANK AND

THE FAIRING.

WARNING: DO NOT INSTALL THE IN-LINE FUSE UNTIL INSTRUCTED TO DO SO.

NOTE: ON 2006 AND NEWER, WE RECOMMEND UTILIZING THE FACTORY WIRING HARNESS CHANNEL UNDER THE

TANK WITH A SUITABLE WIRE FEEDING TOOL OR DEVICE. USE OF A COAT HANGER IS AT YOUR OWN RISK.

FIGURE 6 – POWER AND GROUND ROUTING AND CONNECTIONS

7. CONNECT THE GROUND WIRE TO CHASSIS GROUND (FIG. 8.B). TYPICALLY AN EXISTING SCREW

OR NUT ON THE BIKE FRAME SHOULD BE USED, PREFERABLY WHERE A FACTORY GROUND

STRAP ALREADY EXISTS.

TIP: THE MAJORITY OF PROBLEM INSTALLS ARE THE RESULT OF A POOR GROUND. REFER TO “BE WELL

GROUNDED” IN THE INSTALLATION CONSIDERATIONS SECTION FOR MORE INFORMATION.

8. CONNECT THE MAIN I/O HARNESS. ROUTE AND CONNECT THE REMOTE TURN-ON WIRE FROM THE

AMPLIFIER LABELED REM TO ONE OF THE

FOLLOWING LOCATIONS:

8.1. FACTORY SOURCE UNITS – TO UTILIZE THE

CIGARETTE LIGHTER METHOD, DISCONNECT

THE POWER TERMINAL FROM THE BACK OF

THE LIGHTER (FIG. 8.A) AND CONNECT IT TO

THE MALE TERMINAL OF THE REMOTE TURN-

ON WIRE (FIG. 8.B). THEN CONNECT THE

FEMALE TERMINAL TO THE LIGHTER

TERMINAL (FIG. 8.C). THIS WILL TURN THE

AMPLIFIER ON/OFF WITH THE IGNITION

SWITCH.

8.2. AFTERMARKET SOURCE UNITS - REFER TO YOUR SOURCE UNIT INSTRUCTIONS TO

DETERMINE IT’S REMOTE TURN-ON LEAD. THIS WILL TURN THE AMPLIFIER ON/OFF WITH

THE SOURCE UNIT POWER SWITCH.

FIGURE 8 – CIGARETTE LIGHTER METHOD

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 7 NEWARK, CA

[

]

WIRING THE MAIN AMPLIFIER (CONTINUED)

9. DETERMINE AND CONNECT YOUR SOURCE UNIT OUTPUT TO THE AMPLIFIER INPUT CABLE(S)

USING ONE OF THE FOLLOWING HIGH OR LOW LEVEL INPUT METHODS:

9.1. FACTORY SOURCE UNITS - HIGH LEVEL INPUT (NO RCA CONNECTORS AVAILABLE)

2 CHANNEL SOURCE, CONNECT THE FRONT SPEAKER OUTPUT WIRES FROM THE SOURCE

UNIT TO THE HIGH LEVEL INPUT CABLE (USE ATTACHED TERMINALS TO CONNECT INPUT

WIRES TO THE SPEAKER WIRE TERMINALS IF POSSIBLE).

4 CHANNEL SOURCE, CONNECT THE FRONT AND REAR SPEAKER WIRES FROM THE SOURCE

UNIT TO THE HIGH LEVEL INPUT CABLES RESPECTIVELY.

NOTE: FOR CUSTOM WIRING CONNECTIONS, WE RECOMMEND CRIMP, SOLDER, AND HEAT SHRINK.

HIGH LEVEL INPUT CABLE(S)

CONNECT

TOGETHER

H-D® SOURCE UNIT MODELS

2 CHANNEL – USE FRONT ONLY

4 CHANNEL – USE BOTH

1998-2005

8 OHM

1998-20XX

CVO1

2006-20XX

2 OHM

FRONT LEFT + WHT 



f

f

e

e



WHT/ORG

(PIN 16)

WHT/ORG

(PIN 16)

WHT/ORG

(PIN 16)

FRONT LEFT – BLK (WHT TWIST) 



f

f

e

e





L.GRN/WHT

(PIN 17)

L.GRN/WHT

(PIN 17)

L.GRN/WHT

(PIN 17)

FRONT RIGHT + RED 



f

f

e

e





GRY/RED

(PIN 18)

GRY/RED

(PIN 18)

GRY/RED

(PIN 18)

FRONT RIGHT – BLK (RED TWIST) 



f

f

e

e





L.GRN/BLK

(PIN 1)

L.GRN/BLK

(PIN 1)

L.GRN/BLK

(PIN 1)

REAR LEFT + WHT 



f

f

e

e





BRN

(PIN 10)

BRN

(PIN 10)

BRN

(PIN 2)

REAR LEFT – BLK (WHT TWIST) 



f

f

e

e





WHT/BRN

(PIN 3)

WHT/BRN

(PIN 3)

WHT/BRN

(PIN 25)

REAR RIGHT + RED 



f

f

e

e





GRN

(PIN 11)

GRN

(PIN 11)

GRN

(PIN 1)

REAR RIGHT – BLK (RED TWIST) 



f

f

e

e





L.GRN/BRN

(PIN 4)

L.GRN/BRN

(PIN 4)

L.GRN/BRN

(PIN 24)

PIN NUMBERS APPLY TO H-D MAIN AND OVERLAY HARNESS CONNECTORS

NOTE1: CVO BIKES MAY BE EQUIPPED WITH A HIGH-OUTPUT SOURCE UNIT; DO NOT USE THE FOLLOWING WIRE

COLORS: WHT/PNK, PNK, WHT/GRY, GRY. THESE OUTPUTS CAN DAMAGE THE AMPLIFIER INPUTS.

9.2. AFTERMARKET SOURCE UNITS - LOW LEVEL INPUT (RCA OUTPUT CONNECTORS AVAILABLE)

2 CHANNEL SOURCE, CONNECT THE FRONT RCA OUTPUT CONNECTORS FROM THE SOURCE

UNIT TO THE LOW LEVEL INPUT CABLE.

4 CHANNEL SOURCE, CONNECT THE FRONT AND REAR RCA OUTPUT CONNECTORS FROM

THE SOURCE UNIT TO THE LOW LEVEL INPUT CABLES RESPECTIVELY.

NOTE: VERY LITTLE DIELECTRIC GREASE IS NEEDED TO KEEP YOUR CONNECTIONS CORROSION FREE. VERY LITTLE

MOISTURE IS NEEDED TO CORRODE CONTACTS NOT COVERED WITH DIELECTRIC GREASE.

10. PLUG THE CHOSEN INPUT CABLE(S) INTO THE CORRESPONDING CONNECTOR(S) OF THE MAIN

AMPLIFIER LABELED HIGH OR LOW,FRONT AND/OR REAR ACCORDINGLY.

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 8 NEWARK, CA

[

]

WIRING THE SATELLITE AMPLIFIER(S) (4 CHANNEL OPTIONS ONLY)

INSTRUCTIONS 11 – 14 REFER TO 4 CHANNEL SPECIFIC OPTIONS. IF YOU ARE INSTALLING THE MPS3002 OR RS4002 2

CHANNEL SYSTEMS, PLEASE SKIP AHEAD TO INSTRUCTION 15.

11. CHANNEL INPUT MODE SWITCH:

SET THIS SWITCH TO 2CH - 2 CHANNEL MODE OR 4CH – 4 CHANNEL MODE TO MATCH THE INPUT

METHOD YOU’RE NOW WIRED FOR IN STEPS 11 – 13:

11.1. 2CH - 2 CHANNEL MODE, USED FOR 2 CHANNEL SOURCE INPUT CONFIGURATIONS.

11.2. 4CH - 4 CHANNEL MODE, USED FOR 4 CHANNEL SOURCE INPUT CONFIGURATIONS.

NOTE: THIS SWITCH IS EXPLAINED IN DETAIL LATER IN THE “USER GUIDE” SECTION.

12. APPLY A SMALL AMOUNT OF DIELECTRIC GREASE (INCLUDED IN THE KIT) TO EACH CONTROL

CABLE CONNECTOR OF YOUR SYSTEM; CONTROL CABLE (BOTH ENDS), MAIN AMPLIFIER

CONNECTOR, AND THE SATELLITE AMPLIFIER CONNECTOR, FOCUSING ON THE ELECTRICAL

CONTACTS INSIDE THE PLASTIC CONNECTOR HOUSINGS.

NOTE: VERY LITTLE DIELECTRIC GREASE IS NEEDED TO KEEP YOUR CONNECTIONS CORROSION FREE. VERY

LITTLE MOISTURE IS NEEDED TO CORRODE CONTACTS NOT COVERED WITH DIELECTRIC GREASE.

13. WITH THE AMPLIFIER OFF, ROUTE AND CONNECT THE CONTROL CABLE FROM THE APPROPRIATE

CONNECTOR ON THE MAIN AMPLIFIER TO THE SATELLITE AMPLIFIER INSTALLED.

WARNING: NEVER CONNECT OR DISCONNECT THE CONTROL CABLES WHILE THE MAIN AMPLIFIER IS POWERED ON. THIS

CAN DAMAGE THE MAIN AND/OR SATELLITE AMPLIFIER(S), AND WILL VOID YOUR WARRANTY AS WELL!

KEEP IN MIND THAT IF YOU PURCHASED THE MPS3002 OR RS4002 AMPLIFIER AS A 2 CHANNEL UPGRADEABLE SYSTEM,

YOU CAN UPGRADE TO A 4 CHANNEL SYSTEM AT ANY TIME BY PURCHASING OUR SATELLITE AMPLIFIER.

WIRING THE SPEAKERS

14. REPLACE THE FACTORY SPEAKERS WITH 4 OHM AFTERMARKET SPEAKERS (IF APPLICABLE).

NOTE: IF YOU ARE INSTALLING HAWG WIRED SPEAKERS, REFER TO THE INSTALLATION INSTRUCTIONS THAT

CAME WITH THEM. IF INSTALLING ANOTHER BRAND OF SPEAKERS, REFER TO THOSE SPECIFIC MANUFACTURER

INSTRUCTIONS IF NECESSARY.

15. ROUTE AND CONNECT THE SPEAKER WIRES FROM THE MAIN AMPLIFIER I/O HARNESS AND REAR

SPEAKER OUTPUT CABLE TO EACH SPEAKER OF YOUR SYSTEM.

NOTE: KEEP THE POLARITIES (+/–) OF EACH WIRE PAIR CORRECT BETWEEN THE AMPLIFIER(S) AND SPEAKERS.

IF YOU ARE INSTALLING HAWG WIRED SPEAKERS, REFER TO THE INSTALLATION INSTRUCTIONS THAT CAME

WITH THEM. IF INSTALLING ANOTHER BRAND OF SPEAKERS, REFER TO THOSE SPECIFIC MANUFACTURER

INSTRUCTIONS IF NECESSARY.

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 9 NEWARK, CA

[

]

TESTING AND TUNING THE SYSTEM

16. RE-CONNECT THE POSITIVE (+) SIDE OF THE BATTERY, FOLLOWED BY THE NEGATIVE (-) SIDE.

WARNING: DO NOT INSTALL THE IN-LINE FUSE UNTIL AFTER THIS STEP.

THIS IS A GOOD TIME TO RE-CHECK YOUR CONNECTIONS BEFORE INSTALLING THE FUSE. MAKE SURE THAT THE

CONTROL CABLE IS COMPLETELY SEATED AND LATCHED IN THEIR RESPECTIVE CONNECTOR, AND THAT POWER AND

GROUND ARE PROPERLY CONNECTED TO THE MAIN AMPLIFIER.

17. INSTALL THE 30 AMP ATC FUSE INTO THE IN-LINE FUSE HOLDER ON THE POWER WIRE.

NOTE: IF THE FUSE DOESN’T BLOW WHEN YOU PLUG IT IN, YOU’VE PASSED THE INITIAL SMOKE TEST.

18. PERFORM A BASIC SYSTEM TEST. TURN THE KEY TO THE ACCESSORY POSITION AND VERIFY

THAT THE AMPLIFIER(S) POWER UP (LED ON EACH COMPONENT SHOULD LIGHT) AND THAT THE

SPEAKERS FUNCTION PROPERLY. IF NOT, PROCEED DIRECTLY TO “TROUBLESHOOTING” IN THE

USER GUIDE SECTION.

19. CONFIGURE, TEST, AND TUNE YOUR SYSTEM BY FOLLOWING THE “TEST AND TUNE”

INSTRUCTIONS GIVEN IN THE “USER GUIDE” SECTION OF THIS MANUAL. WHEN YOU’VE

COMPLETED THESES INSTRUCTIONS AND ARE READY TO ROCK AND ROLL, RETURN HERE TO

COMPLETE THE INSTALLATION.

NOW IT’S TIME TO START ROTATING KNOBS AND FLIPPING SWITCHES TO GET THE MOST OUT OF YOUR NEW SYSTEM. IF

YOU RUN INTO ANY SNAGS ALONG THE WAY, LET US KNOW SO WE CAN HELP GET YOU UP AND RUNNING.

WRAPPING IT UP

20. WITH THE IGNITION OFF, CAREFULLY INSTALL THE FAIRING COVER, ENSURING THAT EACH

ATTACHING SCREW GOES BACK INTO THE HOLE IT CAME OUT OF. ONCE YOU HAVE EVERYTHING

LINED UP AND ALL SCREWS LOOSELY INSTALLED, TIGHTEN EACH SCREW IN AN EVEN PATTERN

TO AVOID BINDING.

WARNING: AVOID OVER-TIGHTENING; PLASTIC THREADS HAVE A TENDENCY TO PULL OUT EASILY. REFER TO

MANUFACTURER INSTRUCTIONS IF NECESSARY.

21. INSTALL THE SEAT, TAKING CARE NOT TO DAMAGE OR PINCH YOUR FACTORY WIRING HARNESS

OR NEW AMPLIFIER POWER WIRE.

TIP: BE SURE THAT BOTH BATTERY TERMINALS ARE CONNECTED AND TIGHT, AND THAT ANY GAS TANK BOLTS

LOOSENED EARLIER ARE NOW TIGHT. REFER TO MANUFACTURER INSTRUCTIONS IF NECESSARY.

76 22. PERFORM A FINAL SYSTEM TEST. TURN THE KEY TO THE ACCESSORY POSITION AND VERIFY

THAT ALL COMPONENTS STILL FUNCTION PROPERLY.

23. PERFORM A TEST RIDE AND AGAIN VERIFY THAT THE SYSTEM IS OK, AND THAT YOUR FRIENDS

ARE SUFFICIENTLY JEALOUS.

TIP: JUSTIN WOULD LIKE TO REMIND YOU TO CHECK YOUR TIRE PRESSURE, AND FROM THE ENTIRE HAWG

WIRED TEAM, THANKS FOR MAKING THIS POSSIBLE, KEEP THE RUBBER SIDE DOWN, AND CRANK IT!

MPS3004 / RS4004 AUDIO SYSTEMS INSTALLATION GUIDE

HAWG WIRED PAGE 10 NEWARK, CA

CONNECTORS AND CONTROLS

PLANNING YOUR SYSTEM CONFIGURATION IS THE FIRST STEP TOWARDS HI-FI HAPPINESS, AND IT’S

TIME YOU GET FAMILIAR WITH ALL THE BELLS AND WHISTLES ON YOUR NEW AMPLIFIER. THE TABLE

BELOW LISTS THE CONTROLS AND CONNECTORS OF THE MPS3002 / RS4002 AND MPS150 / RS200

AMPLIFIERS.

A INPUT GAIN ADJUST J CHANNEL MODE SWITCH S REMOTE CONTROL

B INPUT MODE SWITCH L LOW LEVEL INPUT T LOW LEVEL INPUT (REAR)

C CROSSOVER MODE SWITCH M STATUS INDICATOR U CONTROL IN

D CROSSOVER FILTER ADJUST N MAIN I/O CONNECTOR V SPEAKER OUT (REAR)

E INPUT GAIN ADJUST (REAR) O MAIN POWER CONNECTOR Y MONO / STEREO SWITCH

F INPUT MODE SWITCH (REAR) P AMPLIFIER PROTECTION FUSE Z STATUS INDICATOR

G CROSSOVER MODE SWITCH (REAR) Q HIGH LEVEL INPUT (REAR)

H CROSSOVER FILTER ADJUST (REAR) R CONTROL OUT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hawg Wired Amplificateur

Hawg Wired

Hawg Wired PSC3004 Manuel utilisateur

Hawg Wired

Hawg Wired DCS120 Manuel utilisateur

Hawg Wired

Hawg Wired PSC1502 Manuel utilisateur

Hawg Wired

Hawg Wired CS300 Manuel utilisateur

Hawg Wired

Hawg Wired DCS1202 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur