Hathaway NG2015 Manuel utilisateur

8' HOT SHOT SKEEBALL TABLE

ASSEMBLY INSTRUCTIONS

NG2015

THANK YOU!

Thank you for purchasing this product.

We work around the clock and around the globe to ensure that our products

maintain the highest possible quality. However, in the rare instance that your

product is defective or missing parts, contact your retailer, or call 800-759-0977,

to submit parts requests or warranty claims. Please read the warranty

information at the back of these assembly instructions for further details.

IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS IN

ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.

PARTS IDENTIFIER (NOT TO SCALE)

H1 - 1-1/4” Screw (36) H2 - 5/16” x 1-1/8”

Bolt (12)

H3 - 5/16” Washer (12) H4 - 1/4” x 1-1/4”

Bolt (4)

H5 - 1/4” x 1” Bolt (4) H6 - 1/4” Washer (4) H7 - 1/4” Washer (8) H8 - 3/4” Screw (3)

H9 - 3/8” Screw (4) H10 - 1-1/4” Flat Screw (6) H11 - 1-1/2” Screw (3) H12 - 3/4” Flat Screw (4)

T1 - Allen Wrench (1)

P1L - Left Front Leg (1) P1R - Right Front Leg (1) P2L - Left Middle Leg (1) P2R - Right Middle Leg (1)

P3R - Right Back Leg (1)P3L - Left Back Leg (1)

P6L - Left Front

Side Apron (1)

P6R - Right Front

Side Apron (1)

P7L - Left Back

Side Apron (1)

P7R - Right Back

Side Apron (1)

P4 - Spreader (3) P5 - Front End Apron (1)

PARTS IDENTIFIER (NOT TO SCALE)

P13 - Back

Board (1)

P14 - Electronic

Scorer (1)

P15 - Target

Board (1) P16 - Connect Hinge Set (2) P17 - Net (1)

P12 - Back Bottom

Panel (1)

P11 - Back Upper

Panel (1)

P9 - Front

Top Panel (1)

P10 - Front

Bottom Panel (1)

A1 - Ball (6)

P21A - Support

Panel (1)

P18 - Net Frame Front (1)

P19 - Net Frame Back (1)

Larger

Smaller

(Attaches to Side Apron)

P20 - Net Spacer Bar (2)

P8A - Crossbeam (1) P8B - Crossbeam (2)

P21B - Support

Panel (1)

P22 - “L”Support Panel (1) P23 - Cover Panel (1)

Please see Parts List at end of manual for part number when ordering parts.

For replacement parts please call 800-759-0977.

(Attaches to Side Apron)

ASSEMBLY TIPS

1. Find a clean, level surface to begin the assembly of your game table. The table will be

partially assembled upside down and then turned over onto its legs. This is a heavy game

and turning it over will require at least two strong adults.

2. Remove all of the contents from box and verify that you have all of the parts shown on

Note: Some parts may be pre-installed

or pre-assembled.

understand the text before beginning each assembly step.

4. When installing parts that have more than one screw or bolt, hand tighten all

5. Electric screwdrivers may be helpful during assembly; however, please set a low torque

and use extreme caution because screws may be stripped or overtightened, resulting in

damaged parts, if the electric screwdriver’s torque is set too high.

WARNINGS!

READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETYINSTRUCTIONS CAREFULLY.

CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS

NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.

ASSEMBLY INSTRUCTIONS

Unfinished Side Up

Black Side Down

P10

P21B

Figure 1

1. Find a clean, level place to begin the assembly of your game. We recommend building the unit on the shipping carton to

protect the parts during assembly. Note: The two main units are assembled upside down then turned over for final assembly.

2. Attach the SUPPORT PANEL, P21B, to the FRONT BOTTOM PANEL, P10, using (2) SCREWS, H8, through the two

outer holes as shown in Figure 1. The middle hole will be used in a later step. Note: The P10 panel and P21B support

panel both have pre-drilled holes for screws.

3. Place the LEFT FRONT SIDE APRON, P6L, and RIGHT FRONT SIDE APRON, P6R, upside down and approx. 2 feet

apart, as shown in Figure 2.

4. Insert FRONT TOP PANEL, P9, with finished white side down, into lower grooves of SIDE APRONS, P6L and P6R.

Make sure the end of P9 with the cutouts is on the same end as gear hinge as shown in Figure 2. Slide P9 forward until

the end with cutouts is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly

firmly and attach pieces together using (2) SCREWS, H1, and pre-drilled holes on each side.

5. Attach FRONT END APRON, P5, with groove facing in, using (2) SCREWS, H1, and pre-drilled holes on each side.

Note: Don’t tighten screws all the way until you complete Step 6. This will make it easier to get P10 into P5 groove.

6. Insert FRONT BOTTOM PANEL, P10, with unfinished side up, into upper grooves of SIDE APRONS, P6L and P6R.

Slide P10 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P9. Tighten P5 Screws.

Note: This unit is assembled

upside down.

P6L

Note: Location

of gear hinge

P6R

Note: Location

of gear hinge

Note: Location

of these cutouts

P10

Unfinished

Side Up Slide both

panels in grooves

White

Side Down

Figure 2

7. Attach CROSSBEAM, P8B, with cutout opening facing down and to the left, using (2) SCREWS, H1, and pre-drilled

holes on each side. Use (1) SCREW, H11, to attach center of crossbeam through P10 and into P21B, as shown in Figure 3.

8. Attach LEFT and RIGHT FRONT LEGS, P1L and P1R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as

shown in Figure 3. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader

is attached in next step.

9. Attach SPREADER, P4, using (4) SCREWS, H1, as shown in figure 3. Note: Hand place screws in all four pre-drilled

holes to align panel before tightening.

CAUTION:

P4 SPREADER MUST BE CENTERED

CORRECTLY ONTO PRE-DRILLED HOLES

IN LEGS BEFORE ATTACHING WITH H1

SCREWS.

Figure 3

NOTE: Location

of gear hinge

H11

P8B

P1L

P1R

ASSEMBLY INSTRUCTIONS (CONT.)

10. Attach the SUPPORT PANEL, P21A, to the FRONT BOTTOM PANEL, P10, using (1) SCREW, H8, through the

center hole as shown in Figure 4. The outer two holes will be used in a later step. Note: The P12 panel and P21A support

panel both have pre-drilled holes for screws.

Unfinished Side Up

Black Side Down

P12

P21A

Figure 4

11. Place the LEFT BACK SIDE APRON, P7L, and RIGHT BACK SIDE APRON, P7R, upside down and approx. 2 feet

apart, as shown in Figure 5.

12. Insert BACK TOP PANEL, P11, with finished white side down, into lower grooves of SIDE APRONS, P7L and P7R.

Make sure the end of P11 with the cutouts is on the same end as gear hinge as shown in Figure 5. Slide P11 forward until

the end with cutout is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly

firmly and attach pieces together using (3) SCREWS, H1, and pre-drilled holes on each side.

13. Insert BACK BOTTOM PANEL, P12, with unfinished side up, into upper grooves of SIDE APRONS, P7L and P7R.

Slide P12 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P11.

Note: This unit is assembled

upside down.

P12

P7L

Note: Location

of gear hinge

P7R

Note: Location

of these cutouts

P11

Unfinished

Side Up

Slide both

panels in grooves

White

Side Down

Figure 5

THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)

Figure 6

P2L

P2R

Note: Correct location

of Support Panel to Legs

14. Attach CROSSBEAMS, P8A and P8B, with cutout openings facing down and to the right, using (2) SCREWS, H1, and

pre-drilled holes on each side. Use (1) SCREW, H11, to attach center of CROSSBEAM, P8B, through P12 and into P21A,

assembled in Step 10. Note: Cutouts used as wiring guides in future step. See Figure 6 for correct locations of P8A and P8B.

15. Assemble LEFT and RIGHT MIDDLE LEGS, P2L and P2R, together with SPREADER, P4, using (4) SCREWS, H1,

as shown in Figure 6. Note: Hand place screws in all four pre-drilled holes to align panel before tightening. Attach “L”

SUPPORT PANEL, P22, in same manner using (6) SCREWS, H10, as shown.

16. Attach Middle Leg Assembly between assembled sides, P7L and P7R, using (2) BOLTS, H2, and (2) WASHERS, H3,

on each leg, as shown in Figure 6. Attach “L” SUPPORT PANEL, P22, to table using SCREW, H11, in middle pre-drilled

hole. Note: Velcro will be used as wire harness in future step.

17. Attach LEFT and RIGHT BACK LEGS, P3L and P3R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as

shown in Figure 4. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader

is attached in next step.

18. Attach SPREADER, P4, between Legs using (4) SCREWS, H1, as shown in figure 6.

Note: Hand place screws in all four pre-drilled holes to align panel before tightening.

Velcro

ASSEMBLY INSTRUCTIONS (CONT.)

CAUTION:

P4 SPREADER MUST BE CENTERED

CORRECTLY ONTO PRE-DRILLED HOLES

IN LEGS BEFORE ATTACHING WITH H1

SCREWS.

H10

H11

P22

P4 P3L

P8A

H2 H3

P3R

P8B

P22

ASSEMBLY INSTRUCTIONS (CONT.)

Figure 7

H5 Bolt

Washer

P15

Note: Hinge Gear Assemblies Must Mesh

Note: This Hinge is Threaded and Must Be on Inside

CAUTION:

Pinch Point

CAUTION:

Pinch Point

Reset Button

Reset

Button

No Gap

Ligature

Bundle of

White Wire

P16

Hinge Set

P16

Hinge Set

P7R

Back Side

Apron

P6R

Front Side

Apron

Note: This Hinge is NOT Threaded

and Must Be on Outside

Washer

19. With the help of another adult, set both completed assemblies upright and position so gears face each other as shown

in Figure 7. Using (2) HINGE SETS, P16, connect assemblies using BOLT, H5, and Washer, H7, as shown in Figure 7.

The bolts should be snug, but NOT over tightened as this is a pivot area. Note: Hinge gear assemblies must mesh together,

per diagram, and there should be no gap between playfields. Also, only one hinge plate per set is threaded and must be

installed on the inside of each playfield side.

20. Place TARGET BOARD, P15, with red hole at the top, into position with the sides resting in the grooves of the braces

on the side panels and against the front of the ramp.

21. Attach the RESET BUTTON, with the long white wire, through the hole in the FRONT END APRON, P5, by removing

the washer and nut on the back of the Reset Button, feeding the Reset Button and wire through the hole from the front and

re-attaching the washer and nut. Note: Be careful not to damage or break wire connections while attaching Reset Button.

Reset Button -

(this ships

pre-wired to

Target Board)

Autres manuels pour NG2015

Table des matières

Autres manuels Hathaway Jeu

Hathaway

Hathaway BG50396 Manuel utilisateur

Hathaway

Hathaway NG2555 Manuel utilisateur

Hathaway

Hathaway SILVERSTREAK NG1029H Manuel utilisateur

Hathaway

Hathaway OUTLAW NG1040 Manuel utilisateur

Hathaway

Hathaway VINTAGE TIC TAC TOE SET Manuel utilisateur

Hathaway

Hathaway EXCALIBUR BG5030 Manuel utilisateur

Hathaway

Hathaway Alpine BG3147 Manuel utilisateur

Hathaway

Hathaway Dorsett Manuel utilisateur

Hathaway

Hathaway PRO Series Manuel utilisateur

Hathaway

Hathaway PLAYOFF BG1031F Manuel utilisateur

Hathaway

Hathaway Bandit NG5029 Manuel utilisateur

Hathaway

Hathaway MONTECITO NG5022 Manuel utilisateur

Hathaway

Hathaway Hat Trick BG1015H Manuel utilisateur

Hathaway

Hathaway NG4070 Manuel utilisateur

Hathaway

Hathaway NG1044 Manuel utilisateur

Hathaway

Hathaway BG50360 Manuel utilisateur

Hathaway

Hathaway Magnum BG1042D Manuel utilisateur

Hathaway

Hathaway STRIKER NG4012TR Manuel utilisateur

Hathaway

Hathaway NG2237BL Manuel utilisateur

Hathaway

Hathaway BG2019SK Manuel utilisateur

Hathaway

Hathaway BG2315P Manuel utilisateur

Hathaway

Hathaway Stratford NG1034FB Manuel utilisateur

Hathaway

Hathaway NG5026 Manuel utilisateur

Hathaway

Hathaway MONTECITO NG5021 Manuel utilisateur

Manuels Jeu populaires d'autres marques

Outdoor Play

Outdoor Play Box it! 2020 Manuel utilisateur

Beleduc

Beleduc Papilio Manuel utilisateur

Costway

Costway UY10001 Manuel utilisateur

Vex

Vex Add It Up Manuel utilisateur

DGT

DGT Centaur Manuel utilisateur

Radica Games

Radica Games BUCKAROO 630 Manuel utilisateur

Fundex Games

Fundex Games Timber Tumble Manuel utilisateur

Go! Gater

Go! Gater 1-1-16453-TP02 Manuel utilisateur

Smoby

Smoby BBF Challenger Manuel utilisateur

Roberto Sport

Roberto Sport INGLESE Manuel utilisateur

Beleduc

Beleduc XXL Witches' Kitchen Manuel utilisateur

Koala Technologies

Koala Technologies KoalaWare Spider Eater Manuel utilisateur

Tomy

Tomy The Magic Oven Manuel utilisateur

Sega

Sega GAME SHOW Manuel utilisateur

Tiger Electronics

Tiger Electronics Last Out 7-584-0 Manuel utilisateur

Fisher-Price

Fisher-Price RollOverRover Manuel utilisateur

Mattel

Mattel World Championship Football Manuel utilisateur

Haba

Haba Dragon Diego Dart Manuel utilisateur