Harvest TEC 445Z Manuel utilisateur

445Z-21-INST

5-21

Installation Manual

Model 445Z

55-Gallon Preservative Applicator

Forage Harvester

DECLARATION OF INCORPORATION

MANUFACTURER: Harvest Tec Inc.

2821 Harvey St.

P.O. Box 63

Hudson, WI 54016, U.S.A.

REPRESENTATIVE ESTABLISHED IN COMMUNITY: Profitable Farming Company

Middle Barlington, Roborough

Winkleigh, Devon, EX19 8AG

ENGLAND

The person above certifies and declares that:

VIRTUAL MACHINE: Equipment mounted on a farm press and for the application of innoculants onto

forage crops.

MODEL: 445Z-21-INST-Imp&Metric

BRAND: Harvest Tec

SERIAL NUMBER:

This application preservatives for hay Harvest Tec system meets the Directive 2006/42/EC of the

European Parliment and the Council of 17 May 2006 and other applicable European Directives

including Directive 2004/108/EC on the Electromagnetic compatability.

The application of preservatives for hay Harvest Tec system will be turned on after being installed on

a farm press has been declard in conformity with the Machinery Directive.

Person in the community authorized to provide information on the partly completed machinery and

making this statement:

Richard Snell, President, Profitable Farming Company

Signed on May 21, 2011: Middle Barlington, Roborough

Winkleigh, Devon, EX19 8AG

ENGLAND

Harvest Tec 445Z Installation Table of Contents

PAGE

Introduction

Tools Needed

Installation of Applicator

4-11

Installation Tank and Saddle

4-5

Installation of Pump Mounting Bracket

Installation of Electronic Pump Assembly

Installation of Drain/Fill Line

Installation of Gauge and Hose Manifold

Placement of Spray Nozzle Assembly

Installation of Plumbing

Installation of Controls and Routing the Wire Harnesses

Parts Breakdowns

11-14

Model 445Z Base Kit

Model 457 Control Box & Drain / Fill Line

445Z Installation Kit

13-14

Warranty Statement

Introduction

Thank you for purchasing a Harvest Tec Model 445Z Hay Preservative Applicator. Please read this manual

carefully to ensure correct steps are followed to attach the applicator to the baler. This applicator is designed

to apply Harvest Tec buffered acid. The model 445Z Kit includes the following parts: tank, frame, pump,

gauge, hose, electronic control box, and miscellaneous hardware. If you are unsure about your kit, contact

your local dealer for specifications. For your convenience parts break downs are included in the back of this

manual.

Left and Right sides are determined by facing in the direction of forward travel.

Tools Needed

SAE wrench set

Metric socket set

SAE socket set

Standard screw driver

Hose cutter

Drill bit set

Crescent wrench

Hammer

Center punch

Side cutter

Measuring tape

Installation of Applicator

Installation of Mounting Brackets and Tank

1. Locate parts 001-4703ZR-A, 001-4703ZR-B, two 001-4703ZR-C and four ¾” x 4 ½” bolts, lock

washers and nut.

2. Line up 001-4703ZR-A and 001-4703ZR-B about 18 inches apart on the ground. Slide part

001-4703ZR-C into square mounts and secure with ¾” x 4 ½” bolts, locks, and nuts to holed

in place. Note there are two sets of ¾” holes on the 001-4703ZR-C. Use the set that is about

18 inches apart.

3. Locate part 001-4703ZR-D1 and two ½” x 5 ½” bolts, locks, washers, and nuts. Bolt part 001-

4703ZR-D1 to the top of the two 001-4703ZR-C with this hardware.

4. Locate part 001-4703ZR-D2. Bolt to the front of 001-4703ZR-D1 with ½” x 3 ½” bolts,

washers, locks, and nuts. Do not fully tighten down.

5. Using a lift, bring the assembly up under the cab of the baler. Part 001-4703ZR-D2 should

line up with holes in the front part of the baler. Mark the half inch holes at the ends of the 001-

4703ZR-A and 001-4703ZR-B that line up with the structural parts under the cab. Lower

assembly out of the way and drill these four holes with a 9/16” drill bit. (Note. Do not drill into

hydraulic lines or electrical wires.

6. Once holes have been drilled. Lift assembly back up under cab and attach to baler with four

½” x 3 ½” bolts, washers on both sides, locks, and nuts. ¾” hardware is provided if you would

want to use this. However, part 001-4703ZR-A and 001-4703ZR-B will need to be drilled out

for the ¾” bolts. The 001-4703ZR-D2 will attach to the front mount with ½” x 2” bolts, washers

on both sides, locks, and nut.

7. Attach two 001-4703ZR-E to each 001-4703ZR-C (one on each side) sticking out the front of

the baler. Use ¾” x 4 ½” bolts, locks, nuts. Do not fully tighten down yet.

8. Attach 001-4703ZR-G to the 001-4703ZR-E at the height you desire to keep the tank about

the windrow. Note the lower the take the closer it is to the windrow coming into the baler.

The higher it will obstruct your view. Use ¾” x 4 ½” bolts, locks, and nuts to secure.

9. Attach 001-4703ZR-G to 001-4703ZR-F with ½” x 4” Bolts, washers, locks, and nut. Do not

fully tighten down. (Note: angles will be pointing toward each other.

10.Place saddle assembly on 001-4703ZR-G and secure with ½” washer, locks, and nuts.

11.Tighten all hardware down.

001-4703ZR-F

001-4703ZR-G

001-4703ZR-A

001-4703ZR-B

001-4703ZR-C

001-4703ZR-D1

001-4703ZR-E

001-4703ZR-D2

Installation of Mounting Brackets and Tank (continued)

Mount Pump Plate Assembly

Locate parts bag 8. Using two 3/8” x 1/4” bolts, locks, washers, and nuts. Mount the U-shaped pump plate

mount 001-4647 (right) onto the tank saddle in the mounting holes located between the strap brackets on

back of saddle (figure 7).

Connect the pump plate mounting bracket (001-4648X), shown in figure 8, using two 3/8”x 1 1/4" bolts, nuts,

locks, and flat washers to the mounting bracket. Install the pump plate as shown completed in figure 9.

Figure 7

Figure 8

Figure 9

Figure 10

Installation of Gauge and Hose Manifold

A. Drill two 3/8” holes and mount pressure gauge to sheet metal. Bend the gauge bracket to adjust the

angle.

B. Secure with two 5/16” x 1” flange bolts and flange nuts.

Placement of Spray Nozzle Assembly

The cross bar on the wind guard above the pick-up head provides a mounting point for the nozzle holders

(001-4714J). Mount the nozzle holders on the wind guard, using the supplied U bolts (001-4714UBS).

Measuring from the center of the baler, the nozzle holders will need to be 6” (15cm) apart on a 4’ (1.2M) and

9” (23cm) apart on a 5’ (1.5M) Do not fully tighten.

Position the nozzle holders so that the tips spray in a horizontal direction over the top of the baler’s pickup.

The tips should be located so that they will be between 14” and 18” (35 - 45 cm) from the normal path of hay.

Make sure the nozzle holders do not interfere with the tying system. *It is recommended to test the system

with water prior to field operation. This will ensure the fan pattern from the tips reaches the outside edges of

the pickup while having a slight overlap in the center.

Installation of Plumbing

A. Tank to Pump

1. Thread elbow (003-EL3412) into the bottom of the tank.

2. Route 1/2” hose from bottom of tank through gap in sheet metal surrounding the baler gauge down

to valve on pump intake.

3. Secure with hose clamps.

B. Pump to Gauge

1. Attach 1/2” hose to pump discharge and route up to gauge. Secure with hose clamps.

C. Gauge to Nozzles

1. Attach 1/2” hose to open port of gauge and route hose down to check valve of spray nozzle

assembly.

2. Attach quick disconnect (003-A1412 and 004-1207H).

3. Secure with hose clamps.

D. Secure loose hoses to baler with supplied Jiffy clips. Use existing hardware to attach to baler.

Filter bowl assembly

Gauge

Nozzle

tubes/hoses

spray

assemblies

Tank

Installation of Controls and Routing the Wire Harnesses

A. Locate the control in an area that allows operation for adjusting or turning the controls while operating

the baler.

B. Route the wire to the starter solenoid on all 12V tractors. Connect the green lead marked +to the hot

terminal on the starter. Connect the black lead to a good ground. Do not reverse the leads. Be sure

to use a voltmeter to verify that you do have 12 volts running to the box.

Note: For tractors with 24v starters, connect the power leads to the tractor’s right-hand battery. Do not

connect the leads to the starter. Connect the lead marked + to the positive battery terminal and the lead

marked- to the negative on the battery. Wiring connections to the battery normally results in corrosion;

terminal coating is recommended.

C. Attach the wire from the pump to the battery

D. Run wire with molded black plug to back of tractor

E. Run wire from pump up drawbar and connect it to the mating plug from the control box. Secure wire to

baler with supplied cable ties.

Caution: Do not run a pump or use an electronic control box directly off a battery charger. For stationary use,

the applicator can be connected to a new battery and the battery connected to a charge

Model 445Z

Base Kit

Ref

Description

Part #

Qty

Ref

Description

Part #

Qty

50 Gallon Tank

005-9203SQ

Side Rail Plate

001-4703ZR-E

Tank Cap, Gasket, & Breather

P05-9022HBG

Front Mount Support

001-4703ZR-D2

Tank Saddle

001-4703X

Front Mount Crossmember

001-4703ZR-D1

Tank Strap

001-4402

Long Side Rail

001-4703ZR-C

Tank Saddle Support

001-4703ZE-G

Mid Mount

001-4703ZR-B

Short Side Rail

001-4703ZR-F

Rear Mount

001-4703ZR-A

Hex Plug

003-F34

Complete Kit

030-0445Z-TK

Autres manuels Harvest TEC Matériel agricole

Harvest TEC

Harvest TEC 493 Manuel

Harvest TEC

Harvest TEC 442C Manuel utilisateur

Harvest TEC

Harvest TEC 600BB Manuel utilisateur

Harvest TEC

Harvest TEC 300SS Manuel utilisateur

Harvest TEC

Harvest TEC 300RBC Manuel utilisateur

Harvest TEC

Harvest TEC 696 Manuel utilisateur

Harvest TEC

Harvest TEC 201LS Manuel utilisateur

Harvest TEC

Harvest TEC 600BB Manuel utilisateur

Harvest TEC

Harvest TEC 300 Series Manuel utilisateur

Harvest TEC

Harvest TEC 600RBC Manuel utilisateur

Harvest TEC

Harvest TEC 458 Manuel utilisateur

Harvest TEC

Harvest TEC 445T Manuel utilisateur

Harvest TEC

Harvest TEC 547C Manuel utilisateur

Harvest TEC

Harvest TEC 644 Manuel utilisateur

Harvest TEC

Harvest TEC AGCO 600A1 Manuel utilisateur

Harvest TEC

Harvest TEC 300RB Manuel utilisateur

Harvest TEC

Harvest TEC 600SS Manuel utilisateur

Harvest TEC

Harvest TEC 436 Manuel utilisateur

Harvest TEC

Harvest TEC 700 Manuel utilisateur

Harvest TEC

Harvest TEC 720 Manuel utilisateur

Harvest TEC

Harvest TEC 720 Dew Simulator Manuel utilisateur

Harvest TEC

Harvest TEC 744 Manuel utilisateur

Harvest TEC

Harvest TEC 442U Manuel utilisateur

Harvest TEC

Harvest TEC 491BB Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur